Answer:
B
Explanation:
Frequency and wavelength are inversely proportional
Please help me fast! Pleaseee
I think 2 answer is write
Please help me! I am a bit stuck on this.
Calculate the solubility of copper(II) hydroxide, Cu(OH)2, in g/L
Answer:
Ksp = [ Cu+² ] [ OH-] ²
molar mass Cu(oH )2 ==> M= 63.546 (1) + 16 (2) + 1 (2) = 97.546 g/mol
Ksp = [ Cu+² ] [ OH-] ²
Ksp [ cu (OH)2 ] = 2.2 × 10-²⁰
|__________|___Cu+² __|_2OH-____|
|Initial concentration(M)|___0__|_0______|
|Change in concentration(M)|_+S |__+2S__|
|Equilibrium concentration(M)|_S _|2S___|
Ksp = [ Cu+² ] [ OH-] ²
2.2 ×10-²⁰ = (S)(2S)²= 4S³
[tex]s = \sqrt[3]{ \frac{2.2 \times {10}^{ - 20} }{4} } = 1.8 \times {10}^{ - 7} [/tex]
S = 1.8 × 10-⁷ M
The molar solubility of Cu(OH)2 is 1.8 × 10-⁷ M
Solubility of Cu (OH)2 =
[tex]Cu (OH)2 = \frac{1.8 \times {10}^{ - 7} mol \:Cu (OH)2 }{1L} \times \frac{97.546 \: g \: Cu (OH)2}{1 \: mol \: Cu (OH)2} \\ = 1.75428 \times 10 ^{ - 5} [/tex]
Solubility of Cu (OH)2 = 1.75428 × 10 -⁵ g/ L
I hope I helped you^_^
molecular weight of K2SO3
Explanation:
the molecular weight of K2SO3 is 158. 2598 m/s.
PLEASE HELP ME
a)
b)
c)
or d)?
Answer:
D / 15.0 g
Explanation:
3 % volume thus shows that there are 3 g of an solute in every 100mL of solutions
.. there will be 3 × 5000÷ 100 of H2O2 in a 500 mL bottle
Over a long period of time the process of deposition causes the formation of
O
A. acid rain
OB. glaciers
OC. sedimentary rock
OD. Karst topography
Answer:
C. sedimentary rock
Explanation:
Deposition is basically a process in which sediments are added to land.
Chuẩn Độ 15 ml dung dịch CH3COOH 0,2 m bằng dung dịch NaOH 0,2 m
A* tính PH tại các thời điểm trên thêm 10 ml bazơ
* tại thời điểm tương đương
Answer:
I don't know what is the answer of your question sorry never mind..Explanation:
And please marks me as brainliest...Read the given equation:
Ca(OH)2 + 2HCl → CaCl2 + 2H2O
Which of the following is true about the equation?
Ca(OH)2 is the base and CaCl2 is the salt.
Ca(OH)2 is the acid and CaCl2 is the salt.
HCl is the acid and Ca(OH)2 is the salt.
HCl is the base and Ca(OH)2 is the salt.
Answer:
Ca(OH)2 is the base and CaCl2 is the salt
Explanation:
i think this is the answer because calcium hydroxide has hydroxide ions as the only positively charged ion and calcium chloride is a salt.
I hope this helps
The chemical equation for the formation of calcium chloride has Ca(OH)₂ as the base and CaCl₂ as the salt. Hence, option A is correct.
What is salt?Salt is given as the neutral compound with the presence of the acidic and the basic constituents. The salt can be formed as a result of the neutralization reaction of acid and base.
The acids are comprised of the presence of the hydrogen ion, and the base comprises the presence of the hydroxide ions. Thus, in the given reaction, Ca(OH)₂ is the base and CaCl₂ is the salt. Hence, option A is correct.
Learn more about salt, here:
https://brainly.com/question/10208023
#SPJ2
Determine if each compound is an alkane, alkene, alkyne, or aromatic compound. This compound has the formula C H 3 C H C (C H 3) C H 2 C H 2 C H 2 C H 3. There is a double bond between carbons two and three. aromatic alkyne alkene alkane This compound consists of a six membered carbon ring with alternating double and single bonds. There is a C H 2 C H 3 group attached to one of the carbon atoms in the ring. alkyne aromatic alkane alkene CH3CH2COCH3 alkyne aromatic alkene alkane CH3(CH2)2CH3 alkane aromatic alkene alkyne
Answer:
C H 3 C H C (C H 3) C H 2 C H 2 C H 2 C H 3
Explanation:
.) At 500 oC, cyclopropane, C3H6, rearranges to form propene. The reaction is first order with a rate constant of 6.7 x 10-4 s-1. If the initial concentration of C3H6 is 0.0500 M, (a) what is the molarity of C3H6 after 30 min
Answer:
0.015 M
Explanation:
For a first order reaction;
ln[A] =ln[A]o - kt
[A] = final concentration
[A]o =initial concentration
k= rate constant
t= time taken
ln[A] =ln[A]o - kt
ln[A] = ln(0.0500) - 6.7 x 10-4 (30 × 60)
ln[A] = -2.9957 - 1.206
ln[A] = -4.202
e^ln[A] = e^(-4.202)
A= 0.015 M
Good afternoon everyone, Define Radicals?Thank You
Explanation:
A radical is is an atom, molecule, or ion that isnt paired up with at least one valence electron.
Answer:
a radical also called a free radical is a molecule that contains at least one unpaired electron.
I hope this helps
What is the H+ ion concentration of a solution with a pH of 7?
answer=H+]=10-7
explain=the same way, a solution with a pH of 5 contains 10-5mol/l of hydrogen ions, a solution with a pH of 6 contains 10-6mol/l of hydrogen ions, while the solution with a pH of 7 contains 10-7mol/l of hydrogen ions
How much heat does a 100. g sample of copper absorb when its temperature increases by 30.0°C? The specific heat of copper is 0.39 J/g °C.
a) 2340 J
b) 1170 J
c) 2.34 J
d) 1.17 J
Answer:
[tex]\boxed {\boxed {\sf B. \ 1170 \ Joules }}[/tex]
Explanation:
We are asked to find how much heat a sample of copper absorbs when the temperature is increased.
Since we know the mass, temperature increase, and specific heat capacity, we can use the following formula to calculate heat.
[tex]q= mc \Delta T[/tex]
The mass of the copper sample is 100 grams, the temperature is changed or increased by 30.0 degrees Celsius, and the specific heat of copper is 0.39 Joules per gram degrees Celsius.
m= 100 g c= 0.39 J/g °C ΔT= 30.0 °CSubstitute the values into the formula.
[tex]q= (100 \ g )(0.39 \ J/g \textdegree C ) (30.0 \textdegree C )[/tex]
Multiply the first two values. Note that the units of grams cancel.
[tex]q= 39 \ J/ \textdegree C (30.0 \textdegree C )[/tex]
Multiply again, this time the units of degrees Celsius cancel.
[tex]q= 1170 \ J[/tex]
The copper sample absorbs 1170 Joules of heat and Choice B is correct.
Methane (CH4) is the major component of natural gas. 40.0 grams of methane were placed in a commercial calorimeter and subjected to a combustion reaction. The reaction released 2800 kJ of energy.
1. Compare this energy value to the energy values of paraffin and isopropanol. Is methane a good choice as a fuel?
Based on comparison of energy produced per kilogram, a given mass of methane produces more energy than similar masses of either paraffin or isopropanol, therefore;
Methane is a good choice as a fuel
The reason for the above comparison conclusion is as follows:
The given information:
The details of the combustion of the methane gas, CH₄, are as follows;
The mass of the methane gas placed in the calorimeter, m = 40.0 g
The amount of heat released from the combustion of the 40.0 grams of methane = 2,800 kJ
The data from online resources of paraffin and isopropanol includes
1. The energy value of paraffin = 46 MJ/kg
The energy value of isopropanol = 33.6 MJ/kg
The energy produced from 1 kilogram of methane gas is given as follows;
40.0 g of methane gas produces 2,800 kJ of energy, therefore;
1 kg = 1,000 g of methane gas will produce, 2,800kJ/(40.0 g) × 1,000 g = 70,000,000 J
Therefore;
1 kg of methane produces 70,000,000 J = 70 MJ of energy
Therefore, energy produced from methane = 70 MJ/kg
Given that methane produces more than twice the amount of energy that
is produced from similar mass of isopropanol and more than one and half
times the amount of energy that is produced from the same mass of
paraffin, methane is a good choice as a fuel for energy
Learn more about the calorific value of fuels here:
https://brainly.com/question/24095281
I bet no one can solve this
If an electric current of 8.50 A flows for 3.75 hours through an electrolytic cell containing copper-sulfate (CuSO4) solution, then how much copper is deposited on the cathode (the negative electrode) of the cell? (Copper ions carry two units of positive elementary charge, and the atomic mass of copper is 63.5 g/mol.)
What is photosynthesis??...
the process plants use sunlight to synthesize food
Answer:
It is when green plants and other organisms transform light energy into chemical energy.
9. In order to determine the melting point of tetradecanol, it was important that _____. the thermometer was attached to the capillary tube the water was frozen the capillary tube was immersed in the water without the thermometer
To record the melting point of tetradecanol, it is important the temperature is increase by little degrees after each trial.
The thermometer attached to the capillary tube was immersed in water without thermometer.
Usually heating curve describes the temperature change for a sample which passes through different states of matter.
The temperature than decreases and the solution in beaker cools down. To determine the melting point, it is important to keep the temperature consistent.
Learn more at https://brainly.com/question/24335381
calculate the total consumer surplus in the amusement park market if they a 12
Answer:
The total consumer surplus is 240.
Explanation:
If p=12 then q=20
0.5×(36−12)×20=240
here's the graph to help you see the change.
A 6.0-L vessel was found to contain 1.0 mol BrCl 3 , 2.0 mol Br 2 and 6.0 mol Cl 2 at equilibrium. What is the equilibrium constant, K c , for this equilibrium mixture for the reaction 2BrCl 3 (g) Br 2 (g) 3Cl 2 (g)
Answer:
Writing a balanced Equation for the reaction
Br₂ + 3Cl₂ ==> 2BrCl₃
Kc = [BrCl₃]² / [Br₂][Cl₂]³
Each Concentration (n) = moles/volume of container.
(nBrCl₃)= 1/6 = 0.167moldm-³
(nBr₂) = 2/6 = 0.333moldm-³
(nCl₂) = 6/6 = 1moldm-³
Kc = (0.167)² / (0.333)(1)³
Kc = 0.0838.
PLEASE HELP!!
this is on USAtestprep
a)
b)
c)
d)
Answer:
C.
Explanation:
In warm air, stuff expands, and in cold air, things condense, or decrease in size.
How is a light bulb related to radiation?
A. Light bulbs do not have anything to do with radiation.
B. A light bulb emits radiation when its filament is burned out and can longer emit light. This makes it important to remove dead lightbulbs as soon as they wear out.
C. As light is emitted from the filament, the energy in the metal is replaced as lightbulbs absorb background radiation. This prevents the filament from burning out quickly but the radiation cannot be used as power so electricity is still required for the lightbulb to work.
D. The light emitted by a light bulb is a form of radiation that occurs when the filament heats up and its thermal emission gains enough energy to move into the visible spectrum.
Answer:
As light is emitted from the filament, the energy in the metal is replaced as lightbulbs absorb background radiation. This prevents the filament from burning out quickly but the radiation cannot be used as power so electricity is still required for the lightbulb to work.
Atoms that have a positive or negative electrical charge are called ________.
Explanation:
They are called or known as cations
How many neutrons does Carbon- 14 and Carbon -15 have? *
Answer: 8 for both
Explanation:
Please comment the chart!!!!!
thanks!!
Answer:
Exothermihic chart
Explanation:
Which one of the following compounds
contains ionic bonds?
a) NI3
B) HF
c) SiO2
d) CaO
Your answer is CaO.I hope that my answer helped you..
Do the tests performed to identify DNA exclude the presence of RNA?
DNA and RNA can also be ISOLATED from the same biological sample.
So the answer is no, both DNA and RNA are together.
Answer:
so the answer is no
both DNA and RNA are together.
Explanation:
DNA and RNA can also be ISOLATED from the same. biological sample
Draw a formula for Thr-Gly-Ala (T-G-A) in its predominant ionic form at pH 7.3. You may assume for the purposes of this question that the pKa values of the acidic groups of amino acid residues in the peptide are the same as in the amino acid itself.
Answer:
gggggggggg
Explanation:
gggggggg
The tripeptide formed from threonine, glycine and alanine is neutral at the pH of 7.3. The carboxylic end is negative charged by donating its proton to form the NH₃⁺ group.
What is peptide?Peptides are protein units formed from two or more amino acids bonded through peptide bonds. There are essential and non-essential amino acids. Essential amino acids have to be uptake from food and non-essential amino acids are synthesized inside the body.
Threonine is an essential amino acid with a CH₃CHOH side group. Glycine has the simplest side group hydrogen and alanine has CH₃ side chain. Both glycine and alanine are non-essential amino acids.
Each amino acids are represented with a three letter code or one letter symbol. Thus threonine is T, G for glycine and A for alanine. At a pH of 7.3 the peptide formed from these amino-acids contains a negatively charged carboxylic end.
A positively charged amino end made by protonation from the acid group make the overall charge zero. The structure of the peptide is given in the uploaded image.
To find more about peptides, refer the link below:
https://brainly.com/question/11843803
#SPJ2
Which compound shows maximum hydrogen bonding with water? a-Methyl Alcohol b-Ethyl alcohol. Give reason too please.
A) In ethanol, the OH group is present. This means an H atom is attached to an O atom. The electronegativity of an O atom is much greater than an H atom because of this the H atom will get a partial positive charge and the O atom will get a partially negative charge. This is known as a dipole. Hence dipole-dipole interactions will get generated in the molecule and attractive forces will be produced among the molecules of ethanol.
B) There is no hydrogen bonding between diethyl ether molecules because there is no hydrogen atom attached to an electronegative atom like oxygen or nitrogen. So diethyl ether does not show hydrogen bonding.
C) Chlorine is less electronegative as compared to oxygen and nitrogen so it does not show hydrogen bonding. So, ethanol has more hydrogen bonding than ethyl chloride.
D) In trimethylamine, the nitrogen atom is not attached to any hydrogen atoms. So, it will not show any hydrogen bonding.
According to above mentioned points, we can conclude that out of the given options ethanol will have maximum hydrogen bonding.
So, the correct option is (A).
Additional Information:
Properties of hydrogen bonding :
i) Solubility: Because of the hydrogen bonding between water and alcohol molecules, lower alcohols are soluble in water.
ii) Volatility: Compounds having hydrogen bonding between different molecules have a higher boiling point and a higher boiling point means the compound is less volatile.
iii) Viscosity and surface tension: The substances which contain hydrogen bonding exist as an associated molecule. They have higher viscosity and high surface tension
9. Light is used in photosystem II and photosystem I to
O A. power the Calvin cycle.
B. fix carbon dioxide.
C. make carbon dioxide.
D. excite an electron.
Answer:
A. power the Calvin cycle.
Explanation:
because it helps to run theblife of plants with easily
C2H5MgBr + PCl3 ra chất gì
Answer:
C2H5P
is the right answer
