1.slope of distance time graph gives______in the case of uniform motion.

2.The magnitude of velocity and______will be equal if motion is along a straight path.

​

Answer:

[tex]\boxed {\boxed {\sf 15 \ m/s \ or \ 15 \ m*s^{-1}}}[/tex]

Explanation:

We are asked to find the final velocity. We are given the acceleration, time, and initial velocity, so we can use the following kinematics formula.

[tex]v_f= v_i+ at[/tex]

In this formula, [tex]v_f[/tex] is the final velocity, [tex]v_i[/tex] is the initial velocity, [tex]a[/tex] is the acceleration, and [tex]t[/tex] is the time.

The bicycle has an initial velocity of 5.0 m *s⁻¹ or m/s, acceleration of 2 m/s², and a time of 5 seconds.

[tex]\bullet \ v_i = 5.0 \ m/s \\\bullet \ a= 2\ m/s^2\\\bullet \ t= 5 \ s[/tex]

Substitute the values into the formula.

[tex]v_f=5.0 \ m/s + ( 2\ m/s^2 * 5 \ s)[/tex]

Solve inside the parentheses.

[tex]v_f= 5.0 \ m/s + (10 \ m/s)[/tex]

Add.

[tex]v_f= 15 \ m/s[/tex]

The units can also be written as:

[tex]v_f= 15 \ m*s^{-1}[/tex]

The bicycle's final velocity is 15 meters per second.

Answer:

The emf of a cell is the sum of the electric potential differences (PDs) produced by a separation of charges (electrons or ions) that can occur at each phase boundary (or interface) in the cell. The magnitude of each PD depends on the chemical nature of the two contacting phases.

Explanation:

pls mark brainliest

Although you did not mention the "described data collection," we can help you answer in the following terms.

The three potential challenges or important points to consider when conducting data collection are:

1.- To correctly establish the specific information needed to get as a result of the research.

2.- The kind of methodology appropriate to get that expected data.

3.- The process needed to analyze and interpret that data.

- As well, it is of the utmost importance that the researcher considers the type of data compared to the budget needed to get it. Here, the budget should consider the cost of the collection process.

- Of course, the result of the process has to result in data that is valid and accurate, because that is the nature of a good research project.

Here we have to stress the relevance of the establishment of a good hypothesis to start the collection process, no matter the data collection methods used to get the data such as interviews, focus groups, observations, and so on.

We can conclude that collection data is a rigorous process that should be strictly followed to really obtain the kind of data needed to support the foundation of any research.

Learn more about this topic here:

https://brainly.com/question/14340459?referrer=searchResults

A variable, as its name implies, is something that can change, ideally, as the scientists and engineers want to.

Particularly we care for the independent variables, which are the ones we can control and affect the dependent variables, which are the outcomes we study.

For a quick example, think of an experiment where you heat something on an oven. The temperature of the oven can be set by the scientist, so the temperature is an independent variable because they can control it.

Now let's see the given experiment.

The team is testing the speed of the toy car.

remember that:

distance/time = speed.

We know that in the first trial, they test how long takes the car to travel 2 meters.

Now, what we can change for the second trial, knowing that the speed is the output that we are studying?

The answer is trivial, the only thing we can change in the given setup is the distance that the car travels, so in the next trial we should change the variable "distance travelled by the car" and see if it affects the output "speed of the car".

If you want to learn more about variables, you can read:

https://brainly.com/question/19585043

1:-

[tex]\\ \sf\longmapsto cos\Theta=\dfrac{B}{H}[/tex]

[tex]\\ \sf\longmapsto cos\Theta=\dfrac{4}{5}[/tex]

2:-

[tex]\\ \sf\longmapsto tan\Theta=\dfrac{P}{B}[/tex]

[tex]\\ \sf\longmapsto Tan\Theta=\dfrac{3}{4}[/tex]

Key Notes:-

Answer:

Cos A = 4/5

Tan A = 3/4

Explanation:

Cos A = Adjacent/Hypotenuse = 4/5

Tan A = Opposite/Adjacent = 3/4

Answer with Explanation:

Let me answer this in a simple way, since the density of stone is greater than that of water, the stone sinks as the weight of the stone is greater than the weight of water displaced by it. But the ship is designed in such a way that the relative density of the ship always becomes less than that of water. Therefore, the weight of the water displaced becomes equal to the total weight of the ship and thus it floats.

There are many other ways to explain this but this should give you the general idea.

The frequency of the wave for the stone thrown in the pond is 0.5Hertz.

The question does not specify what to calculate but we can look for the frequency of the wave.

Frequency is the number of oscillations completed in one second. This is interpreted as:

x oscillations = 1second

If Five waves were made from the same source in 10 seconds for a stone that is thrown inside the pond, then:

5 oscillations = 10seconds

Divide both expressions to get x (the required frequency)

x/5 =1/10

Cross multiply

10x = 5

Divide both sides by 10

10x/10 = 5/10

x = 1/2

x = 0.5Hertz

Hence the frequency of the wave is 0.5Hertz.

NB: The period of the wave is simply the reciprocal of the frequency.

Learn more here: https://brainly.com/question/13728731

my views

Explanation:

Figure (8) shows a rod made up of copper and wood joined together. The rod is heated at the joint in the centre for about a minute. At which point – A, B, C or D, would it show the lowest temperature? PLEASE GIVE REASONS ALSO(MINIMUM 2)

the machine shown in the diagram is called a tramp.

the height of the tramp is 5 and the length is 12

Answer:

Incline plane

5/12 rise/run

Explanation:

Incline plane

5/12 rise/run

Answer:

Because Star A and Star B have identical luminosities, the difference in their apparent brightness is due solely to distance. Star B is twice as far from Earth as Star A.

Explanation:

Answer:

OK well

Explanation:

where's the question bring it first

Answer:

ExplanationjakkJXJAKGKXAHLKHQHL:

Answer:

distance between should be 1.25 × 10^6 m

Explanation:

Force is proportional to separation distance.

[tex]250 \: newtons = 2.5 \times {10}^{6} \: metres \\ ( \frac{1}{2} \times 250) \: newtons = d \\ \\ d = \frac{125 \times 2.5 \times {10}^{6} }{250} \\ d = 1.25 \times {10}^{6} \: metres[/tex]

Answer:

distance between should be 1.25×10^6.

Explanation:

force Is proportional to separation .

mrk above answer branilest .

Answer:

Longshore drift has a very powerful influence on the shape and composition of the coastline. It changes the slopes of beaches and creates long, narrow shoals of land called spits, that extend out from shore. Longshore drift may also create or destroy entire “barrier islands” along a shoreline.

F = m · g

m = 1485 kg

g = 10 N/kg

F = 1485 kg · 10 N/kg = 14 850 N = 14,85 kN

Answer: The weight on Earth is 14,85 kN.

Answer:

Lever systems are simple machines that change or increase the input force that we apply to the load. The lever provides us with some mechanical...

Answer:

● Effort arm or Effort distance (ED): The perpendicular distance from the fulcrum to the point of effort is called effort arm.

● Load arm or Load distance (LD): The perpendicular distance from the fulcrum to the point of load is called load arm.

Explanation:

because the moon has less mass than earth, the force due to gravity at the lunar surface is only about 1/6 that on earthso,the weight of a body on earth is 6×5N =30N

Answer:

The particle is defined as the small quantity of matter under the consideration. ... The wave is defined as the propagating dynamic distrubance. The energy of the wave is calculated based on the wavelength and velocity

Explanation:

In Physics, we distinguish between wave motion and particle motion. Wave motion refers to the movement of a wave-like pattern from one location on the medium to another. ... When you observe the motion of these points, you are observing particle motion - the motion of particles of the rope.

The magnitude (size or numerical value) and the direction.

Hope this helps!!! :)

Answer:

false...............

Answer:

False A beginners should start from shorter ones to long work sessions

Explanation:

Hope it helps

Mark me as Brainliest plz!!

:DD

Answer:

Explanation:

where W-weight, m-mass of the object and g-acceleration produced due to the earth's gravity. ... This happens because the normal reaction force exerted on the object in the lift is equal to zero, and normal force equals to mg, which in turn equals the weight of the object.

(a) The recoil or backward velocity of the gun is 8 m/s.

(b) The bullet cannot penetrate the plank of the wood completely.

The given parameters include;

(a) The backward or recoil velocity of the gun is calculated by applying the principle of conservation of linear momentum.

m₁u₁  + m₂u₂ = 0

m₂u₂ = -m₁u₁

[tex]u_2 = -\frac{m_1u_1}{m_2} \\\\u_2 = - \frac{0.1 \times 400}{5} \\\\u_2 = -8 \ m/s[/tex]

Thus, the recoil or backward velocity of the gun is 8 m/s.

(b) determine if the bullet can penetrate the plank of the wood completely

the acceleration of the bullet is calculated as;

v² = u₁² + 2as

2as = v² - u²

[tex]a = \frac{v^2 -u_1^2}{2s} \\\\a = \frac{(266.67)^2 -(400)^2}{2\times 0.04} = -1.111 \times 10^6 \ m/s^2[/tex]

Finally, determine the distance traveled by the bullet when it comes to a complete stop, that is the final velocity = 0

[tex]v_f^2 = v^2 + 2ad\\\\2ad = v_f^2 - v^2\\\\d = \frac{v_f^2 - v^2}{2a} \\\\d = \frac{(0) - (266.67)^2}{2(-1.111\times 10^6)} \\\\d = 0.032 \ m[/tex]

d = 3.2 cm

The total distance traveled by the bullet inside the plank = 4 cm + 3.2 cm = 7.2 cm

Therefore, the bullet cannot penetrate the plank completely.

To learn more about linear momentum visit: https://brainly.com/question/15869303

Answer:

Change, or increase, the buoyant force.

Explanation:

As the salt water of the sea is denser than the river's fresh water, the boat will rise when entering the sea from the river and sink (to increase the buoyant force) when entering the river from the sea.

Answer:

13.33 g/cm3

Explanation:

density = mass/volume

mass of irregular body = 800 grams

new volume = 60 cube cm

= density = 800/60  = 13.333 g/cm3

Explanation:

Using Ohm's Law and a bit of substitution, we can use voltage divided by current to solve for resistance. Doing that, we'll get 6 Ohm.

Answer:

.21

Explanation:

i see everyone got it wrong so ill give you the answer, good luck :)

Answer:

// EDU HACK REDDIT EDITON //

if (running == null) {

var running = null; console.log("Program Loading...");

var iframe = document.getElementById("stageFrame");

for (i = 0; i < 1; i++) {

 setInterval(function() {

  if (running == null) { running = true; console.log('Program Loaded! Enjoy!') }

  if (iframe.contentWindow.document.getElementsByClassName('FrameRight') != null) { iframe.contentWindow.document.getElementsByClassName('FrameRight')[0].onclick(); }

  if (iframe.contentWindow.document.getElementById("invis-o-div") != null) { iframe.contentWindow.document.getElementById("invis-o-div").remove(); }

 },1000);

}

} else {

console.log("Program already running!")

}

Explanation:

Almost 3 times fast than normal pulley system

mark me

Answer:

Work done is 5 J

Explanation:

Workdone = Force × distance

[tex]{ \sf{W = 100 \times (5 \times {10}^{ - 2}) }} \\ { \sf{W = 5 \: joules}}[/tex]

Answer:

To convert 400 mm to m you can apply the formula [m] = [mm] / 1000; use 400 for mm. Thus, the conversion 400 mm m is the result of dividing 400 by 1000. 0.4

PLEASE MARK AS BRAINLIEST ANSWER