Transistor circuits are sometimes referred to as switching circuits - Why is this?
Explanation:
One of the most common uses for transistors in an electronic circuit is as simple switches. In short, a transistor conducts current across the collector-emitter path only when a voltage is applied to the base. When no base voltage is present, the switch is off. When base voltage is present, the switch is on.
an 1800 kg car travelling east at 30 m/s slows down to 10 m/s what is the work done by brakes
This was a question on my test do y’all know how to do it cuz I couldn’t figure it out
Answer:
Explanation:
The work done by brake friction changes the kinetic energy,
ASSUMING the road is level and other friction is ignored.
W = KEf - KEi = ½mvf² - ½mvi² = ½m(vi² - vf²)
W = ½(1800)(30² + 10²) = 900(900 - 100) = 720000 J = 720 KJ
Calcular la longitud del faldón de una Rampa de Acceso , que en planta tiene una longitud de 20 m y la pendiente es 27%.
La longitud del faldón de la rampa es de 5.4 m.
La pendiente expresada en porcentaje sigue la siguiente ecuación:
[tex]m=\frac{y}{x}*100[/tex] (1)
Donde:
y es la elevacion de la rampa (faldón)x es la longitud de la ramapa (20 m)Sabemos que la pendiente es de 27%. Por lo tanto, usando la ecuación 1, despejamos y.
[tex]27=\frac{y}{20}*100[/tex]
[tex]y=\frac{27*20}{100}[/tex]
[tex]y=5.4\: m[/tex]
La longitud del faldón es 5.4 m
Pudes ver más sobre el tema aquí:
https://brainly.com/question/8906330
Q)what are convex mirrors?
Answer:
A curved mirror is a mirror with a curved reflecting surface. The surface may be either convex or concave. Most curved mirrors have surfaces that are shaped like part of a sphere, but other shapes are sometimes used in optical devices.
A convex mirror (or lens) is one constructed so that it is thicker in the middle than it is at the edge.
A 12-V battery is connected across a device with variable resisstance. As the resistance of the device increases, determine whether the following quantities increase, decrease, or remain unchanged. Indicate your answers with I, D, or U respectively.
a. The current through the device
b. The voltage across the device
c. The power consumed by the device
Define wave length as applied to wave motion
Answer: Wavelength can be defined as the distance between two successive crests or troughs of a wave. It is measured in the direction of the wave.
Explanation:
Wavelength refers to the length or distance between two identical points of neighboring cycles of a wave signal traveling in space or in any physical medium. ... The wavelength of a signal is inversely proportional to its frequency, that is, the higher the frequency, the shorter the wavelength.
what is the value of Pi
Answer:
the value of pi is approximately 3.14
Explanation:
or pi = approx 3.14159265358979324...
Good morning 2 all ,What is mechanical advantage write its formula. Have a good day thank you ✌
The ratio of foort dustance to load distance in a simple machine is called mechanical advantage or MA.
MA= Effort Distance / Load Distance
You spaceship has a snazzy lounge called Ten-Forward that needs a new spacecouch. Sadly the couch you bought is too long and won't fit into your car when it is stationary. The couch has a length Lc = 14.0 m and mass m = 49 kg, and your shuttlecraft has a length of L = 9.0 m How fast would you need to run, in terms of the speed of light c, in order to get the couch to fit inside the length of the shuttlecraft?
Answer:
v = speed
c = speed of light
using the equation
L = Lc Sqrt( 1 - (v/c)2)
9 = 14 Sqrt( 1 - (v/c)2)
v/c = 0.765
v = 0.765 c
What is the magnitude of the force between a 25μC charge exerts on a -10μC charge 8.5cm away?
Answer:
Force,
[tex]F = \frac{kQ_{1} Q_{2} }{ {r}^{2} } \\ F = \frac{(9 \times {10}^{9}) \times (25 \times {10}^{ - 6}) \times (10 \times {10}^{ - 6} ) }{ {(0.85)}^{2} } \\ \\ F = 3.114 \: newtons[/tex]
The magnitude of the force between a 25μC charge exerts on a -10μC charge 8.5cm away would be 311.4 N.
What is Coulomb's Law?Coulomb's law can be stated as the product of the charges and the square of the distance between them determine the force of attraction or repulsion acting in a straight line between two electric charges.
The math mathematical expression for the coulomb's law given as
F= k Q₁Q₂/r²
where F is the force between two charges
k is the electrostatic constant which is also known as the coulomb constant,it has a value of 9×10⁹
Q₁ and Q₂ are the electric charges
r is the distance between the charges
As given in the problem two charges a 25μC charge exerts on a -10μC charge 8.5cm away
By substituting the respective values in the above formula of Coulomb law
F =9×10⁹×(25×10⁻⁶)×(-10×10⁻⁶)/(8.5×10⁻²)²
F= -311.4 N
A negative sign represents that the force is attractive in nature
Thus, the magnitude of the force is 311.4 N.
Learn more about Coulomb's law from here
https://brainly.com/question/506926
#SPJ2
Use the values from PRACTICE IT to help you work this exercise. If the current in each wire is doubled, how far apart should the wires be placed if the magnitudes of the gravitational and magnetic forces on the upper wire are to be equal
I need help on Weight vs mass.
The difference between mass and weight is that mass is the amount of matter in a material, while weight is a measure of how the force of gravity acts upon that mass. Mass is the measure of the amount of matter in a body. Usually, the relationship between mass and weight on Earth is highly proportional; objects that are a hundred times more massive than a one-liter bottle of soda almost always weigh a hundred times more-approximately 1,000 newtons, which is the weight one would expect on Earth from an object with a mass slightly greater than 100 kilograms. In common usage, the mass of an object is often referred to as its weight, though these are in fact different concepts and quantities. In scientific contexts, mass is the amount of "matter" in an object (though "matter" may be difficult to define), whereas weight is the force exerted on an object by gravity. In other words, an object with a mass of 1.0 kilogram weighs approximately 9.81 newtons. Weight and mass are considered to be the same quantities. But many people tend to misuse these terms in their daily conversations. The main difference between weight and mass is that weight is the force of gravity by which the earth attracts towards it whereas mass is the amount of matter in an object.
the mass of an object is 10 kg and the velocity is 4 m/s, what is the momentum?
The answer is 40 kg. m/s.
Formula for momentum:
p=mv
p=(10 kg.)(4 m/s)
So, therefore, the final answer is p=40 kg. m/s.
I hope this helped answer your question. Enjoy your day, and take care!
Answer: its 400 n/s
Explanation:
cus my thing said it was right
As part of a NASA experiment, golfer Tiger Woods drives a golf ball on the moon, where g = 1.60 m/s2. He launches a golf ball with a speed of 285 km/h, at an angle of 42° with the horizontal. What horizontal distance will his drive travel before landing back on the surface of the moon. Ignore the curvature of the moon.
Answer:
Horizontal distance, R = vo2 sin(2x45)/g
v = 285 km/h = 79.17 m/s
R = 79.172 x 1/1.6
R = 3917 m
R = 3.9 km
Tiger Woods' golf ball will travel approximately 3925.22 meters horizontally before landing back on the surface of the moon.
To find the horizontal distance traveled by the golf ball on the moon, we can use the following kinematic equation:
d =[tex](v^2 * sin(2\theta)) / g[/tex]
where:
d = horizontal distance traveled
v = initial velocity of the golf ball (converted to m/s)
θ = launch angle
g = acceleration due to gravity on the moon (1.60 m/s²)
First, we need to convert the initial velocity from km/h to m/s:
Initial velocity (v) = 285 km/h = 285 * (1000 m/km) / (3600 s/h) ≈ 79.17 m/s
Now, plug the values into the equation:
d = ([tex]79.17^2[/tex]* sin(2 * 42°)) / 1.60
Calculate the value within the parentheses first:
sin(2 * 42°) = sin(84°) ≈ 0.999
Now, calculate the horizontal distance (d):
d = [tex](79.17^2 * 0.999) / 1.60[/tex]
d ≈ 3925.22 meters
So, Tiger Woods' golf ball will travel approximately 3925.22 meters horizontally before landing back on the surface of the moon.
To know more about horizontal distance, here
brainly.com/question/10093142
#SPJ2
A river is 87. meters wide and its current flows northward at 6 meters per second. A boat is launched with a velocity of 1.0 meters per second eastward from the west bank of the river. Determine the magnitude and direction of the boat’s resultant velocity as it crosses the river.
Answer:
explained
Explanation:
If a person rows a boat across a rapidly flowing river and tries to head directly for the other shore, the boat instead moves diagonally relative to the shore, as in Figure 1. The boat does not move in the direction in which it is pointed. The reason, of course, is that the river carries the boat downstream. Similarly, if a small airplane flies overhead in a strong crosswind, you can sometimes see that the plane is not moving in the direction in which it is pointed, as illustrated in Figure 2. The plane is moving straight ahead relative to the air, but the movement of the air mass relative to the ground carries it sideways.
A boat is trying to cross a river. Due to the velocity of river the path traveled by boat is diagonal. The velocity of boat v boat is in positive y direction. The velocity of river v river is in positive x direction. The resultant diagonal velocity v total which makes an angle of theta with the horizontal x axis is towards north east direction.
Figure 1. A boat trying to head straight across a river will actually move diagonally relative to the shore as shown. Its total velocity (solid arrow) relative to the shore is the sum of its velocity relative to the river plus the velocity of the river relative to the shore.
An airplane is trying to fly straight north with velocity v sub p. Due to wind velocity v sub w in south west direction making an angle theta with the horizontal axis, the plane’s total velocity is thirty eight point 0 meters per seconds oriented twenty degrees west of north.
Figure 2. An airplane heading straight north is instead carried to the west and slowed down by wind. The plane does not move relative to the ground in the direction it points; rather, it moves in the direction of its total velocity (solid arrow).
In each of these situations, an object has a velocity relative to a medium (such as a river) and that medium has a velocity relative to an observer on solid ground. The velocity of the object relative to the observer is the sum of these velocity vectors, as indicated in Figure 1 and Figure 2. These situations are only two of many in which it is useful to add velocities. In this module, we first re-examine how to add velocities and then consider certain aspects of what relative velocity means.
How do we add velocities? Velocity is a vector (it has both magnitude and direction); the rules of vector addition discussed in Chapter 3.2 Vector Addition and Subtraction: Graphical Methods and Chapter 3.3 Vector Addition and Subtraction: Analytical Methods apply to the addition of velocities, just as they do for any other vectors. In one-dimensional motion, the addition of velocities is simple—they add like ordinary numbers. For example, if a field hockey player is moving at 5 m/s
straight toward the goal and drives the ball in the same direction with a velocity of 30 m/s
relative to her body, then the velocity of the ball is 35 m/s
relative to the stationary, profusely sweating goalkeeper standing in front of the goal.
In two-dimensional motion, either graphical or analytical techniques can be used to add velocities. We will concentrate on analytical techniques. The following equations give the relationships between the magnitude and direction of velocity (
The figure shows components of velocity v in horizontal vx and in vertical y axis v y. The angle between the velocity vector v and the horizontal axis is theta.
Figure 3. The velocity, v, of an object traveling at an angle θ to the horizontal axis is the sum of component vectors and
These equations are valid for any vectors and are adapted specifically for velocity. The first two equations are used to find the components of a velocity when its magnitude and direction are known. The last two are used to find the magnitude and direction of velocity when its components are known.
Light of a given wavelength is used to illuminate the surface of a metal, however, no photoelectrons are emitted. In order to cause electrons to be ejected from the surface of this metal you should: ___________
a. use light of the same wavelength but increase its intensity.
b. use light of a shorter wavelength.
c. use light of the same wavelength but decrease its intensity.
d. use light of a longer wavelength.
Answer:
use light of the same wavelength but decrease it's intensity
Solar System - Scaling. When you look at Neptune in a telescope, you are actually looking into the past as the light has to travel from Neptune to your eyes. If the speed of light is ~300,000 km/s, how far back into the past are you looking (or put another way, how long does it take light to travel from Neptune to your eyes on Earth)
Answer:
Distance from sun to Neptune = 4.495E9 km
Time for light to travel = 4.495E9 / 3E5 sec = 14,980 sec
That is from sun to Neptune time fof light = 250 min
Time for light to travel from sun to earth is about 8 min
So the time from Neptune would be 242 to 258 min depending on position of Neptune - Note that Neptune is about 30X as far from the sun as earth and
250 min / 8 min is roughly 30
The uniform motion of kinematics allows us to find the time it takes for light to arrive from Neptune to Earth, which varies between:
t₁ = 1.45 10⁴ s and t₂₂= 1.55 10⁴ s
depending on the relative distance of the two planets
given parameters
The speed of light c = 300,000 km / s = 3 10⁸ m / s The distance from Neptune to Sum
to find
The time when light arrives from Neptune to Earth
They velocit of an electromagnetic wave is constant, so we can use the uniform motion relationships
v = d / t
t = d / v
where v is the speed of light, d the distance and y time, in this case the speed of the wave is the speed of light (v = c)
We look in the tables for the distances and the rotation periods around the sun
distance ( m) period (s)
Sun Neptunium 4.50 10¹² 5.2 10⁹
Sun - Earth 1.5 10¹¹ 3.2 10⁷
With the data of the period it is observed that the rotation of Neptune is much greater than that of Eart rotation around the sun, for which we will assume that Neptunium is fixed in space and the Earth may be in its aphelion or perihelion, maximum approach o away distance from the sun, consequently we calculate the time for the two cases:
Maximum approach
positions relative distance from the dos Plantetas is
Δd = [tex]x_{Neptuno - Sum} - x_{Earth - Sum}[/tex]d
Δd = 4.50 10¹² - 1.5 10¹¹
Δd = 43.5 10¹¹ m
the time it takes for Neptune's light to reach Earth is
Δt = [tex]\frac{ 43.5 \ 10^{11} }{3 \ 10^8}[/tex]
Δt = 14.5 10³ s
Δt = 1.45 10⁴ s
We reduce to hours
Δt = 1.45 10⁴ s (1 h / 3600 s) = 4.03 h
Maximum away
Δd = [tex]x_{Neptune - Sum} + x_{Neptune-Sum}[/tex]
Δd = 4.50 10¹² + 1.5 10¹¹
Δd = 46.5 10¹¹
The time is
Δt = [tex]\frac{46.5 \ 10^{11}}{ 3 \ 10^8}[/tex]
Δt = 15.5 10³
Δt = 1.55 10⁴ s
We reduce to hours
Δt = 1.55 10⁴ s (1 h / 3600 s) = 4.31 h
In conclusion, the time it takes for light to arrive from Neptune to Earth varies between:
t₁ = 1.45 10⁴ s and t₂ = 1.55 10⁴ s
depending on the relative distance of the two plants
learn more about the speed of light here: https://brainly.com/question/14355103
A mass is hanging from the end of a horizontal bar that pivots around an axis through its center, but it is being held stationary. The bar is then released and begins to rotate. As the bar rotates from horizontal to vertical, the magnitude of the torque on the bar: ________
Answer:
The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.
The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.
What is the difference between atomic number and atomic mass ?Atomic number of an element is defined as total number of protons present in the nucleus, neutrons carry no net electrical charge, so it is the charge number of the nucleus.
atomic mass of an element can be defined as the atomic weight is measured total mass of an element’s atom, the total number of neutrons and protons in the nucleus of an atom.
Both Atomic mass and an atomic number of elements are closely related if atomic number is high, then the atomic mass is also said to be high.
For more details regarding fire mass , visit
brainly.com/question/16858932
#SPJ2
Air is compressed polytropically from 150 kPa, 5 meter cube to 800 kPa. The polytropic exponent for the process is 1.28. Determine the work per unit mass of air required for the process in kilojoules
a) 1184
b) -1184
c) 678
d) -678
Answer:
wegkwe fhkrbhefdb
Explanation:B
An object starts from rest with constant acceleration of 8m/s2
along a straight line. Find The distance travelled during the 5th second.
Using second equation of kinematics
[tex]\boxed{\sf s=ut+\dfrac{1}{2}at^2}[/tex]
[tex]\\ \qquad\quad\sf{:}\dashrightarrow s=0(5)+\dfrac{1}{2}(8)(5)^2[/tex]
[tex]\\ \qquad\quad\sf{:}\dashrightarrow s=4(25)[/tex]
[tex]\\ \qquad\quad\sf{:}\dashrightarrow s=100m[/tex]
Why are scientific models important?
Answer:
Scientific models are representations of objects, systems or events and are used as tools for understanding the natural world. Models use familiar objects to represent unfamiliar things. Models can help scientists communicate their ideas, understand processes, and make predictions.
Infrared and ultraviolet waves have different frequencies.
Both types of wave can have harmful effects on human beings.
Describe the harmful effects of infrared and ultraviolet waves, relating them to the frequencies of the waves.
Answer:
For infrared and ultraviolet waves have different frequencies. Both types of wave can have harmful effects on human beings. Describe the harmful effects of infrared and ultraviolet waves, relating them to the frequencies of the waves. Medical studies indicate that prolonged IR exposure can lead to lens, cornea and retina damage, including cataracts, corneal ulcers and retinal burns, respectively. To help protect against long-term IR exposure, workers can wear products with IR filters or reflective coatings.When you look at the EM spectrum, UV waves are quite a bit smaller in wavelength than infrared, and x-rays/gamma rays are even smaller. Therefore, UV waves are probably causing more harm than infrared waves, and x-rays/gamma rays are probably doing even more damage.
Thank You
Please mark me Brainliest
Infrared and ultraviolet waves have different frequencies. Infrared waves have lower frequencies and longer wavelengths, while ultraviolet waves have higher frequencies and shorter wavelengths.
Harmful effects of Infrared waves:
Infrared waves have lower frequencies and are often associated with heat radiation. Prolonged exposure to intense infrared radiation can lead to thermal burns and damage to the skin and eyes. Infrared radiation can also cause dehydration and overheating of the body, especially in hot environments. While infrared radiation is not as harmful as ultraviolet radiation, excessive exposure can still lead to health issues.
Harmful effects of Ultraviolet waves:
Ultraviolet waves have higher frequencies and shorter wavelengths, making them more energetic than infrared waves. UV radiation from the sun is a well-known harmful agent. Short-term exposure to intense UV radiation can cause sunburn, skin redness, and eye irritation. Long-term exposure to UV radiation can lead to more serious health problems such as skin aging, cataracts, and an increased risk of skin cancer. UV radiation can also damage DNA in skin cells, leading to mutations and potential carcinogenesis.
It is essential to protect ourselves from both infrared and ultraviolet waves to prevent harmful effects. Using sunscreen and wearing protective clothing can help shield the skin from UV radiation. Limiting exposure to intense sources of infrared radiation, such as hot objects or infrared heaters, can help reduce the risk of thermal burns and overheating. Understanding the differences in the frequencies of these waves allows us to implement appropriate safety measures and protect our health.
To learn more about Infrared and ultraviolet waves, here
https://brainly.com/question/3091095
#SPJ2
M
A boy of mass 60 kg and a girl of mass 40 kg are
together and at rest on a frozen pond and push
each other apart. The girl moves in a negative
direction with a speed of 3 m/s. What must be the
total final momentum of the boy AND girl
combined?
A. -120 kgm/s
B. 0 kgm/s
C. -100 kgm/s
D. 120 kgm/s
Answer:
option D thinking so
Explanation:
okay na your whish
A sports car accelerates uniformly from rest to 24 m/s in 6 seconds. Calculate the acceleration of the car
Answer:
a = 4m/s^2
Explanation:
Velocity(V) = uniform = 24m/s
time(t) = 6sec
Acceleration(a) = V/t
= 24/6
= 4m/s^2
When a sports car accelerates uniformly from rest to 24 m/s in 6 seconds,then acceleration of the car would be 4 m/s²
What are the three equations of motion?There are three equations of motion given by Newton
The first equation is given as follows
v = u + at
the second equation is given as follows
S = ut + 1/2×a×t²
the third equation is given as follows
v² - u² = 2×a×s
Note that these equations are only valid for a uniform acceleration.
As given problem sport car accelerates uniformly from rest to 24 m/s in 6 seconds then the acceleration of the car can be calculated by using the first equation of motion
v = u + at
As given the initial velocity u= 0
The final velocity v = 24 m/s
The time taken is t= 6 seconds
By substituting the respective values of velocity and time
24 = 0+ a*6
a = 24/6
a = 4 m/s²
Thus, when a sports car accelerates uniformly from rest to 24 m/s in 6 seconds,then acceleration of the car comes out to be 4 m/s²
Learn more about equations of motion from here
brainly.com/question/5955789
#SPJ2
two thin lenses with the focal length of magnitude 15.0 cm . the first is diverging and second is converging lens are located 11.3 cm apart. an object 1.60 mm tall is placed 25 cm to the left of the first diverging lens. how far the first lens is the final image is formed?
is the final image is real or virtual?
what is the height of image?
Answer:
grandson annual Iranian Jamal Jamal Hannah travel
Serena wants to play a trick on her friend Marion. She adds salt, sugar, and vinegar into her glass of water when Marion is out of the room. Why does she know that Marion will drink the water?
Polarized sunglasses:
a. block most sunlight because sunlight is polarized
b. are better but work the same way as non-polarized sunglasses
c. are polarized to filter out certain wavelengths of light
d. block reflected light because reflected light is partially polarized.
Polarized sunglasses creates filter of vertical openings for light. The light rays will reach the eyes of human vertically only.
The sun rays will not reach human eye directly which will create a shield for sun light burden on human eye.
Polarized sunglasses are best used for blocking and eliminating certain wavelengths of light.
Therefore the correct answer is option C. Polarizes Sunglasses are polarized and it filter out certain wavelengths of light.
Learn more at https://brainly.com/question/24372632
the specific heat capacity of a substance is 500J/kg/oC. Find the heat required to rise the temperature of 10 quintial of the substance by 3 degree celcius
[tex]\boxed{\sf Q=mc\Delta T}[/tex]
[tex]\\ \sf\longmapsto Q=1000(5000)(3)[/tex]
[tex]\\ \sf\longmapsto Q=15000000J[/tex]
[tex]\\ \sf\longmapsto Q=1.5\times 10^7J[/tex]
what are the property of the image formed by plane mirror
of class 10
Answer:
» The image is laterally inverted.
» The image is upright.
» The image geometry is same as object geometry.
» Image distance is same as object distance.
» Image is not real, it's virtual ( not formed on screen ).
[tex].[/tex]
An object with a mass of 15 kg has an acceleration of 4 m/s2, what is the resultant force
F = m • a
F = (15 kg) • (4 m/s^2)
F = 60 Newtons
NOTE:
That's NOT a "resultant force".
That's the force you have to EXERT on 15 kg to MAKE it accelerate at 4 m/s^2 .
Using Newton second law
[tex]\\ \sf \longmapsto Force=Mass\times Acceleration[/tex]
[tex]\\ \sf \longmapsto Force=15(4)[/tex]
[tex]\\ \sf \longmapsto Force=60N[/tex]
