Answer:
I Don't know
Explanation:
Because I'm 5 grade student
7) A force of 500N exists between two identical point charges separated by a dis-
tance of 40 cm the magnitude of the two charges is
Answer:
q=9.43×10^-5C
Explanation:
F=kq^2/r^2
500= 9×10^9 × q^2/ (0.4)^2
500N×0.16m=9×10^9Nm^2C^2 × q^2
80/(9×10^9)= q^2
√(8.8889×10^9) = q
q= 9.43×10^-5C
since they are identical both charges, q=9.43×10^-5C
The magnitude of the two charges is 9.43×10^-5 C.
To calculate the magnitude of an electric force, it is necessary to use the following expression:
[tex]F = k \frac{q_{1} \times q_{2} }{d^{2}}[/tex]
Assuming that the constant is:
[tex]k = 9\times 10^{9}[/tex]
We can apply the values in the formula above, obtaining:
[tex]500 = 9 \times 10^{9} \times \frac{q^{2}}{0.4^{2}}[/tex]
[tex]q = \sqrt{0.88\times10^{-8}}[/tex]
[tex]q = 9.43 \times 10^{-5} C[/tex]
So, the magnitude of the two charges is 9.43×10^-5 C.
Learn more about electrical force in: brainly.com/question/16888648
the treasure map gives the following directions to the buried treasure
Answer:
North
South
East
West
Explanation:
please mark me as brainliest
What is a benefit of joining the YMCA instead of a private health club?
The YMCA has nicer equipment and buildings.The YMCA has nicer equipment and buildings. , ,
The YMCA is likely to be in an upscale neighborhood.The YMCA is likely to be in an upscale neighborhood. , ,
The YMCA is much more affordable.The YMCA is much more affordable. , ,
The YMCA has restaurants and spa services.
Answer:
Explanation:
This depends on where you are.
The YMCA where I grew up was affordable. Very. Or my mother would not have let me go.
A cylinder is given a push and then rolls up an inclined plane. If the origin is the starting point, sketch the position, velocity, and acceleration of the cylinder vs. time as it goes up and then down the plane.
Current is the rate at which charge is flowing.
a. True
b. Fals
Answer:
A. True
Explanation:
What is tensor quantity?
Is Inertia a tensor? give reason
Answer:
A tensor is a quantity, for example a stress or a strain, which has magnitude, direction, and a plane in which it acts. Stress and strain are both tensor quantities. ... A tensor is a quantity, for example a stress or a strain, which has magnitude, direction, and a plane in which it acts.
Inertia Tensor. where I = the inertia tensor. The angular momentum of a rigid body rotating about an axis passing through the origin of the local reference frame is in fact the product of the inertia tensor of the object and the angular velocity. ... As shown in [7], the inertia tensor is symmetric.
Explanation:
Hope dis help
The theory of the origin of the universe that is most popular among space scientists suggests that our universe originated how long ago
10-20 million years ago
10-20 trillion years ago,
10-20 billion years ago
10-20 thousand years ago
Answer:
10 - 20 million years ago
Good evening everyone Help me i n my hw ,The wall of cinema hall are covered with sound absorbing materials. Why?Answer it ASAP.Good day
what do you mean about it
Describe the forces that act on a skydiver before
and after the parachute is opened.
I will give brainliest!!!!
Answer:
Before the parachute opens: Immediately on leaving the aircraft, the skydiver accelerates downwards due to the force of gravity. There is no air resistance acting in the upwards direction, and there is a resultant force acting downwards. The skydiver accelerates towards the ground.
Once the parachute is opened, the air resistance overwhelms the downward force of gravity. The net force and the acceleration on the falling skydiver is upward. An upward net force on a downward falling object would cause that object to slow down. The skydiver thus slows down.
I HOPE THIS WILL HELP YOU IF NOT THEN SORRYHAVE A GREAT DAY :)
2. The vector sums of and the Ark witar must se rue our the directions and maintedes at an Bit CB? What meast le tue about the directions and magnitudes and it cor
Check attached photo
Check attached photo
Sound is an example of a:
Select one:
O a. rolling waves
b. longitudinal wave
O c. traverse waves
O d. surface wave
Ez Physics question will mark brainliest.
Answer:
The answer is B. longitude wave
A 10 n force is applied horizontally on a box to move it 10 m across a frictionless surface. How much work was done to move the box?
Answer:
[tex]\boxed {\boxed {\sf 100 \ J}}[/tex]
Explanation:
We are asked to calculate the work done to move a box.
Work is the product of force and distance or displacement.
[tex]W= F*d[/tex]
A 10 Newton force is applied horizontally on the box. Since the surface is frictionless, there is no force of friction, and the net force is 10 Newtons. The force moves the box 10 meters.
F= 10 N d= 10 mSubstitute the values into the formula.
[tex]W= 10 \ N * 10 \ m[/tex]
Multiply.
[tex]W= 100 \ N*m[/tex]
Let's convert the units. 1 Newton meter is equal to 1 Joule, therefore our answer of 100 Newton meters is equal to 100 Joules.
[tex]W= 100 \ J[/tex]
100 Joules of work was done to move the box.
Help please!!!!!!!!! I will mark brainliest!!!
Answer:
solving for: velocity
equation: velocity = distance / time
substitution: velocity = 1425 km / 12.5 hrs
answer: 114 km/hr
Our system is a block attached to a horizontal spring on a frictionless table. The spring has a spring constant of 4.0 N/m and a rest length of 1.0 m, and the block has a mass of 0.25 kg.
Compute the PE when the spring is compressed by 0.50 m.
Answer
E - 1/2 K x^2 potential energy of compressed spring
E = 1/2 * 4 N / m * (.5 m)^2 = 2 * .5^2 N-m = .5 N-m
The kinetic energy of a particle of mass 500g is 4.8j. Determine the velocity of the particle
Answer:
4.38 m/s
Explanation:
What is the submarine's maximum safe depth in sea water? The pressure inside the submarine is maintained at 1.0 atm
Answer:
The submarine's maximum safe depth in sea water is 801.678 m.
Explanation:
P=Po+(rho)*g*h
Max Pressure = Initial Pressure + (Water Density)(Gravity)(Max Depth)
Area of Window = Pi*(Diameter/2)^2 = Pi*(.4m/2)^2 = 0.125664 m^2
Max Pressure= (1.0*10^6 N)/(0.125664 m^2)= 7.95775-E6 Pa
Initial Pressure= 1atm= 101.3kPa= 101300Pa
Water Density (rho) = 1000kg/m^3
Gravity= 9.8m/s^2
So rearranging for h= (P-Po)/((rho)*g)
h=((7.95775-E6Pa)-(101300Pa))/((1000kg/m^3)(9.8m/s^2))= 801.678 m
Which item will be shipped third?
—-
Answer:
I know it's groceries
Explanation:
electronics ship before clothing
electronics ship after groceries
urgent items are first so
order:
1.) A/Electronics
2.) Clothing/B
3.) Groceries(since groceries aren't urgent)
thing is it's C or D I'm leaning to D since it says it ships last but i dont know so if I'm wrong sorry.
calculate the rate of loss of heat through a glass window of area 200 CM square and thickness 0.5 CM where temperature inside is 35 degree Celsius and outside is -5 degree Celsius conductivity of Glass is 2.2 into 10 to the power 3 cal per s per cm per k .
Answer:
The inner and outer surfaces of a 0.5-cm thick 2-m by 2-m window glass in winter are 10°C and 3°C, respectively. If the thermal conductivity of the glass
Explanation:
what Is accuracy ............
Answer:
Accuracy is how much the consequence of an estimation adjusts to the right worth or a norm' and basically alludes to how close an estimation is to its concurred esteem
《OAmalaOHopeO》
Answer:
In a set of measurements, accuracy is closeness of the measurements to a specific value, while precision is the closeness of the measurements to each other.
Explanation:
_Hope it helps you_
A 50.0 ohm and a 30.0 ohm resistor are connected in parallel. What is their equivalent resistance? Unit=Ohms
R(parallel) = product/ sum
50×30/50+30
1500/80
18,75 ohms
Answer: 18.75
above is right but you need to put a dot after the number 18
A plastic box with objects has a mass of 4 kg and is on a shelf at a height of 2.4 m. What will it's potential gravitational energy?
Answer:
potential energy=mgh
4×9.8×2.4
Explanation:
may be hope this will help you
The pressure of sea water increases by 1.0atm for each 10m increase in the depth, by what percentage is the density of water increased in the deepest ocean of water of 12km. Compressibility is 5.0×10^-5 atm
The percentage by which the water density increased is 4.1[tex]\mathbf{\overline 6}[/tex] %
The known values are;
The increase in pressure per 10 meter increase in depth = 1.0 atm
The depth of the deepest ocean = 12 km = 12,000 m
The compressibility of the ocean = 5.0 × 10⁻⁵ 1/atm
The unknown
The percentage the density of water increased in the deepest ocean
Strategy;
Find the pressure at the deepest point of the deepest ocean and apply the compressibility
We have;
[tex]\mathbf{Compressibility = \dfrac{1}{V} \times \dfrac{\partial V}{\partial p}}[/tex]
The change in pressure, [tex]\partial p[/tex] = (12,000 m/(10 m)) × 1.0 atm = 1,200 atm
Therefore, we have for one cubic meter of water
[tex]\mathbf{5.0 \times 10^{-5} \ atm^{-1} = \dfrac{1}{1 \, m^3} \times \dfrac{\partial V}{1,200 \, atm}}[/tex]
Therefore;
[tex]\mathbf{\partial}[/tex]V = 5.0 × 10⁻⁵ atm⁻¹ × 1 m³ × 1,200 atm = 0.06 m³
The new volume = V - [tex]\mathbf{\partial}[/tex]V
∴ The new volume = 1 m³ - 0.06 m³ = 0.94 m³
The initial density = mass/(1 m³)
The new density = mass/(0.96 m³)
The percentage increase in density, [tex]\partial[/tex]ρ%, is given as follows;
[tex]\mathbf{\partial p \% = \dfrac{ \dfrac{Mass}{0.96 \ m^3} - \dfrac{Mass}{1 \ m^3} }{ \dfrac{Mass}{1 \ m^3}} \times 100 = \dfrac{25}{6} \% = 4.1 \overline 6 \%}[/tex]
∴ [tex]\mathbf{\partial}[/tex]ρ% = 4.1[tex]\mathbf {\overline 6}[/tex] %
The percentage by which the water density increased, [tex]\partial[/tex]ρ% = 4.1[tex]\mathbf{\overline 6}[/tex] %
Learn more about compressibility here;
https://brainly.com/question/18746977
A stone that is dropped freely from rest traveled half the total height in the last second. with what velocity will it strike the ground
Answer:
hellooooo :) ur ans is 33.5 m/s
At time t, the displacement is h/2:
Δy = v₀ t + ½ at²
h/2 = 0 + ½ gt²
h = gt²
At time t+1, the displacement is h.
Δy = v₀ t + ½ at²
h = 0 + ½ g (t + 1)²
h = ½ g (t + 1)²
Set equal and solve for t:
gt² = ½ g (t + 1)²
2t² = (t + 1)²
2t² = t² + 2t + 1
t² − 2t = 1
t² − 2t + 1 = 2
(t − 1)² = 2
t − 1 = ±√2
t = 1 ± √2
Since t > 0, t = 1 + √2. So t+1 = 2 + √2.
At that time, the speed is:
v = at + v₀
v = g (2 + √2) + 0
v = g (2 + √2)
If g = 9.8 m/s², v = 33.5 m/s.
Cho các máy cắt sử dụng trong công nghiệp có ký hiệu trên nhãn thiết bị: C350; B500. Hãy tính dòng điện bảo vệ ngắn mạch và dòng điện bảo vệ quá tải của từng thiết bị?
Answer:
ask in the English then I can help you
Explanation:
please mark me as brain list
can you guys pls also solve for average speed.
Answer:
d_t = 3.05km
v_a = 4.3km/h
Explanation:
42mins*(2/3) = 28mins
42mins-28mins = 14mins
d = v*t
d_1 = (4km/h)*(1h/60mins)*(28mins)
d_1 = 1.87km
d_2 = (5km/h)*(1h/60mins)*(14mins)
d_2 = 1.17km
d_t = d_1+d_2
d_t = 1.87km+1.17km
d_t = 3.05km
v_a = (v_1+v_2)/2
v_a = [(2*4km/h)+5km/h)]/3
v_a = 4.3km/h
What would happen if you changed the position of the screen, but kept the other factors the same?
Answer:
I wish I could help but iam srry
1) Un objeto realiza un movimiento circular uniforme en una circunferencia de 10 metros de diámetro y efectúa 20 vueltas por minuto. Se pide hallar:
a) El periodo.
b) La frecuencia en Hertz.
c) La velocidad tangencial. d) La velocidad angular.
e) La aceleración centrípeta.
Answer:
A RECIPE NEEDS A COMBINED WEIGHT OF 720G OF FLOUR AND SUGAR. IF THE RECIPE NEEDS 5TIME FLOUR THAN SUGAR,HOW MUCH OF EACH IS NEEDED
A liquid is poured into a vessel to a depth of 16cm when viewed from the top, the bottom appears to be raised 4cm. What is the refractive index of the liquid?
Answer:
Solution
Verified by Toppr
Correct option is
C
3 cm
RI=apparent depthreal depth
Substituting, 34=apparentdepth12
Therefore, apparent depth=412×3=9
The height by which it appears to be raised is 12−9=3cm
Was this answer helpful?
71
0
SIMILAR QUESTIONS
A coin is placed at the bottom of a glass tumbler and then water is added. It appeared that the depth of the coin has been reduced because
Medium
View solution
>
A tank is filled with water to a height of 12.5 cm. The apparent depth of a needle lying at the bottom of the tank is measured by a microscope to be 9.4 cm. What is the refractive index of water? If water is replaced by a liquid of refractive index 1.63 up to the same height, by what distance would the microscope have to be moved to focus on the needle again?
14. If you are asked to analyze an issue for an essay assignment, what should you do? a. Nb. C. Divide the issue into its main parts and discuss each part. Express your opinion about the issue. Explain what you think the issue means and how you came to that interpretation Describe the main ideas or points about the issue. d.
Answer:
Option C
Explanation:
Divide the issue into its main parts and discuss each part.
A student graphs power (p) on the vertical axis and time (t) on the horizontal axis. The graph appears to be a hyperbola.
a) What should the student graph on each axis to test whether the relationship is actually
hyperbolic?
b) If the relationship is actually hyperbolic, what is the general equation for the relationship between power and time?
Answer: it would be daddy
Explanation:
Because I’m daddy
