The causes of low compression in an engine cylinder and leakage past the exhaust can be identified by performing mechanical tests on the engine
The correct technician is Tech B; Blown head gasket would generally leak past the exhaust valve
The reason for arriving at the above selection is as follows:
A cylinder leakage test is generally performed after there is an indication of low compression from one or more cylinders. The test allows the identification of the part of the cylinder that is leaking.
The cylinder that shows sign of low compression is often the location that the cylinder leakage test is performed, although, the test can be performed on every cylinder
A cylinder leakage test is valid only when
The temperature of engine is about the temperature range of the engine in operationThe cylinder under test is at the Top Dead Center (TDC) position, such that the position of the piston in the cylinder is at the top or highest point of its strokeTherefore, the positioning of the piston in the bottom dead center during a leakage test as mentioned by Tech A is not correct
The route of coolant in the engine are sealed by the cylinder head gasket, where there is a blown head gasket, the coolant will be allowed to leak into the cylinders and into the exhaust, causing white smoke and sweet odor of antifreeze
Therefore, Tech B is correct, coolant leakage into the exhaust is an indication of a blown head gasket
Learn more about engine mechanical testing here:
https://brainly.com/question/14639903
Solve using Matlab the problems:
One using the permutation of n objects formula
One using the permutation of r objects out of n objects
You can pick these problems from the textbook or you can make up your own questions.
Help me pleaseeeee
Answer:
Explanation:
% Clears variables and screen
clear; clc
% Asks user for input
n = input('Total number of objects: ');
r = input('Size of subgroup: ');
% Computes and displays permutation according to basic formulas
p = 1;
for i = n - r + 1 : n
p = p*i;
end
str1 = [num2str(p) ' permutations'];
disp(str1)
% Computes and displays combinations according to basic formulas
str2 = [num2str(p/factorial(r)) ' combinations'];
disp(str2)
=================================================================================
Example: check
How many permutations and combinations can be made of the 15 alphabets, taking four at a time?
The answer is:
32760 permutations
1365 combinations
==================================================================================
Report of invertor to convert 12 volt to 220 volt.
Can anyone help me ?
Question # 1
Fill in the Blank
Complete the following sentence.
Mobility refers to the ability to _____.
to move or walk freely and easly
At what depth in water is the increased pressure five times greater than atmospheric pressure (101 kPa)?
Explanation:
40.4m
Explanation:
Pressure at depth is given as
P = P, + pgh
Final pressure at depth h= 5 Po
5Po= Po + pgh
pgh = 4Po = 4 x 1.01 x 10^5
h = (4.04×10^5)/ (1000x10)
h=40.4m
What is the following diagram called?
Answer:
business
Explanation:
because shopping has great income
Answer:
is ur question right
Explanation:
is ur question right
is ur question right
“Snow Cover Area change Analysis for Kabul Basin”
Summarize how GIS & Remote Sensing is incorporated in this study.
GIS
The full for GIS is : Geographic Information System.
The GIS is a system of mapping that is used to create, analyze, manage and map all the types of data.
It is a method capturing, checking as well as displaying all the data that is related to the position of the surface of earth.
Remote Sensing
Remote sensing is defined as a process where the various physical characteristics of an area are constantly monitored and detected by a process of measuring the reflection of the emitted radiations at ta distance.
The snow covered areas of the Kabul basin can be monitored and analyzed by using the process of GIS and remote sensing.
They provide a continuous source of information and data about snow covered peaks, the amount of snow to the authorities.
Learn More :
https://brainly.in/question/1556256?__cf_chl_captcha_tk__=pmd_2d2d9994422ca43d3cbbcf6322e6c34da175405a-1628654009-0-gqNtZGzNAvijcnBszQ3i
The mass flow rate through a centrifugal compressor is 1 kg/s. If air enters at 1 bar and 288k and leaves at 200 kN/m² and 370k, determine the power of the compressor. Take Cp = 1.103 kJ (kg.K), R = 287 kJ (kg.k)
Answer:
Explanation:
That's the correct answer to the question , thanks
pls i need help with this
Solve using Matlab three problems:
One using the combination formula
One using the permutation of n objects formula
One using the permutation of r objects out of n objects
You can make up your own questions
Answer:
%%%%Problem 1%%%
while n<1:
c=(n!)/((n-r)!(r!))
end
%%end of solution 1%
What should you do first to best use your personal goals as a means for a promotion
Answer:
Explanation:
research how your company offers promotions show professional behavior at all times set both short and long-term personal goals make sure some goals are only for personal growth
sơ đồ nguyên lý của một hệ thống lạnh
Answer:
A = 5h (B + b); solve for B.
2
On Beverly's last project, the team identified only a few lessons learned. Which approach to lessons learned
can she implement on her current project to identify most of the lessons learned?
Select an answer.
reminding team members to be positive
providing an anonymous method for submitting lessons learned
making lessons learned a regular part of meetings
holding lessons learned meetings without managers present
Option C (making lessons learned a regular part of meetings) is the correct approach.
As nothing more than a general rule, typically construction companies only plan lessons that have been learned exercises or initiatives towards the end of a particular endeavor or segment.As almost a result of the team knowing, valuable lessons are intended to increase the comprehensive implementation of quality management practices as well as deadlines.
Aside from this, none of the choices are viable methods to learning lessons or gaining knowledge from the past. As a result, the methodology outlined above is the appropriate one.
Learn more about project teamwork here:
https://brainly.com/question/14279121
What is working fluid and mention five example of working fluid.
Answer:
For fluid power, a working fluid is a gas or liquid that primarily transfers force, motion, or mechanical energy. ... Examples without phase change include air or hydrogen in hot air engines such as the Stirling engine, air or gases in gas-cycle heat pumps, etc.
Explanation:
Answer:
A working fluid is a gas or liquid that primarily transfers force, motion or mechanical energy
Examples:Air, pentane, chlorofluorocarbons, butane, propane and ammonia
Why is logging done during drilling?
Answer:
Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible
what the different methods to turn on thyrister and how can a thyrister turned off
Answer:
forward voltage triggering
temperature triggering
dv/dt triggering
light triggering
gate triggering
Then turning off;
Turn off is accomplished by a "negative voltage" pulse between the gate and cathode terminals
Explanation:
hope it helps
If the tank is designed to withstand a pressure of 5 MPaMPa, determine the required minimum wall thickness to the nearest millimeter using the maximum-shear-stress theory. Apply a factor of safety of 1.5 against yielding.
Answer: hello some aspects of your question is missing below is the missing information
The gas tank is made from A-36 steel and has an inner diameter of 1.50 m.
answer:
≈ 22.5 mm
Explanation:
Given data:
Inner diameter = 1.5 m
pressure = 5 MPa
factor of safety = 1.5
Calculate the required minimum wall thickness
maximum-shear-stress theory ( σ allow ) = σγ / FS
= 250(10)^6 / 1.5 = 166.67 (10^6) Pa
given that |σ| = σ allow
3.75 (10^6) / t = 166.67 (10^6)
∴ t ( wall thickness ) = 0.0225 m ≈ 22.5 mm
R-744 refrigerant is bad why
Answer:
Explanation:
R-744 is seen as the 'perfect' natural refrigerant as it is climate neutral and there is not a flammability or toxicity risk. It is rated as an A1 from ASHRAE. While it is non-toxic there is still risk if a leak occurs in an enclosed area as R-744 will displace the oxygen in the room and could cause asphyxiation
I was asked a question in vibrations: What does the magnification factor (MF) magnify? Or why is it called the magnification factor?
Answer:
Is the ratio of new displacement of the vibration to the original displacement of the vibration
Explanation:
[tex]{ \boxed{ \bf{MF = \frac{X }{X _{0} } }}}[/tex]
Explain the LWD process why is it important in drilling operations?
Answer:
Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible.
Explanation:
pls mark brainliest
A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your response to this claim?
The claim will be impractical. The reason behind this is provided below throughout the explanation segment.
Inside the same combustion chamber, fresh water can't be pressurized even more than fuel as well as air. Consequently, the cylinder does not burn due to a problem with the compressor.To accomplish the development processes, a machine requires any sort of combustible which might cause combustion as well as create a tremendous quantity of power.
Thus, the idea of using water instead of petroleum appears unworkable throughout traditional engines.
Learn more:
https://brainly.com/question/4067583
Cho biết tác dụng chung của các hệ giằng khung ngang nhà công nghiệp nhẹ 1 tầng 1 nhịp.
what does mean setbacks with MRT station?
Biết op-amp có Vsat = 12V, R1=R2=R3=R4=R, dạng sóng điện áp Vi(t) được cho như
hình 2.16b
a. Tính V0 theo Vi, độ lợi áp AV
b. Vẽ lại dạng sóng điện áp V0(t) khi Vm= 3
8 V
c. Vẽ lại dạng sóng điện áp V0(t) khi Vm = 5V
Answer:
Hello bro
Explanation:
I think i can help you something but can you translate it on english plzz
theory for the determination of the Compressive strength of bricks?
Answer:
Compressive strength of bricks is the capacity of brick to resist or withstand under compression when tested on Compressive testing machine [CTM]. The Compressive strength of a material is determined by the ability of the material to resist failure in the form of cracks and fissure.
Explanation:
If you want to know more, refer to this link:
https://civilread.com/compressive-strength-test-on-brick/#:~:text=Compressive%20strength%20of%20bricks%20is,form%20of%20cracks%20and%20fissure.
what is the term Self-induced EMF (Induction)
Self induction and Mutual induction
If the current through the coil changes, the flux through the coil changes and an emf is induced. Since the emf is induced in the coil due to its own field, it is called self–induced emf and the phenomenon is called self–induction.
Answer:
Self induced EMF is the electro-motive force that is generated due to change in flux in the coil caused by the change in current in the same coil.
Question in Statistics and Probability 2
Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
State the Null and the Alternative Hypotheses.
Complex poles and zeros. Sketch the asymptotes of the Bode plot magnitude and phase for each of the listed open-loop transfer functions, and approximate the transition at the second-order break point, based on the value of the damping ratio. After completing the hand sketches, verify your result using Matlab.
L(s)= 1/s(s^2+ 3s+ 10)
The asymptotes of the open loop transfer are:
Horizontal: y = 0
Vertical: x = -10 and x = -100
How to plot the asymptotes?The open loop transfer function is given as:
f(s) = 100(s + 1)/((s + 10)(s + 100))
Set the numerator of the function to 0.
So, we have:
f(s) = 0/((s + 10)(s + 100))
Evaluate
f(s) = 0
This means that, the vertical asymptote is y = 0
Set the denominator of the function to 0.
(s + 10)(s + 100) 0
Split
s + 10 = 0 and s + 100 = 0
Solve for s
s = -10 and s = -100
This means that, the horizontal asymptotes are s = -10 and s = -100
See attachment for the graph of the asymptotes.
Therefore, The asymptotes of the open loop transfer are:
Horizontal: y = 0
Vertical: x = -10 and x = -100
Read more about asymptotes at:
brainly.com/question/4084552
#SPJ2
If OSHA determines that an employer's response to a non-formal complaint is adequate, what options does the employee filing the non-formal complaint have?
there are many different values associated with an AC sine wave which one of the following continually changes throughout the cycle?
A. instantaneous value
b. effective value
c. peak value
d. average value
A. The instantaneous value (of voltage for sure and also possibly of current) continually changes thought the cycle.
Sine waves are by far the most common type of alternating current waveform employed in electrical engineering. The correct option is A.
What are Sine Waves?Sine waves are by far the most common type of alternating current waveform employed in electrical engineering. An AC Waveform is the shape formed by charting the instantaneous ordinate values of either voltage or current against time.
There are many different values associated with an AC sine wave but the one that continually changes throughout the cycle is the instantaneous value.
Hence, the correct option is A.
Learn more about Sine Wave:
https://brainly.com/question/14979785
#SPJ2
Work to be performed can come from the work package level of the work breakdown structure as well as other sources. Which of these is NOT a source of authorized work to be performed?
a. Scope creep
b. Defect repairs
c. Preventive actions
d. Corrective actions
A project is meant to achieve clearly defined goals within present constraints
The correct option for the source of work in a project which is NOT a source of authorized work to be performed is option (a)
a. Scope creep
The reason for the selecting the above option is as follows;
In project management, alongside work planned in a work package, authorized work to be performed can come from;
The repairing of defects found in completed work and which is a requirement for the project to be approvePreventive actions, that are meant to mitigate factors that affect the project timeline and costCorrective actions which include actions meant to rectify parts of the project that produce an error outcomeA scope creep, however, is generally is due to the inclusion of the end
users of the project at a time that is behind schedule, insufficient analysis of
the requirements, and project complexity underestimation. and consists of
changes made after a project has commenced
A scope creep therefore, changes the amount of work to be done which
therefore alters the project timeline, and due to project, budgetary, and
end user constraints, CANNOT be a source of authorized work to be
performed
The correct option for the source that is NOT a authorized work to be performed is option a. Scope creep
Learn more about scope creep here:
https://brainly.com/question/14061926
