Answer:
A retaining of a wall is a protective structure, first and foremost.
Explanation:
Its main aim is to provide functional support for keeping soil in place. It acts as a wall to keep the soil on one side and the rest of the landscape area on the other, providing a platform for a garden to be created.
An engineer designing a vibration isolation system for an instrument console models the consoleand isolation system as a 1 degree-of-freedom spring-mass-damper system. The modeled mass is 2kg, the spring constant is 8 N/m, and the damping constant is 1 Ns/m. The system is exposed to atime-varying force acting on the mass. This force measured is approximated by:F(t) = 20 sin(4t) [N]. Determine the steady-state response of the system to this input.
Solution :
Given :
m = 2 kg
k = 8 N/m
C= 1 N-s/m
F(t) = 20 sin (4t)
[tex]$F_0= 20 \ N$[/tex]
ω = 4 rad/s
[tex]$\omega_n = \sqrt{\frac{k}{m}}$[/tex]
[tex]$\omega_n = \sqrt{\frac{8}{2}}$[/tex]
= 2 rad/s
Therefore,
[tex]$\epsilon = \frac{C}{2 m \omega_n}$[/tex]
[tex]$\epsilon = \frac{1}{2 \times 2 \times 2}$[/tex]
= [tex]$\frac{1}{8}$[/tex]
= 0.125
So, r = [tex]$\frac{\omega}{\omega_n}$[/tex]
= [tex]$\frac{4}{2}$[/tex]
= 2
Steady state response is given by
[tex]$(A)=\frac{F_0 / k}{\sqrt{(1-r^r)^2+(2 \epsilon r)^r}}$[/tex]
[tex]$(A)=\frac{20 / 8}{\sqrt{(1-2^r)^2+(2 \times 0.125 \times 2)^r}}$[/tex]
A = 0.82 m
Example 5 10, P 236 9th edition Refrigerant 134 a at 700 kPa , 70 deg C and 8 kg/min is cooled by water in a condenser until it exists as a saturated liquid at the same pressure. The cooling water enters the condenser at 300 kPa and 15 deg C and leaves at 25 deg C at the same pressure. Determine the mass flow rate of the cooling water required to cool the refrigerant.
Solution :
The mass flow rate of the cooling water is determined from the energy balance equation. The enthalpies of the refrigerant at the initial and the final states were obtained from A-13 and A-12 for the given parameters.
Therefore by energy balance equation,
[tex]$\dot m_r h_{r1}=\dot m_w \Delta h_w +\dot m_r h_{r2} $[/tex]
[tex]$\dot m_w = \frac{\dot m(h_1-h_2)_r}{c \Delta T}$[/tex]
[tex]$\dot m_w = \frac{8(308.34-88.82)}{4.18 \times 10}$[/tex]
= 42 kg / min
A chemical process converts molten iron (III) oxide into molten iron and carbon dioxide by using a reducing agent of carbon monoxide. The process allows 10.08 kg of iron to be produced from every 16.00 kg of iron (III) oxide in an excess of carbon monoxide. Calculate the percentage yield of iron produced in this process.
Answer:
percentage yield = 63%
Explanation:
The yield efficiency or percentage yield measure the amount of products that are formed from a given amount of reactant. For a percentage yield of 100, all the reactants are completely converted to product. Mathematically, the percentage yield is given by:
[tex]percentage\ yield = \frac{Actual\ yield}{expected\ yield} \times 100\\Actual\ yield = 10.08kg\\Expected\ yield= 16.00kg\\\\\therefore percentage\ yield = \frac{10.08}{16.00} \times 100 = 63 \%[/tex]
Which basic principle influences how all HVACR systems work?
A) A decrease in pressure increases the boiling point of liquid, the temperature at which the liquid turns to a gas.
B) An increase in pressure can lower the boiling point of a liquid and change the temperature at which it turns to a gas.
C) An increase in pressure can increase the boiling point of a liquid, the temperature at which the liquid turns to a gas.
D) Pressure affects boiling point and evaporation in an unpredictable way, so it must not be considered in HVACR equipment.
Answer:
B) An increase in pressure can lower the boiling point of a liquid and change the temperature at which it turns to a gas.
Explanation:
B) An increase in pressure can lower the boiling point of a liquid and change the temperature at which it turns to a gas.
The basic principle which influences how all HVACR systems work is that an increase in pressure can increase the boiling point of a liquid, the temperature at which the liquid turns to a gas. Thus, the correct option for this question is C.
What is an HVACR system?An HVACR system may be defined as a type of system that is significantly designed in order to achieve the environmental requirements of the comfort of occupants and a process. These systems are used in different types of buildings such as industrial, commercial, residential, and institutional buildings.
Heating, air conditioning, and refrigeration mechanics and installers, often called HVAC technicians, work on heating, ventilation, cooling, and refrigeration systems that control the temperature and air quality in buildings.
If you're interested in becoming qualified to install heating and cooling systems and you want to know more about the HVAC-R industry, read on for professional definitions and training options.
Therefore, the correct option for this question is C.
To learn more about the HVACR system, refer to the link:
https://brainly.com/question/29996270
#SPJ2
The entropy of the working fluid of the ideal Carnot cycle (increases, decreases, remains the same) during the isothermal heat rejection process. (Explain the reasoning behind your answer selection!)
Answer:
Decreases
Explanation:
The Entropy change for a reversible process is;
ΔS = nRIn(V_b/V_a)
Now, applying this formula to an isothermal expansion in an irreversible process, it will have same initial and final states as we got for the reversible expansion process. Now, due to the fact that entropy is a state function, the change in entropy of the system will be the same as we got for the equation in reversible process and is given by the same formula.
In both the reversible and irreversible process, the surroundings of which they differ by the entropy there are usually at a constant temperature, T in a way that we have the change jn entropy relationship as;
ΔS_sur = −Q/T
Where;
- the negative sign is used since the heat transferred to the surroundings is equal in magnitude and opposite in sign to the heat, Q, transferred to the system.
Thus, it is clear that the change in the entropy decreases due to the negative sign.
Which of the following is NOT a peripheral?
Input devices
Output devices
CPU devices
Input/Output devices
Answer:
I believe that cpu devices are not considered peripherals
Explanation:
From google: A peripheral or peripheral device is an ancillary device used to put information into and get information out of the computer.
What are the two tools used to create an HTML code? Name one example of each tool.
Answer:
please mark me as BRAINLIEST
Explanation:
There are so many software packages available to develop HTML. The software packages can be grouped into two main categories: text-based (or code-based) editors.
...
WYSIWYG editors
Macromedia Dreamweaver.
Microsoft FrontPage.
Adobe GoLive.
please I need dhelp asap
What is the shape of an airplane wing called?
air raid
airport
airfoil
Answer:
the answer is airfoil
Explanation:
hope the answer helps
Answer:
It is called the airfoil
Explanation:
The answer is D. ( airfoil) because an airport is a place. Air raid is a attack in the air and that only leaves airfoil, so airfoil is the correct answer.(Hoped that helped)
brainiest and 35 points for the RIGHT ANSWER
Which of the following devices is used to determine if an item is horizontal?
a level
a lever
a shank
a clamp
An electronic device, such as a power transistor mounted on a finned heat sink, can be modeled as a spatially isothermal object with internal heat generation and an external convection resistance. (a) Consider such system of mas M, specific heat c, and surface area As, which is initially in equilibrium with the environment at To. Suddenly, the electronic device is energized such that a constant heat generation Eg(W) occurs. Show that the temperature response of the device is: θ = exp RC where θ Ξ T-T(w): T(oo) is the steady-state temperature corresponding to t → oo; 0Ti T(; T: initial temperature of the device; R: thermal resistance 1/hAs; and C: thermal capacitance Mc. (b) An electronic device, which generates 60W of heat, is mounted on an aluminum heat sink weighing 0.31 kg and reaches a temperature of 100°C in ambient air at 20°C under steady- after the power is switched on?
Answer:
hello your question is incomplete attached below is the complete question
answer :
a) attached below
b) 63.71°c
Explanation:
A) Given data
The system has ; mass ( M ) , specific heat capacity , and surface area
attached below is a detailed solution
B) Given data
power generated = 60w
weight of heat sink = 0.31 kg
temperature given = 100°c
temp in ambient air = 20°c
lets take
specific heat capacity = 918.18 J /kg-k
density = 2702 kg/m^2
attached below is the detailed solution
Una barca intenta cruzar un río. La barca lleva una velocidad de 3 m/s con dirección perpendicular a la de la velocidad del agua que es de 4 m/s. Si el ancho del río es de 120 m. El tiempo en llegar a la otra orilla es de:
Answer:
El tiempo que tarda la barca en llegar a la orilla es 40 s.
Explanation:
Debido a que el río se mueve en dirección perpendicular a la barca, ésta se va a mover de manera diagonal, cuya velocidad ([tex]v_{b_{d}}[/tex]) viene dada por:
[tex]|v_{b_{d}}| = \sqrt{v_{r}^{2} + v_{b}^{2}} = \sqrt{(4)^{2} + (3)^{2}} = 5 m/s[/tex]
Por lo tanto, el módulo del vector velocidad diagonal es 5 m/s, y su dirección es:
[tex]tan(\alpha) = \frac{v_{r}}{v_{b}} = \frac{4}{3}[/tex]
Entonces, α es:
[tex] \alpha = arctan(\frac{4}{3}) = 53.13 ^{\circ} [/tex]
Ahora, debemos encontrar la distancia de la longitud diagonal que recorre la barca:
[tex] cos(\alpha) = \frac{a}{d_{d}} [/tex]
[tex] d_{d} = \frac{a}{cos(\alpha)} = \frac{120 m}{cos(53.13)} = 200.0 m [/tex]
Finalmente, el tiempo que le tomaría a la barca recorrer 200 m sería:
[tex]v_{b_{d}} = \frac{d_{d}}{t}[/tex]
[tex] t = \frac{200 m}{5 m/s} = 40 s [/tex]
Por lo tanto, el tiempo que tarda la barca en llegar a la orilla es 40 s.
Espero que te sea de utilidad!
A resistor and a capacitor are connected in series across a 150 Vac supply. When
the frequency is 40 Hz the current is 5 A, and when the frequency is 50 Hz the
current is 6 A. Find the resistance and capacitance for the of the resistor and
capacitor respectively.
Explanation:
for 40hz
since they are in series they will have the same amper
so R=30ohm
C=30F
for 50Hz
R=25
C=25
Reference sources reveal that a workpiece material has a unit horsepower of 1.6 hp/in3/min. For a turning operation, the cutting velocity is set at 500 ft/min with a corresponding feed of 0.025 in/rev. and a depth of cut of 0.2 in. From the given data, calculate:_______.
The question is incomplete. We have to calculate :
a). the cutting force
b). volumetric metal removal rate, MRR
c). the horsepower required at the cut
d). if the power efficiency of the machine tool is 90%, determine the motor horsepower
Solution :
Given :
Cutting velocity (v) = 500 ft/min
= 500 x 12 in/min
= 6000 in/min
Feed , f = 0.025 in/rev
Depth of cut, d = 0.2 in
b). Volumetric material removal rate, MRR = v.f.d
= 6000 x 0.025 x 0.2
= 30 [tex]$in^3 / min$[/tex]
c). Horsepower required = MRR x unit horsepower
= 30 x 1.6
= 48 hp
a). Cutting force,
[tex]$F=\frac{power}{cuting \ velocity}$[/tex]
[tex]$=\frac{48 \times 550}{500 /60}$[/tex] (1 hp = 550 ft lbf /sec)
= 3168 lbf
d). Machine HP required
[tex]$=\frac{HP}{\eta}$[/tex]
[tex]$=\frac{48}{0.9}$[/tex]
= 53.33 HP
Anything you want to do in Hootsuite can be found in the ________, with the main workspace in the _________?
Settings; Streams
Sidebar; center
Header; Sidebar
Nav-panel; dashboard
Answer:
Anything you want to do in Hootsuite can be found in the ___ Sidebar_____, with the main workspace in the ___center______
Sidebar; center
Explanation:
The main workspace of the Hootsuite is located in the center. The sidebar is where the core access to the Hootsuite functionality, like Streams, Inbox, Planner, Analytics, Publisher, and the App Directory, is obtained. Hootsuite is a media management platform for curating content, scheduling posts, managing team members, and measuring performances.
Waterjet cutting uses a _____. a) Very-small-diameter jet of water that exits the cutting nozzle at approximately the speed of sound. b) Diamond cutting wire cooled by a waterjet which also carries away the composite material as a slurry. c) Very-small-focused-stream of water that oscillates at 20,000 cycles per second.
Answer:
a
Explanation:
Waterjet cutting uses a very-small-diameter jet of water that exits the cutting nozzle at approximately the speed of sound. A water jet cutter, is oftentimes simply called a water jet is an industrial tool, like its name suggests, with the capabilities of cutting a different types of materials. Like its name suggests again, it uses water, although an extremely high-pressure jet of water to do the cutting. Other times, it uses a mixture of water and an abrasive substance to facilitate the cutting.
Air is saturated with water vapor at 35.0 oC and a total pressure of 1.50 atmospheres. If the molar flow rate of the dry air in this stream is 300 mols per minute, what is the molar flow rate of water vapor in the stream?
Answer:
11.541 mol/min
Explanation:
temperature = 35°C
Total pressure = 1.5 * 1.013 * 10^5 = 151.95 kPa
note : partial pressure of water in mixture = saturation pressure of water at T = 35°c )
from steam table it is = 5.6291 Kpa
calculate the mole fraction of H[tex]_{2}o[/tex] ( YH[tex]_{2}o[/tex] )
= 5.6291 / 151.95
= 0.03704
calculate the mole fraction of air ( Yair )
= 1 - mole fraction of water
= 1 - 0.03704 = 0.9629
Now to determine the molar flow rate of water vapor in the stream
lets assume N = Total molar flow rate
NH[tex]_{2}o[/tex] = molar flow rate of water
Nair = molar flow rate of air = 300 moles /min
note : Yair * n = Nair
therefore n = 300 / 0.9629 = 311.541 moles /min
Molar flowrate of water
= n - Nair
= 311.541 - 300 = 11.541 mol/min
When asked about favorite Thanksgiving leftovers, 9% of the people said turkey and 7100 said mashed potatoes. Which food is more popular? How do you know?
Answer:
how many people were asked though
Explanation:
