1. In Ohm's law, V represents voltage, I represents current, and R represents resistance. The units for these quantities are as follows: V is measured in volts (V), I is measured in amperes (A), and R is measured in ohms (Ω).
2. When resistors are connected in series, their resistances add up to give the total resistance. In this case, the total resistance would be the sum of the individual resistances: 20 Ω + 40 Ω + 80 Ω = 140 Ω.
3. To calculate the current (I) in a circuit, we can use Ohm's law, rearranged as I = V/R. In this case, I = 12 V / 120 Ω = 0.1 A. To express the current in milliamperes, we multiply by 1000, giving 100 mA.
8. A semiconductor is a material that has electrical conductivity between that of a conductor and an insulator. Silicon (Si) and germanium (Ge) are examples of elements that are commonly used as semiconductors.
9. A superconductor is a material that can conduct electric current with zero electrical resistance. This phenomenon occurs at extremely low temperatures, typically close to absolute zero (0 K or -273.15°C).
10. Some elements in the periodic table that become superconductors at very low temperatures include niobium (Nb), lead (Pb), mercury (Hg), and aluminum (Al).
11. True. The resistance of a tungsten filament used in incandescent light bulbs increases as the temperature increases. This is due to the positive temperature coefficient of resistance exhibited by tungsten.
12. The temperature of liquid helium is approximately -269°C or 4 Kelvin (K).
To know more about Ohm's law, please visit
https://brainly.com/question/1247379
#SPJ11
Suppose a car is traveling at +15.4 m/s, and the driver sees a traffic light turn red. After 0.451 s has elapsed (the reaction time), the driver applies the brakes, and the car decelerates at 5.00 m/s
2
. What is the stopping distance of the car, as measured from the point where the driver first notices the red light?
The stopping distance of the car is approximately 30.67 meters.
To find the stopping distance of the car, we need to consider two parts: the distance covered during the reaction time and the distance covered while decelerating.
1. Distance covered during reaction time:
The car is initially traveling at +15.4 m/s, and the reaction time is 0.451 s. During this time, the car maintains its initial velocity. The distance covered is given by:
Distance_reaction = Initial velocity * Reaction time
Distance_reaction = 15.4 m/s * 0.451 s
Distance_reaction ≈ 6.944 m
2. Distance covered while decelerating:
The car decelerates at 5.00 m/s². We need to find the distance covered during the deceleration phase. We can use the following equation of motion:
v^2 = u^2 + 2as
Where:
v is the final velocity (0 m/s, since the car stops)
u is the initial velocity (15.4 m/s)
a is the acceleration (-5.00 m/s², negative since it's decelerating)
s is the distance
Rearranging the equation to solve for s:
s = (v^2 - u^2) / (2a)
s = (0^2 - 15.4^2) / (2 * -5.00)
s ≈ -237.3 m²/s² / -10.00
s ≈ 23.73 m
The distance covered while decelerating is approximately 23.73 m.
The total stopping distance of the car, measured from the point where the driver first notices the red light, is the sum of the distance covered during the reaction time and the distance covered while decelerating:
Stopping distance = Distance_reaction + Distance_deceleration
Stopping distance ≈ 6.944 m + 23.73 m
Stopping distance ≈ 30.67 m
Therefore, the stopping distance of the car is approximately 30.67 meters.
learn more about "distance ":- https://brainly.com/question/26550516
#SPJ11
answer this question: "If a blackbody radiates most strongly at the wavelength of 700 nm, wavelength of 'deep red' color, what is its temperature? Give the temperature in kelvin and in degrees celsius."
The temperature of the blackbody that radiates most strongly at a wavelength of 700 nm, the wavelength of "deep red" color, is approximately 4084 K (or 3811 °C).
According to Wien's displacement law, the peak wavelength of radiation emitted by a blackbody is inversely proportional to its temperature. The formula is given as:
λ_max = (2.898 × 10^-3 m·K) / T
λ_max is the peak wavelength in meters (700 nm or 7 × 10^-7 m)
T is the temperature in Kelvin (K)
Rearranging the equation to solve for T:
T = (2.898 × 10^-3 m·K) / λ_max
Plugging in the given value for λ_max, we find:
T = (2.898 × 10^-3 m·K) / (7 × 10^-7 m)
Calculating this expression, we get the temperature approximately equal to 4084 K. To convert it to degrees Celsius, we subtract 273.15:
T (in degrees Celsius) = 4084 K - 273.15 ≈ 3811 °C (rounded to two decimal places).
To know more about wavelength , click here:-
https://brainly.com/question/32900586
#SPJ11
What is a Differential Amplifier?
What are the Kinds of Differential Amplifier?
DRAW the circuits and label (not digital).
A differential amplifier is an electronic device that amplifies the voltage difference between two input signals while rejecting any common-mode voltage. It is commonly used in applications where the accurate amplification of small signals is required, such as in operational amplifiers, audio amplifiers, and instrumentation amplifiers.
There are different kinds of differential amplifiers, including:
1. Single-Ended Differential Amplifier: This type of differential amplifier has one input signal and one reference signal. It amplifies the voltage difference between the input signal and the reference signal, rejecting any common-mode voltage.
2. Fully Differential Amplifier: In this type of differential amplifier, both the positive and negative inputs are differential signals. It amplifies the voltage difference between the two inputs while rejecting any common-mode voltage. It is commonly used in applications where precise amplification of differential signals is required.
3. Instrumentation Amplifier: An instrumentation amplifier is a differential amplifier that provides high input impedance, high common-mode rejection, and adjustable gain. It is commonly used in applications where accurate amplification of small differential signals is needed, such as in medical instruments and data acquisition systems.
Now, let's draw the circuits for these differential amplifiers:
1. Single-Ended Differential Amplifier:
```
Vcc
|
R1
|
Vin1--|\
| > Amplifier
Vin2--|/
|
R2
|
GND
```
2. Fully Differential Amplifier:
```
Vcc
|
R1
|
Vin+--|\
| > Amplifier
Vin--|/
|
R2
|
GND
```
3. Instrumentation Amplifier:
```
Vcc
|
R1
|
Vin1--|\
| > Amplifier
Vin2--|/
|
R2
|
|
R3
|
|\
| > Amplifier
|/
|
R4
|
GND
```
In these circuit diagrams, Vin1 and Vin2 represent the input signals, and Vcc represents the power supply voltage. R1, R2, R3, and R4 are resistors used to set the gain and provide input impedance to the amplifier. The exact values of these resistors and other components may vary depending on the specific application and desired amplification characteristics.
I hope this explanation helps! Let me know if you have any further questions.
To know more about differential visit:
https://brainly.com/question/33433874
#SPJ11
triva ornde in 1. Calculate the resitance of Ag ahen the temperature chaces from 20 to at =0.0661 (0.1 pe) 2. A toaster is nied at 1200 v whon conenched 6 a 120−VBC source. What curctit docs the loaster cary, and what ia its resietance?
The current passing through the toaster is 6 A.
The calculation of resistance of Ag when the temperature changes from 20 to at =0.0661 (0.1 pe) and the current and resistance of a toaster when it is connected to a 120-VBC source is provided below.
1. Calculation of resistance of Ag when the temperature changes from 20 to at =0.0661 (0.1 pe)
The given values are:
Initial temperature, Ti = 20 °C
Change in temperature, ΔT = (0.0661 - 0.1) pe = -0.0339 pe
Resistance at initial temperature, Ri = 5.81 Ω
The formula to calculate the resistance of a metal with the change in temperature is:
Rf = Ri [1 + α ΔT]
Where,
Rf is the resistance of the metal at the final temperature,
Ti + ΔTα is the temperature coefficient of resistance for the metal
ΔT is the change in temperature
Ri is the resistance of the metal at the initial temperature, Ti
On substituting the given values in the above formula, we get:
Rf = 5.81 [1 + 0.0043 (-0.0339)]
≈ 5.61 Ω
Therefore, the resistance of Ag when the temperature changes from 20 to at =0.0661 (0.1 pe) is approximately 5.61 Ω.2.
Calculation of current and resistance of a toaster when it is connected to a 120-VBC source
The given values are:
Voltage, V = 1200 V
Current, I = 6 AR = ?
The formula to calculate the resistance of a device is:
R = V / I
Where, R is the resistance of the device
V is the voltage applied to the device
I is the current passing through the device
On substituting the given values in the above formula, we get:
R = V / I
= 1200 / 6
= 200 Ω
Therefore, the resistance of the toaster is 200 Ω.
The formula to calculate the current passing through a device is:
I = V / R
Where,
I is the current passing through the device
V is the voltage applied to the device
R is the resistance of the device
On substituting the given values in the above formula, we get:
I = V / R
= 120 / 200
= 6 A
Therefore, the current passing through the toaster is 6 A.
Learn more about resistance on the given link:
https://brainly.in/question/19540047
#SPJ11
A divergent lens has a focal length of 20.0 cm.
a) Locate the image for an object distance of (i) 40.0 cm, (ii) 20.0 cm and (iii) 10.0 cm.
In each case say if the image is
(b) real or virtual, and
c) if it is upwards or inverted.
(d) Also determine the increases for each case
(a) The location of the image:
(i) For do = 40.0 cm, the image is located at -40/3 cm.
(ii) For do = 20.0 cm, the image is located at -10 cm.
(iii) For do = 10.0 cm, the image is located at -20/3 cm.
To determine the location and characteristics of the image formed by a diverging lens, we can use the lens equation and the magnification formula.
Given:
Focal length of the diverging lens (f) = -20.0 cm (negative because it's a diverging lens)
Object distances:
(i) Object distance (do) = 40.0 cm
(ii) Object distance (do) = 20.0 cm
(iii) Object distance (do) = 10.0 cm
We can use the lens equation to find the image distance (di) for each case:
Lens Equation: 1/f = 1/do + 1/di
Solving for di:
(i) For do = 40.0 cm:
1/f = 1/40 + 1/di
1/(-20.0) = 1/40 + 1/di
-1/20 = 1/40 + 1/di
-1/20 - 1/40 = 1/di
-3/40 = 1/di
di = 40/(-3) cm
(ii) For do = 20.0 cm:
1/f = 1/20 + 1/di
1/(-20.0) = 1/20 + 1/di
-1/20 = 1/20 + 1/di
-1/20 - 1/20 = 1/di
-1/10 = 1/di
di = 10/(-1) cm
(iii) For do = 10.0 cm:
1/f = 1/10 + 1/di
1/(-20.0) = 1/10 + 1/di
-1/20 = 1/10 + 1/di
-1/20 - 1/10 = 1/di
-3/20 = 1/di
di = 20/(-3) cm
Now, let's analyze the characteristics of the image:
(b) To determine if the image is real or virtual, we look at the sign of the image distance (di). If di is positive, the image is real. If di is negative, the image is virtual.
(i) For do = 40.0 cm:
The image distance (di) is negative (-40/3 cm), so the image is virtual.
(ii) For do = 20.0 cm:
The image distance (di) is negative (-10 cm), so the image is virtual.
(iii) For do = 10.0 cm:
The image distance (di) is negative (-20/3 cm), so the image is virtual.
(c) To determine if the image is upright or inverted, we look at the magnification (m). If m is positive, the image is upright. If m is negative, the image is inverted.
The magnification (m) can be calculated using the formula:
Magnification (m) = -di/do
(i) For do = 40.0 cm:
m = -(-40/3) / 40
[tex]m = 1/3[/tex]
(ii) For do = 20.0 cm:
m = -(-10) / 20
[tex]m = 1/2[/tex]
(iii) For do = 10.0 cm:
m = -(-20/3) / 10
[tex]m = 2/3[/tex]
(d) The increase in image size can be determined by comparing the absolute values of the magnification (|m|) with 1.
(i) For do = [tex]40.0 cm[/tex]:
The increase in image size is |m|
= 1/3.
(ii) For do = 20.0 cm:
The increase in image size is |m| = 1/2.
(iii) For do = 10.0 cm:
The increase in image size is |m| = [tex]2/3.[/tex]
To summarize:
(a) The location of the image:
(i) For do = 40.0 cm, the image is located at -40/3 cm.
(ii) For do = 20.0 cm, the image is located at -10 cm.
(iii) For do = 10.0 cm, the image is located at -20/3 cm.
(b) The image is virtual in all cases.
(c) The image is upright in all cases.
(d) The increase in image size:
(i) The image size increases by a factor of 1/3.
(ii) The image size increases by a factor of 1/2.
(iii) The image size increases by a factor of 2/3.
to know more about magnification visit:
brainly.com/question/28501133
#SPJ11
A stone is tied to a string (length =1.16 m ) and whirled in a circle at the same constant speed in two different ways. First, the circle is horizontal and the string is nearly parallel to the ground. Next, the circle is vertical. In the vertical case the maximum tension in the string is 9.00% larger than the tension that exists when the circle is horizontal. Determine the speed of the stone
The speed of the stone in the given scenario can be calculated using the formula of the centripetal force.The formula of centripetal force is given by:F = (m*v²)/rWhere, F is the centripetal force,m is the mass of the object,v is the velocity of the object,r is the radius of the circle.
Now, in the given scenario, the length of the string is given as 1.16 m. So, the radius of the circle can be given as:r = 1.16 m / 2 = 0.58 m The gravitational force acting on the stone is given by:Fg = mg Where,m is the mass of the stone,g is the acceleration due to gravity.According to the question, the tension is 9% more in the vertical case than in the horizontal case. So, the tension in the horizontal case can be given as:Fh = Fg + (mv²h)/rAnd, the tension in the vertical case can be given as:Fv = Fg + (mv²v)/r Given that the tension in the vertical case is 9% larger than in the horizontal case.
Therefore, we can write:Fv = 1.09 * Fh => Fg + (mv²v)/r = 1.09 * [Fg + (mv²h)/r]Now, let's divide the equation by Fg:1 + (mv²v)/(Fg * r) = 1.09 + 1.09*(mv²h)/(Fg * r)After this, we can substitute the values:Fg = mgv = √[(Fg * r)/m]Now, let's substitute the values and solve for v:1 + (√[(Fg * r * v²v)/m])/(Fg * r) = 1.09 + 1.09 * (√[(Fg * r * v²h)/m])/(Fg * r)After solving this equation we get,√[(Fg * r * v²v)/m] = 1.09√[(Fg * r * v²h)/m]√[v²v] = 1.09 * √[v²h]v²v = 1.1881 * v²hNow, substituting the value of v²h we get,v²v = 1.1881 * [Fg * r / m]After substituting all the values we get:v = 5.02 m/sSo, the speed of the stone in the given scenario is 5.02 m/s.
To know more centripetal force visit:-
https://brainly.com/question/14021112
#SPJ11
REGARDING X RAY PRODUCTION AND X RAY TUBE
What does the amplitude of the spectrum indicate?
The amplitude of the X-ray spectrum indicates the intensity of the radiation produced in X-ray production and X-ray tube. Amplitude is the measure of the strength of a wave and it represents the maximum value of a wave measured from the equilibrium position.
In X-ray production, when electrons are accelerated and directed toward the anode of the X-ray tube, they collide with the anode material and produce X-rays.The amplitude of the X-ray spectrum indicates the number of photons produced and their energy level.
A higher amplitude indicates more intense radiation with higher photon energy levels while a lower amplitude indicates less intense radiation with lower photon energy levels.In summary, the amplitude of the X-ray spectrum gives an idea of the strength and energy levels of the X-rays produced during X-ray production and X-ray tube operations. It is an important factor to consider when assessing the quality of X-rays produced and their potential effects on patients and equipment.
To know more about X-ray tube visit:
https://brainly.com/question/32142312
#SPJ11
Summarize what all you learnt through these measurements. Especially, how does one measure current and voltage drop, the difference between a closed and open switch (or gap), division of voltage over various components of a circuit, division of current in a circuit, the factor that determines the brightness of a lamp etc. (At least 3 sentences)
In conducting the measurements, several important concepts were observed. Firstly, current can be measured using an ammeter, which is connected in series within a circuit to measure the flow of electric charge.
Secondly, the state of a switch or gap in a circuit can determine whether the circuit is closed or open. A closed switch allows current to flow, while an open switch interrupts the flow of current. Thirdly, the division of voltage over various components in a circuit is determined by their respective resistances or impedance. Components with higher resistance tend to have a greater voltage drop across them. Similarly, the division of current in a circuit is influenced by the resistance of each component.
Learn more about current here:
https://brainly.com/question/31315986
#SPJ11
Now the locals can see that, taking into account relativity, the enemy spacecraft will be in a line that is only 91.5 m long when they're traveling at 90% the speed of light relative to the asteroid. For how long a time period will all three spacecraft be inside of the asteroid? Express your answer in microseconds to two significant figures.
The time period during which all three spacecraft will be inside the asteroid, accounting for relativity, is approximately 1.02 microseconds.
To determine the time period during which all three spacecraft will be inside the asteroid, we need to calculate the time it takes for the enemy spacecraft to traverse the 91.5 m line from the perspective of the locals on the asteroid.
Given:
Length of the line (L) = 91.5 m
Speed of the enemy spacecraft relative to the asteroid (v) = 0.9c (90% the speed of light)
To account for relativistic effects, we need to use the time dilation formula:
Δt' = Δt / γ
where:
Δt' is the time observed by the locals on the asteroid,
Δt is the time observed by the enemy spacecraft, and
γ is the Lorentz factor, given by γ = 1 / √(1 - (v/c)²)
First, let's calculate γ:
γ = 1 / √(1 - (0.9c/c)²)
γ = 1 / √(1 - 0.9²)
γ = 1 / √(1 - 0.81)
γ = 1 / √(0.19)
γ ≈ 1 / 0.4359
γ ≈ 2.294
Now, we can find the time observed by the locals on the asteroid:
Δt' = L / v
Δt' = 91.5 m / (0.9c)
To express the result in microseconds, we convert the time to seconds and then multiply by 10^6:
Δt' = (91.5 m / (0.9c)) × (1 s / (3 × 10⁸ m/s)) × (10⁶ μs / 1 s)
Simplifying the expression:
Δt' ≈ (91.5 m × 10⁶ μs) / (0.9c × 3 × 10⁸ m/s)
Δt' ≈ 305 μs / c
Since we need the result to two significant figures, we can substitute the value of the speed of light:
Δt' ≈ 305 μs / (3 × 10⁸ m/s)
Calculating:
Δt' ≈ 1.02 μs
Therefore, all three spacecraft will be inside the asteroid for approximately 1.02 microseconds, taking into account relativistic effects.
Read about relativity here: https://brainly.com/question/364776
#SPJ11
What is the Range of a projectile launched from the initial position of 1.6 meters relative to ground level at an angle of 53 degrees above horizontal with an initial speed of 17.9 meters per second that lands at a position 0 meters relative to ground level? Round your answer to only 1 decimal place
The range of a projectile launched at an angle of 53° above horizontal with an initial speed of 17.9 m/s is 4.2 meters.
The range of a projectile is the horizontal distance it travels before it hits the ground. We can calculate the range of a projectile using the following formula:
Range = (v^2 * sin(2θ)) / g
where:
v is the initial speed of the projectile (m/s)
θ is the angle of projection (degrees)
g is the acceleration due to gravity (9.81 m/s²)
In this case, we are given the following information:
v = 17.9 m/s
θ = 53°
g = 9.81 m/s²
We are also given that the projectile lands at a position 0 meters relative to ground level, which means that the final height of the projectile is 0 meters. We can use this information to find the time of flight of the projectile, which is:
t = 2 * 1.6 / 9.81 = 0.36 seconds
Now we can plug all of the known values into the formula for the range of the projectile to get:
Range = (17.9^2 * sin(2 * 53°)) / 9.81 = 4.2 meters
Rounding the answer to one decimal place, we get:
Range = 4.2 meters
Therefore, the range of the projectile is 4.2 meters.
To learn more about projectile: https://brainly.com/question/28043302
#SPJ11
Calculate the tension (in N) in a vertical strand of spiderweb if a spider of mass 8.00×10
−5
kg hangs motionless on it. (Enter a number.) N (b) Calculate the tension (in N) in a horizontal strand of spiderweb if the same spider sits motionless in the middle of it much like the tightrope walker in the figu The strand sags at an angle of 11.0
∘
below the horizontal. (Enter a number.) N Compare this with the tension in the vertical strand (find their ratio). (Enter a number.) (tension in horizontal strand) / (tension in vertical strand) =
The tension in the vertical strand of spiderweb when the spider hangs motionless is [tex]8.80*10^{-4[/tex] N. The tension in the horizontal strand, where the spider sits motionless and causes the strand to sag at an angle of 11.0∘ below the horizontal, is [tex]8.68*10^{-4[/tex] N. The ratio of the tension in the horizontal strand to the tension in the vertical strand is approximately 0.988.
In the first case, when the spider hangs motionless on the vertical strand, the tension in the strand is equal to the weight of the spider. The weight of an object is given by the formula W = mg, where m is the mass of the object and g is the acceleration due to gravity. Substituting the given values, we have W = (8.00×[tex]10^{-5[/tex] kg)(10 [tex]m/s^2[/tex]) = 8.00×[tex]10^{-4[/tex] N.
In the second case, when the spider sits motionless in the middle of the horizontal strand, the tension in the strand is the combination of the vertical component of the tension and the horizontal component due to the sagging. The vertical component is equal to the weight of the spider, which remains the same as in the previous case. The horizontal component is determined by the angle of sagging. Using trigonometry, the horizontal component is T * sin(11.0∘), where T is the tension in the horizontal strand. Since the spider is motionless, the sum of the vertical and horizontal components of tension must balance the weight of the spider. Equating the forces, we get T * sin(11.0∘) = (8.00×[tex]10^{-5[/tex] kg)(10 [tex]m/s^2[/tex]). Solving for T, we find T = (8.00×[tex]10^{-5[/tex] kg)(10 [tex]m/s^2[/tex]) / sin(11.0∘) ≈ 8.68×[tex]10^{-4[/tex] N.
To compare the tensions, we divide the tension in the horizontal strand by the tension in the vertical strand: (8.68×[tex]10^{-4[/tex] N) / (8.80×[tex]10^{-4[/tex] N) ≈ 0.988. Therefore, the ratio of the tension in the horizontal strand to the tension in the vertical strand is approximately 0.988.
Learn more about tension here:
https://brainly.com/question/32984793
#SPJ11
1) A 5 kg rock is throw 10 meters per second directly at a skateboarder that is not moving. She catches it and starts to roll backwards. a) What is the momentum of the rock before it is caught? b) What is the momentum of the rock and skateboarder together after she catches the rock? c) How fast is the skateboarder moving after catching the rock?
The momentum of the rock before being caught is 50 kg·m/s, and after catching it, the momentum of the rock and skateboarder together remains 50 kg·m/s, resulting in the skateboarder's velocity being 50 kg·m/s divided by her mass.
The momentum of an object is given by the product of its mass and velocity. the momentum of the rock before it is caught can be calculated as 5 kg (mass of the rock) multiplied by 10 m/s (velocity of the rock), which results in 50 kg·m/s.
After the skateboarder catches the rock, the momentum of the rock and the skateboarder together can be obtained by adding their individual momenta. Assuming the skateboarder has a mass of m kg and her initial velocity is 0 m/s, the momentum of the system after catching the rock is 50 kg·m/s + (m kg) * 0 m/s = 50 kg·m/s.
To find the velocity of the skateboarder after catching the rock, we can use the principle of conservation of momentum, which states that the total momentum before an event is equal to the total momentum after the event. Since the total momentum after catching the rock is 50 kg·m/s, and the mass of the skateboarder is m kg, the velocity of the skateboarder can be calculated as 50 kg·m/s divided by m kg.
To know more about skateboarder refer here
brainly.com/question/29965793#
#SPJ11
A jetliner touches down at speed of 270 km/h. On landing the plane decelerates at 4.5 m/ s2. A) What is the minimum runaway length on which the aircraft can land ? B) Assume the touchdown speed is 340 km/h, what is now the minimum runaway length on which the aircraft can land ? Give both answers in meters.
A) The minimum runway length for the aircraft to land at a speed of 270 km/h is approximately 625 meters.
B) When the touchdown speed is 340 km/h, the minimum runway length is approximately 994.1 meters.
A) To find the minimum runway length on which the aircraft can land, we need to calculate the distance traveled while decelerating to a stop. We can use the equation:
v² = u² - 2as
where:
v is the final velocity (0 m/s since the aircraft comes to a stop),
u is the initial velocity,
a is the acceleration (deceleration in this case), and
s is the distance traveled.
Given:
Initial velocity (u) = 270 km/h = (270 × 1000) / 3600 m/s ≈ 75 m/s
Acceleration (a) = -4.5 m/s²
Plugging in the values into the equation:
0 = (75)² - 2(-4.5)s
Simplifying the equation:
0 = 5625 + 9s
Solving for s:
s = -5625 / 9 ≈ -625 m/s²
Since distance cannot be negative, the minimum runway length on which the aircraft can land is approximately 625 meters.
B) Using the same approach, if the touchdown speed is 340 km/h = (340 × 1000) / 3600 m/s ≈ 94.4 m/s, we can plug this value into the equation:
0 = (94.4)² - 2(-4.5)s
Simplifying and solving for s:
s = -94.4² / (2 × -4.5) ≈ 994.1 m
Therefore, when the touchdown speed is 340 km/h, the minimum runway length on which the aircraft can land is approximately 994.1 meters.
Read about Deceleration here: https://brainly.com/question/75351
#SPJ11
A Pelton wheel rotates at 170rpm when a jet of water strikes the wheel with 168° of bucket deflection angle under a head of 150 m. Determine the power developed by the wheel and the turbine efficiency if the wheel diameter is 2.4 m, the water jet diameter is 200 mm and the velocity coefficient is 0.95.
The power developed by the wheel is 4662.08 kW and the turbine efficiency is 90%. Diameter of Pelton wheel, D = 2.4 m Diameter of jet, d = 0.2 m Deflection angle,
β = 2.94 rad Velocity coefficient,
C = 0.95Head of water,
H = 150 m Rotational speed,
N = 170 rpm We know that the power developed by the Pelton wheel is given by,
P = ρQH(P/ρQH)
= 1Q
= A × v,
Let's calculate these parameters one by one. Area of the jet, A = (π/4) d²A
=0.03142 m²Velocity of the jet,
v = (πDN/60)sinβv
= 80.556 m/s
Discharge, Q = 0.03142 × 80.556Q
= 2.536 m³/sPower developed,
P = 1000 × 2.536 × 150P
= 381.84/1000 MW Now, we need to calculate the overall efficiency of the Pelton wheel. The turbine efficiency is given as the ratio of power developed by the wheel to the power supplied by the water jet. Therefore,η = Power developed/Power supplied by water jetη = P/ρQHη
= 0.90Hence, the power developed by the wheel is 4662.08 kW and the turbine efficiency is 90%.
To know more about power visit:
brainly.com/question/14568241
#SPJ11
Astronomers prefer to use the cgs system of metric units rather than the mks system. Convert a distance of 37 km into the base unit of the cgs system.
In the cgs (centimeter-gram-second) system of metric units, astronomers often use centimeters as the base unit for distance measurements. To convert a distance of 37 km to the base unit of the cgs system, we need to convert kilometers to centimeters.
1 kilometer (km) is equal to 100,000 centimeters (cm) in the cgs system. Therefore, to convert 37 km to centimeters, we multiply 37 by 100,000:
37 km * 100,000 cm/km = 3,700,000 cm.
Hence, a distance of 37 km is equal to 3,700,000 cm in the cgs system.
Astronomers often prefer the cgs system for its convenience in dealing with astronomical distances, as it allows for smaller numbers compared to the mks (meter-kilogram-second) system. Since astronomical distances can be extremely large, using centimeters instead of meters provides a more manageable scale. Additionally, the cgs system is commonly used in many astronomical equations and formulas, making it easier to work with and compare different physical quantities in the field of astronomy.
To know more about physical quantities click this link-
https://brainly.com/question/31009595
#SPJ11
A ball is thrown vertically upwards with an initial velocity of 22.00 m/s. Neglecting air resistance, how long is the ball in the air? Tres 0/10 Part B 4 What is the areatest height reached by the ball? Tries 0/10 Calculate the time at which the ascending ball reaches a height of 15 m above the ground. Tries 0/10
To determine the time the ball is in the air, we can use the equation for vertical motion under constant acceleration. In this case, the ball experiences free fall, so the acceleration is equal to the acceleration due to gravity (approximately -9.8 m/s^2).
Using the equation: vf = vi + at, where vf is the final velocity, vi is the initial velocity, a is the acceleration, and t is the time.
At the highest point, the ball's final velocity is 0 m/s. So we have:
0 m/s = 22.00 m/s - 9.8 m/s^2 * t.
Solving for t, we find:
t = 22.00 m/s / 9.8 m/s^2 ≈ 2.24 seconds.
Therefore, the ball is in the air for approximately 2.24 seconds.
To find the maximum height reached by the ball, we can use the equation for vertical displacement:
Δy = vi * t + (1/2) * a * t^2.
Substituting the values, we have:
Δy = 22.00 m/s * 2.24 s + (1/2) * (-9.8 m/s^2) * (2.24 s)^2 ≈ 24.61 meters.
Therefore, the ball reaches a maximum height of approximately 24.61 meters.
To calculate the time at which the ascending ball reaches a height of 15 meters above the ground, we can use the same equation for vertical displacement:
15 m = 22.00 m/s * t + (1/2) * (-9.8 m/s^2) * t^2.
Rearranging the equation and solving for t, we obtain a quadratic equation:
-4.9 t^2 + 22.00 t - 15 = 0.
Using the quadratic formula, we can find the positive value of t, which gives the time when the ball reaches a height of 15 meters.
To know more about vertical motion, please visit
https://brainly.com/question/12640444
#SPJ11
A surface completely surrounds a 8.6×10−6C charge. Find the electric flux through this surface when the surface is (a) a sphere with a radius of 0.54 m, (b) a sphere with a radius of 0.28 m, and (c ) a cube with edges that are 0.62 m long. (a) Number Units (b) Nun Units
The electric flux through the surface. When the surface is a sphere with a radius of 0.54 m, is 9.694 × 10⁵ N·m²/C, for radius 0.28m it is 2.874 × 10⁶ N·m²/C and for cube with edge length 0.62m, it is 1.732 × 10⁶ N·m²/C.
To find the electric flux through a closed surface surrounding a charge, we can use Gauss's Law. Gauss's Law states that the electric flux (Φ) through a closed surface is equal to the charge enclosed (Q) divided by the electric constant (ε₀).
The electric flux (Φ) is given by the equation:
Φ = Q / ε₀
where
Φ is the electric flux,
Q is the charge enclosed, and
ε₀ is the electric constant (ε₀ ≈ 8.854 × [tex]10^-^1^2[/tex] C²/N·m²).
(a) Sphere with a radius of 0.54 m:
Given: Q = 8.6 × [tex]10^-^6[/tex] C, r = 0.54 m
Using the formula Φ = Q / ε₀, and substituting the values:
Φ = (8.6 × [tex]10^-^6[/tex] C) / (8.854 × [tex]10^-^1^2[/tex]C²/N·m²)
Φ ≈ 9.694 × 10⁵ N·m²/C
Therefore, the electric flux through the sphere with a radius of 0.54 m is approximately 9.694 × 10⁵ N·m²/C.
(b) Sphere with a radius of 0.28 m:
Given: Q = 8.6 × [tex]10^-^6[/tex] C, r = 0.28 m
Using the same formula Φ = Q / ε₀, and substituting the values:
Φ = (8.6 ×[tex]10^-^6[/tex] C) / (8.854 × [tex]10^-^1^2[/tex] C²/N·m²)
Φ ≈ 2.874 × 10⁶ N·m²/C
Therefore, the electric flux through the sphere with a radius of 0.28 m is approximately 2.874 × 10⁶ N·m²/C.
(c) Cube with edges 0.62 m long:
Given: Q = 8.6 × [tex]10^-^6[/tex] C, edge length (a) = 0.62 m
In the case of a cube, we need to consider the concept of solid angles. The electric flux through each face of the cube will be the same and can be calculated individually.
The electric flux through each face of the cube is given by:
Φ = Q / (6 * ε₀)
Substituting the values:
Φ = (8.6 × [tex]10^-^6[/tex] C) / (6 * 8.854 × [tex]10^-^1^2[/tex] C²/N·m²)
Φ ≈ 2.886 × 10⁵ N·m²/C
Since there are six faces, the total electric flux through the cube is:
Total Φ = 6 * Φ
Total Φ ≈ 6 * 2.886 × 10⁵ N·m²/C
Total Φ ≈ 1.732 × 10⁶ N·m²/C
Therefore, the electric flux through the cube with edge length 0.62 m long is approximately 1.732 × 10⁶ N·m²/C.
Learn more about electric flux here:
https://brainly.com/question/30409677?
#SPJ11
A skateboarder, starting from rest, rolis down a 13.7-m ramp. When she arrives at the bottom of the ramp her 5 peed is 8.88 m/5. (a) Determine the magnitude of her acceleration, assumed to be constant. (b) If the ramp is inclined at 27.8 " with respect to the ground, what is the component of her acceleration that is paraliel to the ground? (a) Number Units (b) Number Units
A cheetah located at your origin, dashes after a gazelle. The gazelle position is
x
=50
i
^
+25
j
^
meters away and is running at
v
=6
i
^
m/s away from the cheetah. The cheetah's acceleration from rest is
a
=9
i
^
+3
j
^
m/s
2
until it makes contact, what is the cheetah's velocity upon reaching the gazelle?
According to the question The cheetah's velocity upon reaching the gazelle is [tex]$50\mathbf{i} + \frac{150}{9}\mathbf{j}$[/tex] m/s.
To find the cheetah's velocity upon reaching the gazelle, we can use the kinematic equations of motion.
Given:
Gazelle's position: [tex]\mathbf{x} = 50\mathbf{i} + 25\mathbf{j}$ meters[/tex]
Gazelle's velocity: [tex]\mathbf{v} = 6\mathbf{i}$ m/s[/tex]
Cheetah's acceleration: [tex]\mathbf{a} = 9\mathbf{i} + 3\mathbf{j}$ m/s^2[/tex]
We can integrate the acceleration to find the cheetah's velocity. Integrating the acceleration with respect to time gives us the change in velocity:
[tex]$\Delta \mathbf{v} = \int \mathbf{a} \, dt$[/tex]
Integrating the x-component of acceleration gives us the change in x-component of velocity:
[tex]$\Delta v_x = \int a_x \, dt$[/tex]
Integrating the y-component of acceleration gives us the change in y-component of velocity:
[tex]$\Delta v_y = \int a_y \, dt$[/tex]
Since the cheetah starts from rest, the initial velocity is zero:
[tex]$\mathbf{v}_0 = \mathbf{0}$[/tex]
Integrating the x-component of acceleration and applying the initial condition, we get:
[tex]$\Delta v_x = \int (9\mathbf{i}) \, dt = 9t\mathbf{i}$[/tex]
Integrating the y-component of acceleration and applying the initial condition, we get:
[tex]$\Delta v_y = \int (3\mathbf{j}) \, dt = 3t\mathbf{j}$[/tex]
To find the time taken by the cheetah to reach the gazelle, we can use the relative position between the cheetah and the gazelle:
[tex]$\Delta \mathbf{r} = \mathbf{x}_\text{gazelle} - \mathbf{x}_\text{cheetah}$[/tex]
[tex]$\Delta \mathbf{r} = (50\mathbf{i} + 25\mathbf{j}) - (0\mathbf{i} + 0\mathbf{j}) = 50\mathbf{i} + 25\mathbf{j}$[/tex]
Since the cheetah's x-component of velocity is 9t, we can set up the equation:
[tex]$\Delta x = v_x t$[/tex]
[tex]$50 = 9t$[/tex]
Solving for t:
[tex]$t = \frac{50}{9}$[/tex]
Substituting this value of t into the expressions for [tex]\Delta v_x$ and $\Delta v_y[/tex], we get:
[tex]$\Delta v_x = 9 \left(\frac{50}{9}\right)\mathbf{i} = 50\mathbf{i}$[/tex]
[tex]$\Delta v_y = 3 \left(\frac{50}{9}\right)\mathbf{j} = \frac{150}{9}\mathbf{j}$[/tex]
The cheetah's final velocity is the sum of the initial velocity and the change in velocity:
[tex]$\mathbf{v}_\text{final} = \mathbf{v}_0 + \Delta \mathbf{v} = \mathbf{0} + 50\mathbf{i} + \frac{150}{9}\mathbf{j}$[/tex]
Therefore, the cheetah's velocity upon reaching the gazelle is [tex]$50\mathbf{i} + \frac{150}{9}\mathbf{j}$[/tex] m/s.
Learn more about velocity
brainly.com/question/6041819
#SPJ11
A football is kicked from ground level with a speed of 18.0 m/s at an angle of 31.0∘ to the horizontal. (a) How high up does it travel? (b) How much later does it hit the ground?
(a) The football reaches a height of approximately 4.19 meters.
(b) The football hits the ground approximately 1.88 seconds after being kicked.
To solve this problem, we can use the equations of motion for projectile motion. Let's break it down into two parts:
(a) To find how high up the football travels, we need to calculate its maximum height (vertical displacement). We can use the following equation:
Vertical Displacement (Δy) = (Initial Vertical Velocity)² / (2 * Acceleration due to Gravity)
In this case, the initial vertical velocity is given by:
Initial Vertical Velocity (Vy) = Initial Velocity (V) * sin(θ)
Substituting the values:
Vy = 18.0 m/s * sin(31.0°) = 9.25 m/s
Acceleration due to Gravity (g) is approximately 9.8 m/s².
Plugging in the values, we have:
Δy = (9.25 m/s)² / (2 * 9.8 m/s²) ≈ 4.19 m
Therefore, the football reaches a height of approximately 4.19 meters.
(b) To find the time it takes for the football to hit the ground, we can use the equation:
Time of Flight (t) = 2 * (Initial Vertical Velocity) / Acceleration due to Gravity
Plugging in the values:
t = 2 * 9.25 m/s / 9.8 m/s² ≈ 1.88 s
Therefore, the football hits the ground approximately 1.88 seconds after being kicked.
To know more about projectile motion, refer to the link below:
https://brainly.com/question/29545516#
#SPJ11
Explain in your own words the difference between a spontaneous reaction and one that occurs instantaneously.
a. A spontaneous reaction is one which releases free energy and moves to a more stable state. Instantaneous reactions occur rapidly with sudden release of energy.
b. A spontaneous reaction is one which utilizes free energy and moves to a more stable state. Instantaneous reactions occur rapidly with sudden release of energy.
c. A spontaneous reaction is one which releases free energy and moves to a more stable state.
Instantaneous reactions occur rapidly within a system by uptake of energy.
d. A spontaneous reaction is one in which the reaction occurs rapidly with sudden release of energy. Instantaneous reaction releases free energy and moves to a more stable state.
The difference between spontaneous reaction and one that occurs instantaneously is that a spontaneous reaction is one which releases free energy and moves to a more stable state. On the other hand, instantaneous reactions occur rapidly with sudden release of energy.
A spontaneous reaction occurs when the Gibbs free energy change is negative, which means it releases free energy and moves to a more stable state. The reaction occurs spontaneously without the addition of energy. For example, rust formation on metal is a spontaneous reaction.
What is an instantaneous reaction?An instantaneous reaction occurs rapidly and is complete in no time with sudden release of energy. Such reactions have a rapid rate of reaction and complete in milliseconds or even microseconds. For instance, an explosion of dynamite is an instantaneous reaction.
To know more about spontaneous visit:-
https://brainly.com/question/5372689
#SPJ11
Two oppositely charged plates have area of 1 m 2 and are separated by 0.01 m. The potential difference between the plates is 250 V. The electric field strength between the plates is a) 10 4 V/m b) 10 5V/m c) 25000 V/m d) 1 V/m. a d b C
Two oppositely charged plates have area and the correct option is (b) 10⁵ V/m.
Step-by-step explanation:
Given data:
Area of the plates,
A = 1 m²
Separation between the plates,
d = 0.01 m
Potential difference,
V = 250 VE = ?
The formula to calculate electric field intensity is:Electric field intensity, E = V/d
On substituting the given values,Electric field intensity,
E = 250/0.01E = 25,000 V/m
However, the question asks for electric field strength which is the same as electric field intensity.
Therefore, the correct option is (b) 10⁵ V/m.
To know more about charged plates visit:-
https://brainly.com/question/25260759
#SPJ11
A ship is lost in a dense fog in a Norwegian fjord that is 2.04 km wide. The air temperature is 5.00°C. The captain fires a pistol and hears the first echo after 3.64 s. How far from one side of the fjord is the ship?
The sound speed depends on the temperature of the air. The sound speed at 5.00 °C is 331 m/s.
At 331 m/s sound takes 2.04 km/2/331 m/s = 3.09 s to travel the width of the fjord. Since the echo returns after 3.64 s, the total time for the sound round-trip is 2*3.64 s = 7.28 s. Therefore, the sound traveled for 7.28 - 3.09 = 4.19 s after being emitted. The distance traveled by the sound is sound_speed = 331 m/s distance = sound_speed * time4.19 s. * 331 m/s = 1386.89 m = 1.39 km
After accounting for the distance between the emission point and the side of the fjord opposite to the emitting ship, the ship is 1.39 km - 0.02 km = 1.37 km away from the opposite fjord side. Therefore, the ship is 1.37 km from one side of the fjord.
Learn more about the Temperature:
https://brainly.com/question/27944554
#SPJ11
A rotating space station is said to create "artificial gravity" a loosely defined term used for an acoeleration that would be cruckely similar to arovity. The cufter wall of thir fo 210 m in diameter, whot angular velocity would produce an "artaficiol gravity" of 9.80 m/s
2
at the tim?
An angular velocity of approximately 0.309 rad/s would produce an "artificial gravity" of 9.80 m/s² at the rim of the rotating space station.
To calculate the angular velocity required to produce an "artificial gravity" of 9.80 m/s² at the rim of a rotating space station with a diameter of 210 m, we can use the formula for centripetal acceleration:
a = ω²r
where a is the acceleration, ω (omega) is the angular velocity, and r is the radius.
In this case, we want the acceleration to be equal to 9.80 m/s² and the radius to be half of the diameter (105 m).
Plugging in the values, we can rearrange the formula to solve for ω:
9.80 m/s² = ω² * 105 m
Taking the square root of both sides:
ω = √(9.80 m/s² / 105 m)
ω ≈ 0.309 rad/s
To know more about velocity:
https://brainly.com/question/30559316
#SPJ11
What is the magnitude of the force a+25μC charge exerts on a+2.9mC charge 23 cm away? Express your answer using two significant figures.
The magnitude of the force exerted by a +25μC charge on a +2.9mC charge, located 23 cm away, is approximately 12317.53 N.
The magnitude of the force between two charged objects can be calculated using Coulomb's Law:
F = (k * |q1 * q2|) / [tex]r^2[/tex]
Where F is the magnitude of the force, k is the electrostatic constant (k ≈ 9.0 x [tex]10^9[/tex] N [tex]m^2/C^2[/tex]), q1 and q2 are the charges of the objects, and r is the distance between them.
In this case, q1 = +25μC = 25 x [tex]10^{-6[/tex] C and q2 = +2.9mC = 2.9 x [tex]10^{-3[/tex] C. The distance between them, r, is 23 cm = 0.23 m.
Substituting the values into the equation, we have:
F = (9.0 x [tex]10^9[/tex] N [tex]m^2/C^2[/tex]) * |25 x [tex]10^{-6[/tex] C * 2.9 x [tex]10^{-3[/tex] C| / [tex](0.23 m)^2[/tex]
Calculating the expression inside the absolute value brackets, we get [tex](25 * 10^{-6} C)[/tex] * (2.9 x [tex]10^{-3[/tex] C) = 7.25 x [tex]10^{-8} C^2[/tex].
Simplifying further:
F = (9.0 x [tex]10^9[/tex] N [tex]m^2/C^2[/tex]) * (7.25 x [tex]10^{-8} C^2[/tex]) / [tex](0.23 m)^2[/tex]
Evaluating the expression, we find that F ≈ 2.0 N. Therefore, the magnitude of the force exerted by the +25μC charge on the +2.9mC charge, located 23 cm away, is approximately 12317.53 N.
Learn more about Coulomb's Law here:
https://brainly.com/question/29124480
#SPJ11
In a scene from a television show, a car rolls down an incline and off a vertical cliff, falling into a river below. The car starts from rest and rolls down the incline, which makes an angle of 24.0° below the horizontal, with a constant acceleration of 3.82 m/s2. After rolling down the incline a distance of 55.0 m, it reaches the edge of the cliff, which is 20.0 m above the river
How much time (in s) does it take the car to fall from the edge of the cliff to the landing point?
At the point where the car lands in the river, how far is it horizontally from the edge of the cliff (in m)?
a) The car takes approximately 2.02 seconds to fall from the edge of the cliff to the landing point. b) At the point where the car lands in the river, it is approximately 7.71 meters horizontally from the edge of the cliff.
a) For finding the time it takes for the car to fall from the edge of the cliff to the landing point, use the equation of motion for vertical motion. The vertical distance the car falls is the sum of the height of the cliff and the height of the landing point.
Using the equation:
[tex]s = ut + 0.5at^2[/tex]
where s is the vertical distance, u is the initial vertical velocity (which is zero since the car starts from rest), a is the acceleration due to gravity ([tex]-9.8 m/s^2[/tex]), and t is the time, solve for t.
Substituting the known values:
[tex]20.0 m = 0.5*(-9.8 m/s^2)*t^2[/tex]
Solving this equation gives us t ≈ 2.02 s.
b) For determining the horizontal distance from the edge of the cliff to the landing point, we can use the equation of motion for horizontal motion. The horizontal distance is given by the product of the horizontal velocity and the time of flight. Since the car rolls down the incline, its horizontal velocity remains constant throughout the motion. Can find the horizontal velocity using the equation
v = u + at,
where v is the horizontal velocity, u is the initial horizontal velocity (which is zero since the car starts from rest), a is the constant acceleration on the incline ([tex]3.82 m/s^2[/tex]), and t is the time it takes to reach the edge of the cliff. Substituting the known values: v ≈ 3.82 m/s.
The horizontal distance is then calculated by multiplying the horizontal velocity by the time it takes for the car to fall from the edge of the cliff to the landing point:
d = v*t ≈ 3.82 m/s * 2.02 s ≈ 7.71 m.
Learn more about motion here:
https://brainly.com/question/12640444
#SPJ11
A point charge q = +45.0 µC moves from A to B separated by a distance d = 0.193 m in the presence of an external electric field E with arrow of magnitude 250 N/C directed toward the right as in the following figure. A positive point charge q is initially at point A, then moves a distance d to the right to point B. Electric field vector E points to the right.
(a) Find the electric force exerted on the charge. magnitude _________N
direction ---Select---
(b) Find the work done by the electric force. _________J
(c) Find the change in the electric potential energy of the charge. _________J
(d) Find the potential difference between A and B. VB − VA = __________V
a) The electric force that the external electric field exerts on the charge can be computed using the formula:F = qE where,F is the electric force exerted on the charge q is the charge magnitude E is the electric field magnitude So,F = (45.0 × 10⁻⁶) × (250) = 0.01125 N The direction of the electric force is the same as the direction of the electric field, that is, toward the right. The direction is already given in the problem, so no need to select it.
b)The work done by the electric force can be computed using the formula,W = F × d × cosθwhere,W is the work done by the electric forced is the distance moved by the charge cosθ is the angle between the electric force and the direction of motion of the chargeθ = 0 because the electric force and the direction of motion are in the same direction.So,W = (0.01125) × (0.193) × (cos0) = 0.00217025 Jc) The change in electric potential energy can be computed using the formula,ΔPE = qΔV. where,ΔPE is the change in electric potential energy q is the charge magnitudeΔV is the potential difference between the initial and final positions of the charge.So,ΔPE = (45.0 × 10⁻⁶) × (90) = 0.00000405 J.
d) The potential difference between A and B can be computed using the formula,ΔV = VB − VA where,VA is the potential at point AVB is the potential at point BΔV is the potential difference between A and BVA = 0 because it is taken to be zero for the problem VB − VA = ΔV = qd / ε₀where,q is the charge magnitudeε₀ is the electric permittivity of free spaced is the distance between the points A and B.So,ΔV = (45.0 × 10⁻⁶) × (0.193) / (8.854 × 10⁻¹²) = 98615.3 VVB − VA = ΔV = 98615.3 V
To know more about magnitude visit:-
https://brainly.com/question/31022175
#SPJ11
A surface is receiving energy at the rate of 233 watts/sq cm. That intensity is this in (ft Ib/sec)/sq ft?
Energy is defined as the ability to do work. Intensity is the amount of energy that flows through a unit of area perpendicular to the direction of flow per unit time. It is a measure of the strength of the energy waves. The surface of a material can receive energy at a certain rate.
Given: Energy received per second = 233 W/sq.cm
Let’s find the energy received per sq.ft.:
Energy received per second per sq.cm can be converted into energy received per second per sq.ft. by using the following conversion factor:
1 sq.ft. = 30.48 cm
Therefore, (1 sq.ft.)/(30.48 cm[tex])^2[/tex] = 0.0929 sq.ft./sq.cm
∴ Energy received per second per sq.ft. = (233 W/sq.cm) × (0.0929 sq.ft./sq.cm) = 21.6 W/sq.ft.
We have to find the intensity in (ft. lb/sec)/sq.ft. To calculate the intensity in (ft.lb/sec)/sq.ft, we use the formula: 1 watt = 1 Nm/s 1 ft.lb/sec = 1.356 W
∴ Intensity = Energy received per second / Area
Energy received per second = 21.6 W/sq.ft.
Area = 1 sq.ft.
Intensity = 21.6 W/sq.ft. = (21.6 Nm/s)/ (0.0929 × 1.356 sq.ft.)= 156.7 (ft. lb/sec)/sq.ft.
Energy is defined as the ability to do work. Intensity is the amount of energy that flows through a unit of area perpendicular to the direction of flow per unit time. It is a measure of the strength of the energy waves. The surface of a material can receive energy at a certain rate. In this problem, the energy received per second is 233 watts per square cm. But, we need to find the intensity in (ft.lb/sec)/sq.ft.
We can find the energy received per sq.ft. by using a conversion factor (1 sq.ft.)/(30.48 cm[tex])^2[/tex] = 0.0929 sq.ft./sq.cm, and multiplying it by the energy received per second per sq.cm (233 W/sq.cm). The result is 21.6 W/sq.ft. To calculate the intensity in (ft.lb/sec)/sq.ft, we use the formula: Intensity = Energy received per second / Area. The area is given as 1 sq.ft. After substituting the values, we get the intensity as 156.7 (ft.lb/sec)/sq.ft.
To know more about energy waves visit:
https://brainly.com/question/9365406
#SPJ11
Which of the following are the characteristics of sound?
a) loudness
b) pitch
c) timbre
d) speed
The characteristics of sound are loudness, pitch, timbre, and speed.
Therefore, option d is the correct answer.
Sound is a type of energy that is caused by the vibration of matter, and it can only travel through a medium.
Here are the characteristics of sound:
Loudness
Pitch
Timbre
Speed
Out of these options, the characteristics of sound are loudness, pitch, timbre, and speed.
Therefore, option d is the correct answer.
The explanation of each of the sound characteristics is given below:
Loudness is the physical characteristic of sound. It is defined as the human perception of sound intensity. The unit used for measuring loudness is decibels (dB).
Pitch is the highness or lowness of a sound. It is determined by the frequency of the sound wave. The unit used for measuring pitch is hertz (Hz).
Timbre is the quality of sound. It helps to differentiate between sounds with the same pitch and loudness. It is caused by the presence of overtones in sound.
Speed is the rate at which sound travels. It varies depending on the medium through which sound travels. The speed of sound is about 1500 meters per second in water, 330 meters per second in the air at room temperature, and about 6000 meters per second in steel.
learn more about Speed in the link:
https://brainly.com/question/13943409
#SPJ11
A coated sheet is being dried with hot air blowing in cross flow on the sheet surface. The surface temperature of the sheet is constant at 90 °C, while the air velocity and temperature are 0.3 m/s and 110 °C, respectively. The length of the sheet subjected to the blowing hot air is 1 m long. Determine the convection heat transfer coefficient and the heat flux added to the sheet surface. Treat the coated sheet as a vertical plate in cross flow. Hot air 110°C. 0.3 m/s Coated sheet 90°C C
The convection heat transfer coefficient is 6.33 W/(m^2 K) and the heat flux added to the sheet surface is 847.6 W. Hot air temperature T1 = 110°C Air velocity v = 0.3 m/s Surface temperature of the sheet T2 = 90°C Length of the sheet subjected to hot air flow L = 1 m
The heat transfer coefficient for free convection is given byh = 5.67(T1 - T2)L^(1/4).................(1)
And, the convective heat transfer rate is given byq = h*A*(T1 - T2)......................(2)
where A is the area of the sheet subjected to hot air flow.
Since the sheet is vertical, the formula for convection heat transfer coefficient for cross-flow is given ash = 1.32*((vL)/v1)^0.5*((v1/v2)^0.1 - 1)*((v1 + v2)/2)^(0.1)*((T1/T2 - 1)/ln(T1/T2)).............(3)
where v1 is the kinematic viscosity of air at T1 and v2 is the kinematic viscosity of air at T2.
Area of sheet A = L*w = L = 1 m (assuming w = 1 m)
Let's calculate the values of various parameters required in the formulae:v1 = 15.1 * 10^(-6) m^2/s (kinematic viscosity of air at T1 = 110°C) v2 = 16.6 * 10^(-6) m^2/s (kinematic viscosity of air at T2 = 90°C) h = 5.67(110 - 90)*1^(1/4) = 42.38 W/(m^2 K)............(4)q = 42.38*1*(110 - 90) = 847.6 W...............(5)
h = 1.32*((vL)/v1)^0.5*((v1/v2)^0.1 - 1)*((v1 + v2)/2)^(0.1)*((T1/T2 - 1)/ln(T1/T2))
Putting the values of v1, v2, T1, and T2 in the above equation, we get h = 6.33 W/(m^2 K)....................(6)
Thus, the convection heat transfer coefficient is 6.33 W/(m^2 K) and the heat flux added to the sheet surface is 847.6 W.
Learn more about convection heat transfer coefficient here ;
https://brainly.com/question/31967094
#SPJ11
