i don't understand this, can someone help please?? ​

Answer:

Explanation:

The formula for determining the Emf induced in a loop is:

[tex]\varepsilon = \dfrac{d \phi}{dt}[/tex]

[tex]\varepsilon = \dfrac{d (B*A)}{dt}[/tex]

[tex]\varepsilon = A \times \dfrac{dB}{dt}[/tex]

[tex]\varepsilon = (side (l))^2 \times \dfrac{dB}{dt}[/tex]

where;

square area A = ( l²)

l² = 6.0 cm = 6.0 × 10⁻²

∴

[tex]\varepsilon = ( 6.0 \times 10^{-2})^2 \times 5.0 \times 10^{-3} \ T/S[/tex]

[tex]\varepsilon =18 \times 10^{6} \ V[/tex]

Recall that:

The resistivity of copper = [tex]1.68 \times 10^{-8}[/tex] ohm m

We can as well say that the length of the copper wire = perimeter of the square loop;

The perimeter of the square loop = 4L

Thus, the length of the copper wire  = 4 (6.0 × 10⁻² )m

= 24× 10⁻² m

Finally, the current in the loop is determined from the formula:

V = IR

where,

V = voltage

I = current and R = resistance of the wire

Making "I" the subject:

I = V/R

where;

[tex]R = \dfrac{\rho \times l}{A}[/tex]

[tex]R = \dfrac{\rho \times l}{\pi * r^2}[/tex]

[tex]R = \dfrac{1.68 *10^{-8} \times 24*10^{-2}}{\pi * (1*10^{-3})^2}[/tex]

[tex]R = 0.001283 \ ohms[/tex]

∴

[tex]I = \dfrac{18*10^{-6}}{0.001283}[/tex]

I = 14.029 mA

Answer:

375 is the answer.

Explanation:

Speed : Distance / Time taken

S: m/ s

s: 1500/4

375 m / s answer

Answer:

375m per minute

Explanation:

if you are looking for a diffrent unit just multiply your answer by however many minutes are in that time frame

Answer:

The launched angle θ = 30 degrees, the initial velocity Vo = 20 m/s, the initial horizontal velocity Vox= ?, the initial vertical velocity Voy = ?, the time of flight t = ? the maximum height h = ?

Vox = Vo * (cos of 30 degrees)

Voy = Vo * (sin of 30 degrees)

t = 2 * (Voy / g)

h = Voy * 0.5 t - 1/2 g * (0.5t)^2

I have given the equations for you to use, just plug – in the values and then solve in a step by step manner.

Answer:

approximately 15.68 meters.

Explanation:

Here is how;

First, let's calculate the time of flight for the t-shirt. We can use the vertical motion equation:

y = y0 + v0y * t - 0.5 * g * t^2

where:

y is the vertical displacement (27.7 m)

y0 is the initial vertical position (0 m)

v0y is the vertical component of the initial velocity (v0 * sin(theta))

g is the acceleration due to gravity (9.8 m/s^2)

t is the time of flight

Plugging in the values:

27.7 = 0 + (25.8 * sin(63.6°)) * t - 0.5 * 9.8 * t^2

Simplifying the equation, we get a quadratic equation:

4.9t^2 - (25.8 * sin(63.6°))t + 27.7 = 0

Solving this quadratic equation will give us the time of flight, t. Using the quadratic formula, we find that:

t ≈ 1.23 s

Now, let's find the horizontal displacement of the t-shirt using the horizontal motion equation:

x = x0 + v0x * t

where:

x is the horizontal displacement

x0 is the initial horizontal position (0 m)

v0x is the horizontal component of the initial velocity (v0 * cos(theta))

t is the time of flight

Plugging in the values:

x = 0 + (25.8 * cos(63.6°)) * 1.23

Calculating this:

x ≈ 14.92 m

The t-shirt falls short of reaching the person by the horizontal distance of:

Shortfall = 30.6 m - 14.92 m

Calculating this:

Shortfall ≈ 15.68 m

Therefore, the t-shirt will be approximately 15.68 meters short of reaching the person.

Answer:

Following are the response to the given question:

Explanation:

It's being used to measure the amount of light absorbed after traveling through a test tube (the amount of solar radiation received). For several quantitative estimations, this technique is widely employed. Spectrometer and Spectrometer were two devices that are used together to light intensity and light intensity.

It creates and diffuses phosphorescent light into the selected frequency, while the Spectrometer measures the strength of attenuation by the sample solution.

Diffraction beams or prisms are being used to convert polychromatic illumination into monochrome light.

Afterward, the sunlight has a certain hue. Once it reaches the specimen cuvette, it begins absorption. It falls on a sensor that transforms its intensity into such an electronic current.

Here are some ways to fill in such gaps:

In order to reach the specimen cuvette, the light from the light source must be routed via an aperture in order to be isolated by either a diffraction pattern. Light travels to the detector, which detects its intensity.

Question:- A scientist who studies the tiny microorganisms of the environment

Explanation:-

Microbiologist means a person who studies micro sized living organisms

Microbiologist word is combination of two words Micro and biologist

Answer:

microbiologist i think

hope it helps

please mark Brainliest if you think the answer is correct

Answer:

a) ε = 14.7 μv

b) ε = 21 μv

Explanation:

Given the data in the question;

Diameter of solenoid; d = 3 cm

radius will be half of diameter,  so, r = 3 cm / 2 = 1.5 cm = 1.5 × 10⁻² m

Number of turns; N = 40 turns per cm = 4000 per turns per meter

Current; [tex]I[/tex] = 0.235 A

change in time Δt = 0.40 sec

Now,

We determine the magnetic field inside the solenoid;

B = μ₀ × N × [tex]I[/tex]  

we substitute

B = ( 4π × 10⁻⁷ Tm/A ) × 4000 × 0.235  

B = 1.1881 × 10⁻³ T

Now, Initial flux through the coil is;

∅₁ = NBA = NBπr²  

and the final flux  

∅₂ = 0        

so, the εmf induced ε = -Δ∅/Δt = -( ∅₂ - ∅₁ ) / Δt

= -( 0 - NBπr² ) / Δt  

= NBπr² / Δt    

a)

for N = 7

ε = [ 7 × ( 1.1881 × 10⁻³ ) × π( 1.5 × 10⁻² )² ] / 0.40

ε = 14.7 × 10⁻⁶ v

ε = 14.7 μv      

b)

for N = 10

ε = [ 10 × ( 1.1881 × 10⁻³ ) × π( 1.5 × 10⁻² )² ] / 0.40

ε = 21 × 10⁻⁶ v

ε = 21 μv  

Answer:

asdasd dsa dasdasd sadas dasd asdasd asd asd dsa asdd 223 aasd ada dasd sa dasd dsaa sd adsd asasd

Explanation:

Answer:

a)  fem = - 2.1514 10⁻⁴ V,  b) I = - 64.0 10⁻³ A, c)    P = 1.38  10⁻⁶ W

Explanation:

This exercise is about Faraday's law

         fem = [tex]- \frac{ d \Phi_B}{dt}[/tex]

where the magnetic flux is

        Ф = B x A

the bold are vectors

        A = π r²

we assume that the angle between the magnetic field and the normal to the area is zero

         fem = - B π 2r dr/dt = - 2π B r v

linear and angular velocity are related

        v = w r

        w = 2π f

        v = 2π f r

we substitute

        fem = - 2π B r (2π f r)

        fem = -4π² B f r²

For the magnetic field of Jupiter we use the equatorial field B = 428 10⁻⁶T

we reduce the magnitudes to the SI system

       f = 2 rev / s (2π rad / 1 rev) = 4π Hz

we calculate

       fem = - 4π² 428 10⁻⁶ 4π 0.10²

       fem = - 16π³ 428 10⁻⁶ 0.010

       fem = - 2.1514 10⁻⁴ V

for the current let's use Ohm's law

        V = I R

        I = V / R

         I = -2.1514 10⁻⁴ / 0.00336

         I = - 64.0 10⁻³ A

Electric power is

        P = V I

        P = 2.1514 10⁻⁴ 64.0 10⁻³

        P = 1.38  10⁻⁶ W

Answer:

simple is rumple a daily ok I'll be

Answer:

Magnification = 1

Explanation:

given data

radius of curvature r = - 0.983 m

image distance u = - 0.155

solution

we get here first focal length that is

Focal length, f = R/2     ...................1

f = -0.4915 m

we use here formula that is

[tex]\frac{1}{v} + \frac{1}{u} + \frac{1}{f}[/tex]      .................2

put here value and we get

[tex]\frac{1}{v} = \frac{1}{0.155} - \frac{1}{4915}[/tex]  

so

Magnification will be here as

m = [tex]- \frac{v}{u}[/tex]

m =  [tex]\frac{0.155}{0.155}[/tex]

Answer:

The magnification is 1.5.

Explanation:

radius of curvature, R = - 0.983 m

distance of object, u = - 0.155 m

Let the distance of image is v.

focal length, f = R/2 = - 0.492 m

Use the mirror equation

[tex]\frac{1}{f}=\frac{1}{v}+\frac {1}{u}\\\\\frac{-1}{0.492}=\frac{1}{v}-\frac{1}{0.155}\\\\\frac{1}{v}=\frac{1}{0.155}-\frac{1}{0.492}\\\\\frac{1}{v}=\frac{0.492-0.155}{0.155\times 0.492}\\\\\frac{1}{v}=\frac{0.337}{0.07626}\\ \\v = 0.226 m[/tex]

The magnification is given by

m = - v/u

m = 0.226/0.155

m = 1.5

a) The mass flow rate through the nozzle is 0.27 kg/s.

b) The exit area of the nozzle is 23.6 cm².

a) The mass flow rate through the nozzle can be calculated with the following equation:

[tex] \dot{m_{i}} = \rho_{i} v_{i}A_{i} [/tex]

Where:

[tex]v_{i}[/tex]: is the initial velocity = 20 m/s

[tex]A_{i}[/tex]: is the inlet area of the nozzle = 60 cm²  

[tex]\rho_{i}[/tex]: is the density of entrance = 2.21 kg/m³

[tex] \dot{m} = \rho_{i} v_{i}A_{i} = 2.21 \frac{kg}{m^{3}}*20 \frac{m}{s}*60 cm^{2}*\frac{1 m^{2}}{(100 cm)^{2}} = 0.27 kg/s [/tex]  

Hence, the mass flow rate through the nozzle is 0.27 kg/s.

b) The exit area of the nozzle can be found with the Continuity equation:

[tex] \rho_{i} v_{i}A_{i} = \rho_{f} v_{f}A_{f} [/tex]

[tex] 0.27 kg/s = 0.762 kg/m^{3}*150 m/s*A_{f} [/tex]

[tex] A_{f} = \frac{0.27 kg/s}{0.762 kg/m^{3}*150 m/s} = 0.00236 m^{2}*\frac{(100 cm)^{2}}{1 m^{2}} = 23.6 cm^{2} [/tex]

Therefore, the exit area of the nozzle is 23.6 cm².

You can find another example of mass flow rate here: https://brainly.com/question/13346498?referrer=searchResults

I hope it helps you!                                                                   

a) Mass flow rate through the nozzle: 0.265 kilograms per second, b) Exit area of the nozzle: 23.202 square centimeters.

We determine the Mass Flow Rate through the nozzle and the Exit Area of the nozzle by means of the Principle of Mass Conservation. A nozzle is a device that works at Steady State, so that Mass Balance can be reduced into this form:

[tex]\dot m_{in} = \dot m_{out}[/tex] (1)

Where:

[tex]\dot m_{in}[/tex] - Inlet mass flow, in kilograms per second.

[tex]\dot m_{out}[/tex] - Outlet mass flow, in kilograms per second.

Given that air flows at constant rate, we expand (1) by dimensional analysis:

[tex]\rho_{in} \cdot A_{in}\cdot v_{in} = \rho_{out}\cdot A_{out}\cdot v_{out}[/tex] (2)

Where:

[tex]\rho_{in}, \rho_{out}[/tex] - Air density at inlet and outlet, in kilograms per cubic meter.

[tex]A_{in}, A_{out}[/tex] - Inlet and outlet area, in square meters.

[tex]v_{in}, v_{out}[/tex] - Inlet and outlet velocity, in meters per second.

a) If we know that [tex]\rho_{in} = 2.21\,\frac{kg}{m^{3}}[/tex], [tex]A_{in} = 60\times 10^{-4}\,m^{2}[/tex] and [tex]v_{in} = 20\,\frac{m}{s}[/tex], then the mass flow rate through the nozzle is:

[tex]\dot m = \rho_{in}\cdot A_{in}\cdot v_{in}[/tex]

[tex]\dot m = \left(2.21\,\frac{kg}{m^{3}} \right)\cdot (60\times 10^{-4}\,m^{2})\cdot \left(20\,\frac{m}{s} \right)[/tex]

[tex]\dot m = 0.265\,\frac{kg}{s}[/tex]

The mass flow rate through the nozzle is 0.265 kilograms per second.

b) If we know that [tex]\rho_{in} = 2.21\,\frac{kg}{m^{3}}[/tex], [tex]A_{in} = 60\times 10^{-4}\,m^{2}[/tex], [tex]v_{in} = 20\,\frac{m}{s}[/tex], [tex]\rho_{out} = 0.762\,\frac{kg}{m^{3}}[/tex] and [tex]v_{out} = 150\,\frac{m}{s}[/tex], then the exit area of the nozzle is:

[tex]\rho_{in} \cdot A_{in}\cdot v_{in} = \rho_{out}\cdot A_{out}\cdot v_{out}[/tex]

[tex]A_{out} = \frac{\rho_{in}\cdot A_{in}\cdot v_{in}}{\rho_{out}\cdot v_{out}}[/tex]

[tex]A_{out} = \frac{\left(2.21\,\frac{kg}{m^{3}} \right)\cdot (60\times 10^{-4}\,m^{2})\cdot \left(20\,\frac{m}{s} \right)}{\left(0.762\,\frac{kg}{m^{3}} \right)\cdot \left(150\,\frac{m}{s} \right)}[/tex]

[tex]A_{out} = 2.320\times 10^{-3}\,m^{2}[/tex]

[tex]A_{out} = 23.202\,cm^{2}[/tex]

The exit area of the nozzle is 23.202 square centimeters.

I assume the curve is flat and not banked. A car making a turn on the curve has 3 forces acting on it:

• its weight, mg, pulling it downward

• the normal force from contact with the road, n, pushing upward

• static friction, f = µn, directed toward the center of the curve (where µ is the coefficient of static friction)

By Newton's second law, the net forces on the car in either the vertical or horizontal directions are

∑ F (vertical) = n - mg = 0

∑ F (horizontal) = f = ma

where a is the car's centripetal acceleration, given by

a = v ²/r

and where v is the maximum speed you want to find and r = 25 m.

From the first equation, we have n = mg, and so f = µmg. Then in the second equation, we have

µmg = mv ²/r   ==>   v ² = µgr   ==>   v = √(µgr )

So the maximum speed at which the car can make the turn without sliding off the road is

v = √(0.80 (9.80 m/s²) (25 m)) = 14 m/s

Answer:

0.125

Explanation:

Density =mass/volume

Density =2.5/20

Density =0.125

Answer:

D=m/v

=2.5kg/(20/1000000)m^3

2.5kg÷0.000002m^3

1250000kgm^-3

Explanation:

20 is divided by 1000000 because m^3 is its si unit

Answer:

ΔU  = e(V₂ - V₁) and its value ΔU = -2.275 × 10⁻²¹ J

Explanation:

Since the electric potential at point 1 is V₁ = 33 V and the electric potential at point 2 is V₂ = 175 V, when the electron is accelerated from point 1 to point 2, there is a change in electric potential ΔV which is given by ΔV = V₂ - V₁.

Substituting the values of the variables into the equation, we have

ΔV = V₂ - V₁.

ΔV = 175 V - 33 V.

ΔV = 142 V

The change in electric potential energy ΔU = eΔV = e(V₂ - V₁) where e = electron charge = -1.602 × 10⁻¹⁹ C and ΔV = electric potential change from point 1 to point 2 = 142 V.

So, substituting the values of the variables into the equation, we have

ΔU = eΔV

ΔU = eΔV

ΔU = -1.602 × 10⁻¹⁹ C × 142 V

ΔU = -227.484 × 10⁻¹⁹ J

ΔU = -2.27484 × 10⁻²¹ J

ΔU ≅ -2.275 × 10⁻²¹ J

So, the required equation for the electric potential energy change is

ΔU  = e(V₂ - V₁) and its value ΔU = -2.275 × 10⁻²¹ J

Answer:

300J

Explanation:

Work done = Force x the distance travelled in the direction of the force

=300 x 1

=300J

Answer:

6.08

Explanation:

Given that,

Current, I = 0.8 A

Time, t = 76 h

We need to find the Ah rating of a battery. It can be calculated by taking the product of current and time. So,

Ah = (0.8)(76)

= 6.08 Ah

So, the Ah rating of the battery is 6.08.

Answer:

effect on motation.effect on direction

Answer:

Explanation:

The best way to do this is to remember the rule about the halfway mark in a parabolic path. At a trajectory's half way point in its travels, it will be at its max height. To get the total time in the air, we take that time at half way and double it. Here's what we know that we are told:

initial velocity is 20 m/s

Here's what we know that we are NOT told:

a = -9.8 m/s/s and

final velocity is 0 at an object's max height in parabolic motion.

We will use the equation:

[tex]v=v_0+at[/tex] where v is final velocity and v0 is initial velocity. Filling in:

0 = 20 + (-9.8)t and

-20 = -9.8t so

t = 2 seconds. The stone reaches its max height 2 seconds after it is thrown; that means that after another 2 seconds it will be on the ground. Total air time is 4 seconds.

Explanation:

Lasers produce a narrow beam of light in which all of the light waves have very similar wavelengths. The laser's light waves travel together with their peaks all lined up, or in phase. This is why laser beams are very narrow, very bright, and can be focused into a very tiny spot.

the question is about tyres of a race car, which are made of rubber and will be in contact with a race track, which is generally made from asphalt, the static coefficient of friction is in the range of (0.5–0.8), in dry conditions (Source: Friction and Friction Coefficients ).

Explanation:

please mark me as a brainlieast

Answer:

The correct solution is:

(a) 1.66

(b) 1.05

Explanation:

Given:

Bending stress,

[tex]\sigma_b = 25 \ kpsi[/tex]

Torsional stress,

[tex]\tau= 15 \ kpsi[/tex]

Yield stress of steel bar,

[tex]\delta_y = 60 \ kpsi[/tex]

As we know,

⇒ [tex]\sigma_{max}^' \ = \sqrt{\sigma_b^2 + 3 \gamma^2}[/tex]

        [tex]= \sqrt{(25)^2+3(15)^2}[/tex]

        [tex]=36.055 \ kpsi[/tex]

(a)

The factor of safety against static failure will be:

⇒ [tex]\eta_y = \frac{\delta_y}{\sigma_{max}^'}[/tex]

By putting the values, we get

        [tex]=\frac{60}{36.055}[/tex]

        [tex]=1.66[/tex]

(b)

According to the Goodman line failure,

[tex]\sigma_a = \sigma_b = 25 \ kpsi[/tex]

[tex]S_e = 40 \ kpsi[/tex]

[tex]\sigma_m = \sqrt{3} \tau[/tex]

     [tex]=\sqrt{3}\times 15[/tex]

     [tex]=26 \ kpsi[/tex]

[tex]Sut = 80 \ kpsi[/tex]

⇒ [tex]\frac{\sigma_a}{S_e} +\frac{\sigma_m}{Sut} =\frac{1}{\eta_y}[/tex]

      [tex]\frac{25}{40}+\frac{26}{80}=\frac{1}{\eta_y}[/tex]

              [tex]\eta_y = 1.05[/tex]

Answer:

The correct answer is "4.443 sec".

Explanation:

Given:

Mass of child,

= 34 kg

Mass of swing,

= 18 kg

Length,

= 4.9 m

The time period of pendulum will be:

T = [tex]2 \pi \sqrt{4g}[/tex]

  = [tex]2 \pi \sqrt{\frac{4.9}{9.8} }[/tex]

  = [tex]4.443 \ sec[/tex]  

Answer:

The time taken to back and forth is 4.4 s .

Explanation:

Length, L = 4.9 m

let the time period is T.

Acceleration due to gravity, g = 9.8 m/s^2

Use the formula of time period

[tex]T = 2 \pi\sqrt{L}{g}\\\\T = 2 \times 3.14\sqrt{4.9}{9.8}\\\\T = 4.4 s[/tex]

Answer:

15.88m/s

Explanation:

At the top of the roller coaster you will have three forces acting on the roller-coaster. See the image below. Fc is the centripetal force (for an object in circular motion), Fg is the gravitational force, and Fn is the normal force. To achieve the minimum speed we assume the roller-coaster is barely touching the vertical loop and so the normal force is zero. This leaves two acting forces.

[tex]F_g = F_c\\mg = \frac{m\times v^2}{r}\\v = \sqrt{gr} = \sqrt{9.81 \times 25.7} = 15.88 m/s[/tex]

Answer:

[tex]P_d=6203.223062W/mm^2[/tex]

Explanation:

From the question we are told that:

Voltage [tex]V=45kV[/tex]

Current [tex]I=50mAmp[/tex]

Diameter  [tex]d=0.50mm[/tex]

Heat transfer factor [tex]\mu= 0.87.[/tex]

Generally the equation for  Power developed is mathematically given by

[tex]P=VI\\\\P=45*10^3*50*10^{-3}[/tex]

[tex]P=2.250[/tex]

Therefore

Power in area

[tex]P_a=1400*0.87[/tex]

[tex]P_a=1218watt[/tex]

Power Density

[tex]P_d=\frac{P_a}{Area}[/tex]

[tex]P_d=\frac{1218}{\pi(0.5^2/4)}[/tex]

[tex]P_d=6203.223062W/mm^2[/tex]

Solution :

Let the positive [tex]x-axis[/tex] is along the East and the positive [tex]y[/tex] direction is along the north.

Given :

Mass of the Tesla car, [tex]m_1[/tex] = [tex]750 \ kg[/tex]

Mass of the Ford car, [tex]m_2 = 1250 \ kg[/tex]

Now let the initial velocity of Tesla car in the south direction be = [tex]-v_1j[/tex]

The initial momentum of Tesla car, [tex]p_1 = -750 \ v_1[/tex]

Let the initial velocity of Ford car in the east direction be = [tex]v_2 \ i[/tex]

So the initial momentum of the Ford car is [tex]p_2=1250\ v_2 \ i[/tex]

Therefore, the initial velocity of both the cars is [tex]p_i = p_1+p_2[/tex]

                                                                  [tex]=1250 \ v_2 \ i - 750\ v_1 \ j[/tex]

Now the final velocity of both the cars is [tex]v = 18 \ m/s[/tex]

So the vector form is :

[tex]v = 18\cos 32\ i-18 \sin 32 \ j[/tex]

  [tex]= 15.26 \ i - 9.54 \ j[/tex]

Therefore the momentum after the accident is

[tex]p_f=(m_1+m_2) \times v[/tex]

    [tex]=(750+1250) \times (15.26 \ i - 9.54 \ j)[/tex]

    [tex]= 30520\ i -19080\ j[/tex]

According to the law of conservation of momentum, we know

[tex]p_i = p_f[/tex]

[tex]1250 \ v_2 \ i - 750\ v_1 \ j[/tex]  [tex]= 30520\ i -19080\ j[/tex]

[tex]1250 \ v_2 = 30520[/tex]

[tex]v_2=24.4 \ m/s[/tex]

From, [tex]750\ v_1 = 19080[/tex]

We get, [tex]v_1=25.4 \ m/s[/tex]

Therefore the speed of Tesla car before collision = 25.4 m/s

The speed of ford car before collision = 24.4 m/s

Answer:

4

Explanation:

Answer:

In direct-current circuit theory, Norton's theorem is a simplification that can be applied to networks made of linear time-invariant resistances, voltage sources, and current sources. At a pair of terminals of the network, it can be replaced by a current source and a single resistor in parallel.

Answer:

The principle of a potentiometer is that the potential dropped across a segment of a wire of uniform cross-section carrying a constant current is directly proportional to its length. The potentiometer is a simple device used to measure the electrical potentials (or compare the e.m.f of a cell).

Explanation:

I hope it will help you

Answer:

Displacement

General Formulas and Concepts:

Kinematics

Explanation:

Displacement is the difference between the start position and end position.

Total Distance is the entire distance traveled between the start and end position.

Topic: AP Physics 1 Algebra-Based

Unit: Kinematics