Can ya pls answer dis rq!

Explanation:

it loses air pressure...

and low pressure can result in tire blowouts which can cause lost of control of your vehicle

Answer:

Explanation:

The series three. The series 3 will cut the voltage into 1/3. The current will also be lower because of the voltage drop.

The parallel circuit will not cut the voltage and the current will be tripled because each bulb is taking out exactly what it needs.

As an aside, house wiring would be a nightmare if the bulbs were connected in series. If one bulb burned out, you'd have to find it in the dark because they all would go out.

Answer: Cross-breeding method is commonly used for improving cattle breeds. Cross-breeding between two good varieties of cattle will produce a new improved variety. Cross breeding is defined as the process or the act of producing offspring particularly through mating two pure bred individuals but come from different breeds, varieties, or even species. Crossbreeding is undertaken to: Utilise the desired attributes of two or more breeds. Produce progeny better suited to target markets while maintaining environmental adaption. Improve productivity quicker in traits which are slow to change within a breed i.e. environmental adaption, fertility and carcass traits.

Hope it helps :)

Answer:

hlo

Explanation:

hlo olz mark me as brainlest

Explanation:

st system:the internationak system of measurement which i declared form internationäl convention of scientists held in france in 1960AD is Si system

CGS System:it measure in length in centimeter mass in gram time in second

Answer:

Decrease

Explanation:

The pressure is the force per unit area. So, P=F/A

Thus the pressure P is inversely proportional to contact area A.

So when area increases , the pressure will be decreasing.

Answer:

Explanation:

The sense of weightlessness in orbiting satellite is because of the lack of any contact-forces. ... Thus, both the astronaut and the satellite have the same value of g, which is again equal to the centripetal acceleration of the satellite. These two neutralize each other, causing everything to appear weightless.

MAKE ME BRAINLIEST

Our sun is 27 million times larger than our moon. Based on its mass, the sun's gravitational attraction to the Earth is more than 177 times greater than that of the moon to the Earth. If tidal forces were based solely on comparative masses, the sun should have a tide-generating force that is 27 million times greater than that of the moon. However, the sun is 390 times further from the Earth than is the moon. Thus, its tide-generating force is reduced by 3903, or about 59 million times less than the moon. Because of these conditions, the sun’s tide-generating force is about half that of the moon.

Answer:

Coording metal is a physical change.

Answer:

add text fully or atleast add book name edition . solution is in picture.  chk pictures ignore b part

Explanation:

Answer:

REENA IS STRONGER

Explanation:

so let's just find how long each person takes to carry the load half way, to proof who is stronger.

Rahul takes 5 minutes

5/2

= 2.5

so Rahul takes 2.5 minutes to travel 100 metres with 80 kg

where as

Reena take 4 minutes

4/2

= 2

so Reena takes 2 minutes to travel 100 metres with 80 kg

__________________________________________________

Therefore Reena is stronger because, she went 30 seconds before Rahul

Answer:

hope it helps you

Explanation:

fonot judge through bad handwriting :(

Answer:

15

Explanation:

muntiply the 5.0.3.0 ,you will get ans

[tex]\boxed{\sf E=QV^2}[/tex]

[tex]\\ \sf\longmapsto Q=\dfrac{E}{V^2}[/tex]

[tex]\\ \sf\longmapsto Q=\dfrac{3.92\times 10^{-4}}{24^2}[/tex]

[tex]\\ \sf\longmapsto Q=\dfrac{3.92\times 10^{-4}}{576}[/tex]

[tex]\\ \sf\longmapsto Q=0.006\times 10^{-4}C[/tex]

[tex]\\ \sf\longmapsto Q=6\times 10^{-1}C[/tex]

[tex]\\ \sf\longmapsto Q=0.6C[/tex]

Now

[tex]\boxed{\sf Q=CV}[/tex]

[tex]\\ \sf\longmapsto C=\dfrac{Q}{V}[/tex]

[tex]\\ \sf\longmapsto C=\dfrac{0.6}{24}[/tex]

[tex]\\ \sf\longmapsto C=0.025F[/tex]

Note:-

Explanation:

Because the temperature and the radiation are not correlated, they're not represented as functions of each other, they're represented as independent variables thus using graph 5 you cannot figure out how one affect another

Answer:

It doesn’t show how temperature and radiation relate to each other. It’s difficult to draw conclusions from data that’s separated this way.

If A = i - j + k, then the magnitude of A is

||A|| = √(1² + (-1)² + 1²) = √3

Then the unit vector in the direction of A is 1/||A|| multiplied by A :

u = A/||A|| = (i - j + k)/√3

(choice D)

Explanation:

Convert the time to seconds : 5minutes × 60 = 300seconds

Acceleration = Velocity / Time

Acceleration = 20m/s / 300s

Acceleration = 0.067m/s²

Distance = Velocity × Time

Distance = 20m/s × 300seconds

Distance = 6000m

Answer:

hey I am in class 6 why did you ask

The shape is connected in parallel so;

5.1) Ans;

[tex] \frac{1}{R} = \frac{1}{R1} + \frac{1}{R2} \\ \frac{1}{R} = \frac{1}{2} + \frac{1}{3} \\ \frac{1}{R} = \frac{3 + 2}{6} = \frac{5}{6} \\ R = \frac{6}{5} = 1.2 \: \: ohm[/tex]

5.2) Ans;

[tex] \frac{1}{R} = \frac{1}{R1} + \frac{1}{R2} \\ \frac{1}{R} = \frac{1}{8} + \frac{1}{10} \\ \frac{1}{R} = \frac{5 + 4}{40} = \frac{9}{40} \\ R = \frac{40}{9} = 4.4 \: \: ohm[/tex]

I hope I helped you^_^

Answer:

3 m/s

Explanation:

Given,

Total distance = 60 m

Total time = 20 s

We know that,

Average speed = Total distance/Total time

=> Average speed = 60 m/20 s

=> Average speed = 3 m/1 s

=> Average speed = 3 m/s

Average speed=Total distance/Total time

[tex]\\ \sf\longmapsto Average\:Speed=\dfrac{60}{20}[/tex]

[tex]\\ \sf\longmapsto Average\:Speed=3m/s[/tex]

Answer:

The MKS (metre, kilogram, second) system of units is the fundamental core of the SI (Systeme Internationale, or International System) of measurement. As various fields grow new forms of measurements based on MKS, terms or exact definitions may vary in different scientific or engineering disciplines. These inconsistencies are sorted out by the international committee that defines the SI system of units and keeps it up to date.

So the MKS is the static core, and the SI is the evolving, growing system of metric measurement.

Metres and kilograms were introduced after the French Revolution around 1790. Seconds were added by the 1830s, building the MKS system. More units came later. By 1948, a need was seen to develop a clear and consistent set of terms for measurement, and this led to 12 years of work, ending with the release of the first version of the SI in 1960.

The SI now has seven base units of measure. It begins with the original three metre, kilogram, and second, and adds the ampere for electricity, candela for light, kelvin for temperature, and mole for amount (number of atoms or molecules) of a substance.

The SI defines how each fundamental unit can be measured or obtained experimentally. These definitions have changed over time. For example, the metre was originally a measure related to the circumference of the Earth, then a set number of waves of a particular wavelength, and now a distance traveled by light in a vacuum in a certain period of time.

The SI also defines modifying terms such as milli-, centi-, and kilo- that are a specific number of each unit.

The SI includes many other derived units, as well.

By standardizing international use of measurements across different fields of science and engineering, the SI reduces confusion that would slow scientific progress and error that can produce engineering catastrophe such as the loss of the Mars Climate Orbiter in 1999 due to a table that should have been in metric units (kilograms and meters) being provided in United States customary units (pounds and inches).*

The Mars Climate Orbiter and its mission were lost due to a failure to use SI units consistently.

Hope this help you!:)

Answer:

Zero because the applied force is perpendicular to the motion of the object.

No work is done on an object moving is a circular path about a central attractive force.

Any work done in such a case would result in a change in the orbit.

The hydro power plant consists of a (artificial) dam that builds gravitational potential energy, P.E. from natural flowing water sources, by locating the dam along the water path. The stored potential energy, P. is converted into kinetic energy, K.E. as the water falls from the dam, down to the turbines, located at a much lower level according to the following principle of conservation of energy equation;

Total Mechanical Energy, M.E. = The potential energy of the water, P.E. + The kinetic energy of the water, K.E. = Constant

M.E. = P.E. + K.E. = Constant

Where;

P.E. = m·g·h

K.E. = (1/2)·m·v²

m = Mass

g = The acceleration due to gravity

h = The height of the dam

v = The velocity

The charts can be explained as follows;

Given that the potential energy P.E. = m·g·h, we have that the potential energy is directly proportional to the height of the dam, and therefore, at mid height, the potential energy would be half the maximum value, and we have;

At mid height, P.E. = (1/2)·[tex]\mathbf{P.E._{max}}[/tex]

At the top of the dam, the (vertical) velocity of the water = 0, therefore, the kinetic energy = 0

Therefore, at the top of the dam, we get;

M.E. = [tex]P.E._{max}[/tex] + 0 =

M.E. = [tex]\mathbf{P.E._{max}}[/tex]

Similarly, at the bottom of the dam, the height, h = 0, therefore, being proportional to the height, P.E. = 0, and the velocity is maximum, and at the bottom, we have;

M.E. = 0 + [tex]K.E._{max}[/tex]

The first chart, water is halfway down the dam

At the halfway down therefore, we have;

P.E. = (1/2)·[tex]\mathbf{P.E._{max}}[/tex]

M.E. = [tex]P.E._{max}[/tex] = (1/2)·

∴ K.E. = [tex]P.E._{max}[/tex] - (1/2)·

Therefore the first chart, water is halfway down the dam;

Halfway, K.E. = (1/2)·[tex]\mathbf{P.E._{max}}[/tex] = P.E.

∴ K.E. = P.E.  as shown on the chart

The second chart, water has reached the turbine

Water reaches the turbine at the bottom, and as explained above, we get;

M.E. = 0 + [tex]K.E._{max}[/tex]

∴ M.E.≈ [tex]K.E._{max}[/tex]

Therefore, when water has reached the turbine at the bottom of the dam, the kinetic energy is approximately proportional to the total mechanical energy as shown in the chart

The third chart, water is at the top of the dam

Here as shown above, we have;

The total mechanical energy, M.E. ≈ [tex]\mathbf{P.E._{max}}[/tex] as shown on the chart

Learn more about potential and kinetic energy here;

https://brainly.com/question/18683052

Answer:

Crumple zones are designed to absorb and redistribute the force of a collision. ... Also known as a crush zone, crumple zones are areas of a vehicle that are designed to deform and crumple in a collision. This absorbs some of the energy of the impact, preventing it from being transmitted to the occupants.

The reaction force must be:

75 N up

bending your arms

good luck bro

Answer:

không có điện

Explanation:

Answer:

At sea level

Explanation:

Because there is higher air pressure

Answer:D.Keeping track of the exact amount of wind on each plant

Answer:

The Greek philosophers leucippus and Democritus

Answer:

Democratus

Explanation:

I hope it help you