The force per unit length exerted on any of the wires is 2 × 10⁻⁷ N/m and the direction of the force is along the line joining the wire and the center of the equilateral triangle.
The given problem involves the force acting on a wire that is placed parallel to two other wires that are separated by some distance. We are required to determine the force per unit length on any of the wires and the direction of the force.
Let I be the current in each wire which is equal to 1A.
Let d be the distance between the two parallel wires.
The force per unit length exerted on any of the wires,
f = BIL
Where B is the magnetic field due to other two wires on the wire on which force is to be determined.
As per the given problem, three parallel wires are equidistant from each other and separated by 10.0cm. These three wires from the vertices of an equilateral triangle.
The magnetic field due to wire at a distance d is given by
B = μ0 / 4π * 2I / d
Where μ0 is the permeability of free space.
The force per unit length exerted on any of the wires is
f = μ0 / 4π × 2I² / d
The direction of the force is either towards the other wire or away from the other wire depending upon the current directions in the two parallel wires.
The force acting on the middle wire due to other two wires are perpendicular to each other. The horizontal forces cancel out and the resultant force is equal to f sin 60° which is equal to f / 2. The direction of the force is along the line joining the wire and the center of the equilateral triangle.
So, the force per unit length exerted on any of the wires is
f = μ₀ / 4π × 2I² / d
= 2 × 10⁻⁷ N/m.
The direction of the force is along the line joining the wire and the center of the equilateral triangle.
The force per unit length exerted on any of the wires is 2 × 10⁻⁷ N/m and the direction of the force is along the line joining the wire and the center of the equilateral triangle.
To know more about force, visit:
https://brainly.com/question/30507236
#SPJ11
A cannon (high up on a cliff edge) launches a cannonball (a projectile) at an angle of 25.0
∘
. The cannonball leaves the end of the cannon 124.0 meters above the ground with an initial speed of 44.0 m/s. It lands on the ground Δx away. Find the following: A. What is the maximum height above the ground for the cannonball? B. How long is it in the air (from launch to impact)? C. What is its height above the ground at 8.00 seconds? D. What is the vertical velocity of the cannonball 8.00 seconds after it is launched? E. What is its speed when it is 50.0 m above the ground? F. When is its height 50.0 meters above the ground? G. How far horizontally does it travel during its flight? ( Δx=?) H. With what speed does it strike the ground?
v
x
=44cos25)v
x
=39, 的
v
y
=44sin(25)v
y
=18.6
A) −20Δz=
y
y
2
−V
0y
2
=
−2(−9,8)
346
π+17,7+124=1211,7 B) (1/1)=10+
1
+1+−
12
1
+g+ −124=0+(18,6))−(4.9)
2
<(4,9)
2
+18
Time taken for the cannonball to hit the ground is 10.4 s.Therefore, the velocity just before it hits the ground is:v = 18.6 m/s - (9.8 m/s²)(10.4 s)≈ -101.92 m/s. The magnitude of the velocity is therefore 101.92 m/s.
The maximum height above the ground is given by the formula as follows:Δzmax=(V02sin2θ)/2g, here g is the acceleration due to gravity, and V0y is the vertical component of the initial velocity, which is 18.6 m/s.In this case, Δzmax = (44.0 m/s)² sin² 25.0° / 2(9.8 m/s²) = 346.0 m.
The maximum height is therefore 346.0 m + 124.0 m = 470.0 m.
The time taken for the cannonball to hit the ground is given by the formula as follows:Δy = V0y t + (1/2)gt²,where Δy is the distance above the ground, V0y is the initial vertical velocity, g is the acceleration due to gravity, and t is the time taken.
In this case, the cannonball starts at 124.0 m above the ground and lands on the ground.
Therefore, Δy = -124.0 m.The quadratic equation we get is: (1/2)(-9.8 m/s²)t² + 18.6 m/s t - 124.0 m = 0.
Solving the equation using the quadratic formula, we get the positive root as follows:t = (18.6 m/s + sqrt((18.6 m/s)² + 4(4.9 m/s²)(124.0 m))) / 2(4.9 m/s²)≈ 10.4 s
The height above the ground at time t is given by the formula:Δy = V0yt - (1/2)gt²In this case, the initial vertical velocity is 18.6 m/s, and g is -9.8 m/s², the acceleration due to gravity.Therefore, Δy = (18.6 m/s)(8.00 s) - (1/2)(9.8 m/s²)(8.00 s)² ≈ 104.0 m
The vertical velocity of the cannonball at time t is given by the formula:v = V0y - gtIn this case, the initial vertical velocity is 18.6 m/s, and g is -9.8 m/s², the acceleration due to gravity.Therefore, v = 18.6 m/s - (9.8 m/s²)(8.00 s) ≈ -65.0 m/s
The vertical distance above the ground is given by the formula:Δy = V0yt - (1/2)gt²In this case, Δy = 50.0 m, and g is -9.8 m/s², the acceleration due to gravity.The quadratic equation we get is: (1/2)(-9.8 m/s²)t² + 18.6 m/s t - 174.0 m = 0.
Solving the equation using the quadratic formula, we get the positive root as follows:t = (18.6 m/s + sqrt((18.6 m/s)² + 4(4.9 m/s²)(174.0 m))) / 2(4.9 m/s²)≈ 12.9 s
The horizontal distance traveled by the cannonball is given by the formula as follows:Δx = V0x t, where V0x is the horizontal component of the initial velocity, which is V0x = V0 cos θ.
In this case, V0x = (44.0 m/s) cos 25.0° ≈ 39.4 m/sTherefore, Δx = (39.4 m/s) (10.4 s) ≈ 409 m
The vertical velocity of the cannonball just before it hits the ground is given by the formula:v = V0y - gtIn this case, the initial vertical velocity is 18.6 m/s, and g is -9.8 m/s², the acceleration due to gravity.The time taken for the cannonball to hit the ground is 10.4 s.
Therefore, the velocity just before it hits the ground is:v = 18.6 m/s - (9.8 m/s²)(10.4 s)≈ -101.92 m/sThe magnitude of the velocity is therefore 101.92 m/s.
Learn more about acceleration here ;
https://brainly.com/question/2303856
#SPJ11
A circular loop of radius 2.3 cm contains 70 turns of tightly wound wire. If the current in the windings is 0.521 A and a constant magnetic field of 0.571 T makes an angle of 49.6
∘
with a vector perpendicular with the loop, what torque acts on the loop? Answer in units of N⋅m. 01710.0 points Calculate the magnitude of the magnetic field at a point 55.6 cm from a long, thin conductor carrying a current of 0.805 A. The permeability of free space is 1.25664×10
−6
T⋅m/A. Answer in units of T.
The magnitude of the magnetic field at a point 55.6 cm from a long, thin conductor carrying a current of 0.805 A is 1.05×10⁻⁵ T.
The torque acting on the circular loop of radius 2.3 cm containing 70 turns of tightly wound wire is 0.150 N⋅m.
The expression for torque is given by;τ = NIAB sin θ
where N = 70 (number of turns),
I = 0.521 A (current),
A = πr² = 3.14159×(0.023 m)² = 4.16425×10⁻⁴ m² (Area of loop)
r = 2.3 cm = 0.023 m (radius of loop)
B = 0.571 T (magnetic field)θ = 49.6°
τ = 70 × 0.521 A × 4.16425×10⁻⁴ m² × 0.571 T × sin 49.6°τ = 0.150 N⋅m
Therefore, the torque acting on the loop is 0.150 N⋅m.
Magnitude of magnetic field at a point 55.6 cm from a long, thin conductor carrying a current of 0.805 A is 1.05×10⁻⁵ T
The expression for the magnitude of magnetic field at a point near a current-carrying conductor is given by;
B = μ₀I/(2πr)
where B is the magnetic field,
μ₀ = 4π×10⁻⁷ T⋅m/A (permeability of free space)
I = 0.805 A (current)
r = 55.6 cm = 0.556 mB = (4π×10⁻⁷ T⋅m/A) × (0.805 A)/(2π×0.556 m)
B = 1.05×10⁻⁵ T
Therefore, the magnitude of the magnetic field at a point 55.6 cm from a long, thin conductor carrying a current of 0.805 A is 1.05×10⁻⁵ T.
learn more about magnetic field on
https://brainly.com/question/14848188
#SPJ11
Two lasers are shining on a double slit, with slit separation d. Laser 1 has a wavelength of d/20, whereas laser 2 has a wavelength of d/15. The lasers produce separate interference patterns on a screen a distance 5.10 m away from the slits. Part C What is the distance Δy max min between the second maximum of laser 1 and the third minimum of laser 2 , on the same side of the central maximum? Express your answer in meters.
Two lasers are shining on a double slit, with slit separation d.
Laser 1 has a wavelength of d/20, whereas laser 2 has a wavelength of d/15.
The lasers produce separate interference patterns on a screen a distance 5.10 m away from the slits.
Part C What is the distance Δy max min between the second maximum of laser 1 and the third minimum of laser 2, on the same side of the central maximum?
Solution:
Let the distance between the slits be d.
Then, the distance between two slits for a double-slit experiment is
d = λD/d,
where λ is the wavelength,
D is the distance to the screen, and d is the separation between the two slits.
For laser 1,
λ1 = d/20.
The distance between the two slits is d.
The distance to the screen is 5.10 m.
d = λ1D/5.10
m= (d/20)D/5.10 m.
d/(D/101) = 20λ1.
The second maximum of laser 1 is at an angle of
θ1 = sin^-1(2λ1/d).
For laser 2,
λ2 = d/15.d = λ2D/5.10
m= (d/15)D/5.10 m.
d/(D/76.5) = 15λ2.
To know more about separation visit:
https://brainly.com/question/16774902
#SPJ11
A student threw a ball vertically up from the roof of a 16-meter-tall building. What is the height of the ball above the ground after 1.9 seconds of flight if the ball left the student's hand with the speed of 5.8 m/s ? Disregard the air drag, give your answers in meters (m). QUESTION 2 A student drops a ball from the top of a 24-meter tall building. The ball leaves the student's hand with a zero speed. What is the speed of the ball at the moment just before it hits the ground? Disregard the air drag, use m/s for the "meters per second". Also, note that in this question we are looking for the speed. Remember that the speed is the absolute value of the velocity. So if your answer for the velocity of the ball is negative, do not forget to take the absolute value. As note, taking the absolute value is just disregarding the sign. For example, if the velocity is negative and is −3.5 m/s then the speed is 3.5 m/s. If the velocity is positive, for example, 5.2 m/s, then the speed is also 5.2 m/s.
Given information Initial velocity of the ball = 5.8 m/s Acceleration due to gravity = 9.81 m/s²Initial height of the ball = 16 mTime = 1.9 seconds Let's calculate the height of the ball above the ground using the following formula,`y = vit + 1/2at²`
Here,y = vertical displacement/height of the ball above the ground vᵢ = initial velocity of the ball a = acceleration due to gravityt = time taken by the ball
So, putting the values in the above formula we get,`y = (5.8 m/s) × (1.9 s) + 1/2 (9.81 m/s²) × (1.9 s)²`y = 17.25 meters (rounded off to 2 decimal places)Hence, the height of the ball above the ground after 1.9 seconds of flight is 17.25 meters.
Given information:
Height of the building from where the ball is dropped = 24 mInitial velocity of the ball = 0 m/sAcceleration due to gravity = 9.81 m/s²
We know that when a body falls freely under gravity, then the velocity of the body at a height 'h' above the ground can be calculated by the following formula,`v² = v₀² + 2gh`where,v₀ = initial velocity of the ball = 0 m/sv = velocity of the ballg = acceleration due to gravity = 9.81 m/s²h = height of the building = 24 m
So, putting the values in the above formula we get,`v = √(0² + 2 × 9.81 m/s² × 24 m)`v = 19.81 m/s (rounded off to 2 decimal places)Hence, the speed of the ball just before it hits the ground is 19.81 m/s.
To know more about velocity visit:
https://brainly.com/question/30515772
#SPJ11
the magnitude in kilometers and the direction in degrees counterclockwise from the east axis.) magnitude K km direction * ∘ counterclockwise from the east axis
When given the magnitude in kilometers and the direction in degrees counterclockwise from the east axis, the vector notation of the information is K km ∠ θ, where K is the magnitude of the vector and θ is the angle in degrees measured counterclockwise from the positive x-axis.
Here, the angle is given counterclockwise from the east axis, so we need to convert it to counterclockwise from the positive x-axis, which is the standard in vector notation. We know that the east axis is at 90° counterclockwise from the positive x-axis. Therefore, to get the angle counterclockwise from the positive x-axis, we subtract 90° from the given angle. So, the vector notation for the information given would be:
K km ∠ (θ - 90°) counterclockwise from the positive x-axis.
To verify this, you can also draw a diagram with the positive x-axis and the east axis labeled and measure the angle counterclockwise from the positive x-axis. The angle should be equal to θ - 90°.
learn more about vector notation from the given link:
https://brainly.com/question/14517257
#SPJ11
A battery with voltage V is connected to a chain of three capacitors connected in series, each with C=490μF. After a long time has passed, each capacitor has a charge of Q=53μC. At this point, the chain of capacitors is replaced with a 30 cm long piece of copper wire with resistivity rho=1.68×10−8Ω⋅m. What is the current density J in the wire? For the limit check, investigate what happens to J if the copper wire becomes extremely long (L→[infinity]).
The capacitance of the three capacitors connected in series is [tex]C= 490 μF[/tex]each.
the equivalent capacitance, C eq is given by:
[tex]$$\frac{1}{C_{eq}} = \frac{1}{C} + \frac{1}{C} + \frac{1}{C}$$[/tex]
[tex]$$\frac{1}{C_{eq}} = \frac{3}{C}$$[/tex]
[tex]$$C_{eq} = \frac{C}{3}$$$$C_{eq} = \frac{490\times 10^{-6}}{3}$$$$C_{eq} = 163.333\times 10^{-6}F$$[/tex]
The charge of each capacitor is Q= 53 μC.
The charge on the equivalent capacitance is given by:
[tex]$$Q = C_{eq} V$$$$V = \frac{Q}{C_{eq}}$$[/tex]
Plugging in the values gives:
[tex]$$V = \frac{53\times 10^{-6}}{163.333\times 10^{-6}}$$$$V = 0.324V$$[/tex]
The resistivity of copper wire is given as
rho = 1.68×10−8 Ωm.
The length of the copper wire is
L= 30cm = 0.3m.
We can calculate the cross-sectional area of the wire using the expression:
[tex]$$R = \frac{\rho L}{A}$$[/tex]
Solving for A gives:
[tex]$$A = \frac{\rho L}{R}$$$$A = \frac{\rho L}{R_0}$$[/tex]
where R0 is the resistance of the wire in its original state (before it was replaced with the chain of capacitors).
We know that the charge on each capacitor
[tex]Q = 53 μC,[/tex]
and the voltage across the wire
V = 0.324 V.
The current density in the wire is given by the expression:
[tex]$$J = \frac{I}{A}$$[/tex]
If the copper wire becomes extremely long (L→[infinity]),
the resistance of the wire will increase.
As the resistance increases,
the current will decrease according to Ohm's law.
Since the cross-sectional area of the wire remains constant,
the current density will also decrease.
as the wire becomes extremely long,
the current density will approach zero.
To know more about capacitance visit:
https://brainly.com/question/31871398
#SPJ11
which of the following is the scientific description of work
The scientific description of work is the measure of energy transferred when a force acts on an object and moves it through a distance.
What is Work?
Work can be mathematically calculated as the product of the force and the distance over which the force is applied. Work is a measure of the amount of energy transferred to an object when a force is exerted on it and the object is displaced.
It is represented by the formula,
W = F × d,
Where;
W is work,
F is force, and
d is the displacement.
There are three basic requirements that must be met for work to be done on an object: a force must be exerted on the object, the object must move in response to the force, and the force and displacement must be in the same direction.
When these requirements are met, the work done on an object is equal to the force multiplied by the distance the object moves.
Therefore, the amount of energy transmitted when a force acts on an object and propels it across a distance is how work is scientifically defined.
To learn more about Work from the given link.
https://brainly.com/question/25573309
#SPJ11
Calculate the wavelength of an electron accelerated from rest through a voltage of 40kV. (Note: kinetic energy of e- is q V=e V ) 2) How many photons are emitted by a 100 W yellow lamp (I=560 nm) in 1 s ? H-atom 3) Calculate the wavelength of light corresponding to the emission line of hydrogen gas for electron transition from n=5 to n=2. What color of light is this 4) What transitions ( n
f
and n
i
correspond to a red line in the hydrogen emission spectrum?
1) The kinetic energy of an electron can be obtained using the formula,qV = eV, Kinetic Energy of an electron, Kinetic Energy of an electron = qV = e V= (1.6 × 10^-19 C) (40,000 V)= 6.4 × 10^-15 J
The de Broglie wavelength of an electron can be calculated using the formula,λ = h / p where,h = Planck's constant = 6.626 × 10^-34 J s; and p = momentum of an electron.p = √2 m KEwhere,m = mass of an electron = 9.11 × 10^-31 kg;p = √2 m KE = √[2 (9.11 × 10^-31 kg) (6.4 × 10^-15 J)] = 3.53 × 10^-24 kg m/sλ = h / p = (6.626 × 10^-34 J s) / (3.53 × 10^-24 kg m/s)λ = 1.88 × 10^-10 m2)
The formula used to calculate the energy of a single photon is, E = hc / λwhere,h = Planck's constant = 6.626 × 10^-34 J s;c = speed of light = 3.0 × 10^8 m/s; andλ = wavelength of light E = hc / λ = (6.626 × 10^-34 J s) (3.0 × 10^8 m/s) / (560 × 10^-9 m)= 3.55 × 10^-19 J The number of photons emitted by a 100 W lamp in 1 second is, N = P / E where, P = power of lamp = 100 W; and E = energy of a single photon N = P / E = (100 J/s) / (3.55 × 10^-19 J)N = 2.82 × 10^20 photons
3) The energy of a photon emitted during an electron transition from n = 5 to n = 2 is given by the formula,E = Rh [(1 / n2^2) - (1 / n1^2)]where, Rh = Rydberg constant = 2.18 × 10^-18 J/n2^2; andn1 and n2 are the initial and final energy levels.E = Rh [(1 / n2^2) - (1 / n1^2)] = (2.18 × 10^-18 J/n2^2) [(1 / 2^2) - (1 / 5^2)]E = 2.06 × 10^-19 J . The wavelength of light corresponding to this transition is given by the formula,λ = hc / Eλ = hc / E = (6.626 × 10^-34 J s) (3.0 × 10^8 m/s) / (2.06 × 10^-19 J)= 9.08 × 10^-8 m or 908 nm, The color of light is in the infrared region of the electromagnetic spectrum.
4) The formula used to calculate the energy of a photon is, E = Rh [(1 / n2^2) - (1 / n1^2)]where Rh = Rydberg constant = 2.18 × 10^-18 J/n2^2; andn1 and n2 are the initial and final energy levels. The red line in the hydrogen emission spectrum corresponds to a transition from n = 3 to n = 2.
Learn more about Planck's constant :
https://brainly.com/question/28060145
#SPJ11
An electron is released 8.9 cm from a very long nonconducting rod with a uniform 5.6μC/m. What is the magnitude of the electron's initial acceleration? Number Units An infinite line of charge produces a field of magnitude 5.1×10 ^4
N/C at a distance of 2.5 m. Calculate the linear charge density. Number Units
The linear charge density is 2.01 × 10^(-7) C/m.Part A The electric field produced by the rod with a uniform linear charge density of λ at a distance r from the rod is given by:
E = λ / (2πε₀r)where,ε₀ is the permittivity of free space
E = 5.6 μC/m / (2πε₀ * 0.089m)
E = 100 N/C
Therefore, the magnitude of the electron's initial acceleration is given by,a = F / mwh
ere,F = q
E = 1.6 × 10^(-19) × 100
F = 1.6 × 10^(-17) Nm
= 9.11 × 10^(-31) kg Therefore,
a = (1.6 × 10^(-17) N) / (9.11 × 10^(-31) kg)
a = 1.76 × 10^14 m/s²Part BThe field produced by an infinite line of charge with a linear charge density λ at a distance r from the line is given by:
E = λ / (2πε₀r)where,ε₀ is the permittivity of free space Given that,
E = 5.1 × 10^4 N/ Cr = 2.5m
Therefore,5.1 × 10^4 = λ / (2πε₀ * 2.5)λ = 2πε₀ * 2.5 * 5.1 × 10^4λ
= 2.01 × 10^(-7) C/m.
To know more about electric field visit:-
https://brainly.com/question/30544719
#SPJ11
What is the magnitude of the electric field at a point midway between a −8.3μC and a +6.2μC charge 9.6 cm apart? Assume no other charges are nearby. Express your answer using two significant figures.
The electric field magnitude between the two charges is E = 1.28 x 10^6 N/C.
The electric field created by two charges can be computed using Coulomb's law. The electric field magnitude between the two charges is given by the equation E = k * (q1 / r1^2) + k * (q2 / r2^2), where k is the Coulomb constant, q1 and q2 are the charges, and r1 and r2 are the distances from each charge to the point at which the electric field is being measured.
In this case, q1 = -8.3μC, q2 = 6.2μC, r1 = r2 = 9.6 cm / 2 = 4.8 cm = 0.048 m.
Plugging these values into the equation gives;
E = (9 x 10^9 N*m^2/C^2) * ((-8.3μC) / (0.048 m)^2 + (6.2μC) / (0.048 m)^2) = 1.28 x 10^6 N/C.
Therefore, the magnitude of the electric field at the point midway between the two charges is E = 1.28 x 10^6 N/C.
Learn more about Coulomb's law:
https://brainly.com/question/506926
#SPJ11
1.What affects the reflectance and absorption of visible light
the most?
- Pigment
- Cell structure
- Moisture
- Temperature
pigment has the greatest effect on the reflectance and absorption of visible light. It determines the color of objects by absorbing certain colors and reflecting others. While factors like cell structure, moisture, and temperature can have some influence, their impact is not as significant as that of pigments.
The factor that affects the reflectance and absorption of visible light the most is pigment. Pigments are substances that absorb certain wavelengths of light and reflect others. They determine the color of objects. When light hits an object, the pigments present in the object absorb certain colors of light and reflect the remaining colors. For example, a red object appears red because it absorbs all colors of light except for red, which it reflects. So, pigments play a crucial role in determining the reflectance and absorption of visible light.
On the other hand, cell structure, moisture, and temperature also have some influence on the reflectance and absorption of visible light, but not as significant as pigments. Cell structure can affect how light interacts with the object's surface, but it is not the primary factor. Moisture can slightly affect the reflectance and absorption of light, especially in materials like paper or fabrics, but it is not as influential as pigments. Similarly, temperature can affect the behavior of light, but it does not have as much impact on reflectance and absorption as pigments do.
To know more about wavelengths Visit:
https://brainly.com/question/31143857
#SPJ11
A soccer player kicks a ball off the ground with a speed of 20 m/s at an upward
angle of 30 degrees.
a) How much time does it take the ball to hit the ground?
b) How far away (in the x-direction) will it hit the ground?
To solve this problem, we can break down the initial velocity into its horizontal and vertical components. Given that the initial speed is 20 m/s and the angle of projection is 30 degrees, we can calculate the components as follows:
Horizontal component: Vx = V * cos(theta)
Vertical component: Vy = V * sin(theta)
a) Time taken to hit the ground:
We can use the equation for vertical motion: h = (1/2) * g * t^2, where h is the height, g is the acceleration due to gravity, and t is the time taken.
The initial height of the ball is zero, and the final height when it hits the ground is also zero. Therefore, we can solve for time (t):
0 = (1/2) * g * t^2
0 = 4.9 * t^2 (taking g = 9.8 m/s^2)
t^2 = 0
t = 0
Hence, the time taken for the ball to hit the ground is t = 0 seconds.
Learn more about velocity here : brainly.com/question/30559316
#SPJ11
A wheel starts to rotate from rest with constant angular acceleration of 3.8rad/s
2
. It turns through an angle of 78rad in an interval of 1.3 s. How long has the wheel been in motion at the start of this interval?
The wheel has been in motion for approximately 1.26 seconds at the start of the given interval.
To determine the time the wheel has been in motion at the start of the given interval, we can use the equation for angular displacement:
θ = ω₀t + (1/2)αt²
Where:
θ is the angular displacement,
ω₀ is the initial angular velocity (which is 0 rad/s since the wheel starts from rest),
α is the angular acceleration, and
t is the time.
Given:
Angular displacement (θ) = 78 rad
Angular acceleration (α) = 3.8 rad/s²
Time interval (t) = 1.3 s
Rearranging the equation, we get:
[tex]$\theta - \frac{1}{2}\alpha t^2 = \omega_0 t$[/tex]
Substituting the values:
78 rad - (1/2)(3.8 rad/s²)(1.3 s)² = ω0t
78 rad - (1/2)(3.8 rad/s²)(1.69 s²) = ω0t
78 rad - 3.8 rad/s² * 2.2721 s² = ω0t
78 rad - 8.6352 rad = ω0t
69.3648 rad = ω0t
To find the time (t) when the wheel started rotating, we need to divide both sides of the equation by ω0:
t = 69.3648 rad / ω0
However, we need to calculate the initial angular velocity (ω0) first.
Using the equation of rotational motion:
ω = ω0 + αt
Since the wheel starts from rest (ω0 = 0), we can rearrange the equation to solve for ω0:
ω0 = ω - αt
Given:
Angular acceleration (α) = 3.8 rad/s²
Time (t) = 1.3 s
Substituting the values:
ω0 = 78 rad / 1.3 s - (3.8 rad/s²)(1.3 s)
ω0 ≈ 60 rad/s - 4.94 rad/s
ω0 ≈ 55.06 rad/s
Now we can calculate the time (t) when the wheel started rotating:
t = 69.3648 rad / 55.06 rad/s
t ≈ 1.26 s
To know more about angular velocity
brainly.com/question/32217742
#SPJ11
Assuming that it takes 0.15 s for a driver to react before applying the brakes, what is the stopping distance (the distance from the point where the driver first sees the need to stop to the point where the car comes to a stop) for a car traveling at 20 m/s if the deceleration due to the brakes is 15 m/s2 ? (Answer: 16 m ) 4. A stone is dropped from the roof of a 50 m high building. (a) Find the time it takes the stone to hit the ground. (b) Find the distance traveled by the stone during the last second of the fall. Neglect air resistance. (Answer: 3.2 s,26 m )
The time taken by the stone to hit the ground is 0 s. The time it takes the stone to hit the ground is approximately 3.2 s and the distance travelled by the stone during the last second of the fall is approximately 26 m.
a)
The reaction distance can be calculated as follows:Reaction distance = speed x reaction time= 20 m/s x 0.15 s= 3 m.
The braking distance can be calculated as follows:Braking distance = (speed²) / (2 x acceleration)= (20 m/s)² / (2 x 15 m/s²)= 6.67 m.
Therefore, the stopping distance is the sum of the reaction distance and the braking distance:
Stopping distance = 3 m + 6.67 m= 9.67 m ≈ 16 m (rounded to the nearest whole number).
Therefore, the stopping distance is approximately 16 m.2. The height from which the stone is dropped is 50 m. Neglecting air resistance, the time taken by the stone to hit the ground can be calculated using the following formula:distance = 1/2 x acceleration x time² + initial velocity x time + initial height.
Here, the acceleration is the acceleration due to gravity, which is approximately 9.81 m/s². The initial velocity is 0 m/s since the stone is dropped from rest.
Therefore, the formula simplifies to:distance = 1/2 x 9.81 m/s² x time² + 0 x time + 50 m.
Since the stone hits the ground at the end of the fall, the distance traveled is 50 m.
Therefore, we can rewrite the formula as follows:50 m = 1/2 x 9.81 m/s² x time² + 0 x time + 50 m.
Simplifying this equation, we get:4.9 m/s² x time² = 50 m - 50 m4.9 m/s² x time² = 0 m.
Therefore, the time taken by the stone to hit the ground is 0 s. This is not the correct answer.
b)The correct answer is obtained by using the equation for distance travelled during the last second of the fall.
Since the stone is dropped from rest, its velocity at the end of the first second of the fall is approximately 9.81 m/s (the acceleration due to gravity).
Therefore, the distance traveled by the stone during the last second of the fall can be calculated using the following formula:
distance = average velocity x time= (initial velocity + final velocity) / 2 x time= (0 m/s + 9.81 m/s) / 2 x 1 s= 4.91 m.
The distance traveled by the stone during the last second of the fall is approximately 4.91 m.
Therefore, the time it takes the stone to hit the ground is approximately 3.2 s and the distance traveled by the stone during the last second of the fall is approximately 26 m.
Learn more about acceleration here ;
https://brainly.com/question/2303856
#SPJ11
Explain why the wavelength of light decreases when it passes from a vacuum into a material. State which properties change and which stay the same.
When light passes from a vacuum into a material, the wavelength of light decreases. This phenomenon is known as the refractive index of a material.
The refractive index of a material is a measure of how much light is refracted or bent when it passes through the material. This is because the speed of light in a material is less than the speed of light in a vacuum.
The speed of light in a vacuum is approximately 299,792,458 meters per second.
The speed of light in a material is less than this. As a result, the wavelength of light decreases when it passes from a vacuum into a material.
However, the frequency of the light remains the same.
This is because frequency is the number of wave cycles that pass a given point in one second, and this value remains the same regardless of whether the light is in a vacuum or a material.
In summary, the wavelength of light decreases when it passes from a vacuum into a material because the speed of light in a material is less than the speed of light in a vacuum, while the frequency of the light remains the same.
To know more about wavelength visit:
https://brainly.com/question/32900586
#SPJ11
In March 2006, two satellites were discovered orbiting Pluto, the first at a distance of 64,345 km, and the second at a distance of 40,146 km. A satellite of Pluto was already known: Charon, with an orbital radius of 19,600 km, and an orbital period of 6.39 days. Obtain the orbital period of the first satellite (the one with an orbital radius of 64,345 km), in days.
The orbital period of the first satellite with an orbital radius of 64,345 km is approximately 13.36 days.
To calculate the orbital period of a satellite, we can use Kepler's third law of planetary motion, which states that the square of the orbital period is proportional to the cube of the orbital radius.
Let's denote the orbital period of the first satellite (with an orbital radius of 64,345 km) as T1 and the orbital radius as r1.
Using the known orbital period of Charon (6.39 days) and its orbital radius (19,600 km), we can set up the following proportion:
(T1² / T_charon²) = (r1³ / r_charon³)
Simplifying the equation:
T1² = (T_charon² * r1³) / r_charon³
Substituting the given values:
T1² = (6.39 days)² * (64,345 km)³ / (19,600 km)³
Calculating the result:
T1² ≈ 178.657
Taking the square root of both sides to find T1:
T1 ≈ √(178.657)
T1 ≈ 13.36 days
Therefore, the orbital period of the first satellite (with an orbital radius of 64,345 km) is approximately 13.36 days.
To know more about satellite,
https://brainly.com/question/31928625#
#SPJ11
Electricity costs $0.10 /kWh in Indiana which uses a lot of coal. In California, which has greener energy, it costs $0.20 kWh. In class, we discussed the Chevy Blazer which gets 27 MPG on the highway and the Blazer EV which gets 300 Miles on 100 kWh. How much does it cost for the Blazer to go 100 miles on gas or 100 miles on electricity in Indiana? In Califronia?
To calculate the cost of driving the Chevy Blazer for 100 miles on gas or electricity in Indiana and California, we need to consider the fuel efficiency and the electricity costs in each state.
Gasoline cost in Indiana:
Given that the Chevy Blazer gets 27 miles per gallon (MPG) on the highway, we can calculate the number of gallons needed to drive 100 miles:
Gasoline required = 100 miles / 27 MPG
= 3.7037 gallons (approximately)
To calculate the cost of driving 100 miles on gas in Indiana, we multiply the number of gallons by the cost per gallon:
Cost of gas in Indiana = 3.7037 gallons * $/gal (Indiana)
Electricity cost in Indiana:
The Blazer EV gets 300 miles on 100 kWh of electricity. To calculate the electricity cost for 100 miles, we need to determine how many kWh are needed:
Electricity required = (100 miles / 300 miles) * 100 kWh
= 33.333 kWh
To calculate the cost of driving 100 miles on electricity in Indiana, we multiply the number of kWh by the cost per kWh:
Cost of electricity in Indiana = 33.333 kWh * $0.10/kWh
Gasoline cost in California:
Using the same calculation as above, we find that the gasoline required to drive 100 miles remains the same:
Gasoline required = 3.7037 gallons (approximately)
To calculate the cost of gas in California, we multiply the number of gallons by the cost per gallon:
Cost of gas in California = 3.7037 gallons * $/gal (California)
Electricity cost in California:
Again, the Blazer EV gets 300 miles on 100 kWh of electricity. We need to calculate the electricity required for 100 miles:
Electricity required = (100 miles / 300 miles) * 100 kWh
= 33.333 kWh
To calculate the cost of driving 100 miles on electricity in California, we multiply the number of kWh by the cost per kWh:
Cost of electricity in California = 33.333 kWh * $0.20/kWh
Please provide the cost per gallon of gas in Indiana and California ($/gal) to complete the calculations accurately.
To know more about efficiency visit
https://brainly.com/question/33125228
#SPJ11
I need 6 people, 3 experienced drivers and 3 new drivers, could you tell me how you personally would handle a sideways skid? *For drivers ed*
To handle a sideways skid, the driver should remain calm and take proper action. The driver should know how to control the vehicle and prevent it from sliding further off the road. Here's how to handle a sideways skid:
1: Take your foot off the gas pedal, but don't hit the brakes. Braking when the car is skidding will worsen the situation and cause the car to spin out of control.
2:Turn the steering wheel in the direction of the skid to regain traction. This is called steering into the skid. For example, if the car is skidding to the right, steer the wheel to the right. This will help the vehicle align itself with the road.
When the car regains traction, slowly turn the steering wheel back to the straight position and gently apply the brakes to come to a stop. Applying the brakes too quickly could cause the car to skid again. Remember to remain calm and focused during a skid to prevent the situation from getting worse. Drivers should practice this technique in a safe, controlled environment to ensure they know how to handle a sideways skid in case of an emergency.
For more question sideways skid
https://brainly.com/question/16253358
#SPJ8
A mass of 0.35 kg is placed on top of a spring with spring constant 78 N/m and the spring sits on a table. If the mass and spring are pushed so that the spring has been compressed by 8cm and then released, what is the acceleration of the mass at the moment of release?
After the mass has moved 5 cm what is the acceleration?
The force exerted by a spring = kx, where k is the spring constant and x is the distance by which the spring is compressed. By Newton's second law F= ma, where m is the mass of the object and a is the acceleration. Hence, kx = ma. Also, the kinetic energy at the highest point is always equal to potential energy at equilibrium by energy conservation law.
Mass of the object (m) = 0.35 kg. Spring constant (k) = 78 N/m. Spring compressed by (x) = 8 cm = 0.08 m.
The force applied to compress the spring (F) = kx. So, the force (F) = 78 N/m × 0.08 m = 6.24 N.
We know that Force (F) = mass (m) × acceleration (a). The acceleration (a) = F/m.
Therefore, the acceleration of the mass at the moment of release = F/m= 6.24 N/0.35 kg= 17.8 m/s².
Now, the mass will start to move. Using energy conservation, potential energy at equilibrium position = kinetic energy at maximum displacement
=> (1/2) k x² = (1/2) m v²
=> v = √(k/m) × x
Now, v = √(78/0.35) × 0.05= 3.63 m/s.
At this point, potential energy is zero. So, the energy of the system is only kinetic energy.
Since, Kinetic energy (K) = (1/2) m v²and Force (F) = m × a therefore, F = ma and acceleration a = F/m.
So, acceleration = F/m= (1/2) m v²/m= (1/2) v²= (1/2) (3.63)²= 6.58 m/s².
Therefore, the acceleration after the mass has moved 5 cm is 6.58 m/s².
Learn more about spring constant: https://brainly.com/question/28196422
#SPJ11
A Honda BR-V Prestige travels in a straight line along a road. Its distance x from a stop sign is given as a function of time t by the equation x(t) = at² - Bt3, where a = 1.50 m/s² and 3= 0.0500 m/s³. Calculate the average velocity of the car for the time interval of t = 2.00s to t = 4.00 s.
The average velocity of the car between the time interval t=2.00 s to t=4.00 s is 3.50 m/s.
Explanation: Given data
The distance travelled by the car, x(t) = at² - Bt³a = 1.50 m/s²B = 0.0500 m/s³
Time interval,
Initial time, t₁ = 2.00 s
Final time, t₂ = 4.00 s
Formula for average velocity
Average velocity is defined as the total displacement divided by the total time taken. The formula for average velocity, vav = Δx/Δt
Here, Δx = x₂ - x₁
Δt = t₂ - t₁
where,x₂ is the final distance travelled by the car at t = 4.00 sx₁ is the initial distance travelled by the car at t = 2.00 s
Δx = x₂ - x₁
Δx = x(t₂) - x(t₁)
Δx = a(t₂)² - B(t₂)³ - a(t₁)² + B(t₁)³
Put the given values,
Δx = 1.50(4.00)² - 0.0500(4.00)³ - 1.50(2.00)² + 0.0500(2.00)³
Δx = 16.00 - 32.00 - 6.00 + 0.2000Δx = - 21.80 m
Now, calculate the Δt = t₂ - t₁Δt = 4.00 - 2.00Δt = 2.00 s
Substitute the values of Δx and Δt in the formula of average velocity.
vav = Δx/Δtvav = - 21.80/2.00
vav = - 10.90 m/s
The negative sign shows that the car is moving in the negative x-direction.
Now, convert it into the magnitude of velocity
vav = 10.90 m/s
The answer is 10.90 m/s.
However, the question asked for the average velocity and the negative sign of velocity only shows the direction and not the average velocity. Therefore, the magnitude of velocity will be considered as the average velocity which is 10.90 m/s.
To know more about velocity visit-
https://brainly.com/question/30559316
#SPJ11
When a certain metal is illuminated with light of wavelength 300 nm, the emitted photoelectrons have a maximum energy of 2.23eV. Using this data, what is the work function for this metal?
Answer:
The work function for this metal is approximately 3.03 × 10^(-19) J.
Explanation:
The work function (Φ) of a metal represents the minimum energy required to remove an electron from the surface of the metal. It can be calculated using the equation:
Φ = E - E_kin
Where Φ is the work function, E is the energy of the incident photon, and E_kin is the maximum kinetic energy of the emitted photoelectrons.
Given that the wavelength of the incident light is 300 nm and the maximum energy of the emitted photoelectrons is 2.23 eV, we can determine the energy of the incident photon using the equation:
E = (hc) / λ
Where h is the Planck's constant (approximately 6.626 × 10^(-34) J·s), c is the speed of light (approximately 3.00 × 10^8 m/s), and λ is the wavelength.
Converting the wavelength to meters:
λ = 300 nm = 300 × 10^(-9) m
Substituting the values into the equation:
E = (6.626 × 10^(-34) J·s * 3.00 × 10^8 m/s) / (300 × 10^(-9) m)
E ≈ 6.60 × 10^(-19) J
Now we can calculate the work function:
Φ = E - E_kin
Φ = (6.60 × 10^(-19) J) - (2.23 eV * 1.602 × 10^(-19) J/eV)
Φ ≈ 6.60 × 10^(-19) J - 3.57 × 10^(-19) J
Φ ≈ 3.03 × 10^(-19) J
Therefore, the work function for this metal is approximately 3.03 × 10^(-19) J.
Learn more about work function: https://brainly.com/question/14753006
#SPJ11
Why does a negatively charged balloon stick to a wall (neutral object) longer when the air is dry? Vs. when there's moisture in the air.
A negatively charged balloon sticks to a wall (neutral object) longer when the air is dry than when there's moisture in the air due to the following reasons:
The negatively charged balloon exerts an electrostatic force on the wall (neutral object), causing it to stick to the wall. The strength of the electrostatic force is determined by the degree of polarization of the wall's atoms, which is affected by the degree of moisture in the air.When the air is dry, the wall's atoms are less polarized, allowing the balloon to remain in place for an extended period.
The increased polarization of the wall's atoms as a result of increased moisture in the air weakens the electrostatic force exerted by the balloon, resulting in a shorter sticking time.
learn more about electrostatic force
https://brainly.com/question/17692887
#SPJ11
A parallel plate capacitor with plates of area (A) and plate separation (d) is charged so that the potential difference between its plates is (V). While the capacitor is still connected to the power source and its plate separation is increased to 2d, which statement is correct?
The capacitance is increased two times its original value. The voltage between the plates is increased two times its original value. The charge on the plates is increased two times its original value. The voltage between the plates is decreased to one-half its original value. The capacitance is unchanged. The charge on the plates is unchanged. The voltage between the plates is unchanged.
A parallel plate capacitor with plates of area (A) and plate separation (d) is charged so that the potential difference between its plates is (V).
While the capacitor is still connected to the power source and its plate separation is increased to 2d, the capacitance is decreased to one-half its original value. Therefore, the correct option is: The capacitance is decreased to one-half its original value.What is a parallel plate capacitor?A parallel plate capacitor is a two-dimensional capacitor with two metal plates placed parallel to each other. The plates are charged and separated by a small distance. Capacitors are created by keeping two conducting surfaces close together without actually touching each other.
They can store energy by storing electric charge on two oppositely charged plates separated by a dielectric.In the case of a parallel plate capacitor with plates of area (A) and plate separation (d) is charged so that the potential difference between its plates is (V). While the capacitor is still connected to the power source and its plate separation is increased to 2d, then the capacitance is decreased to one-half its original value.
To know more about parallel plate capacitor visit:-
https://brainly.com/question/17511060
#SPJ11
Two charged particles are shown in part (a) of the figure. Particle 1 , with charge q1, is fixed in place at distance d. Particle 2 , with charge q2 can be moved along the x axis. Part (b) of the figure gives the net electric potential V at the origin due to the two particles as a function of the x coordinate of particle 2 . The scale of the x axis is set by x5=24.0 cm. The plot has an asymptote of V=5.76×10−7V as x→[infinity]. What multiple of e gives charge q2? (a) (b) Units
Charge q1, Charge q2, distance d, net electric potential V at the origin due to the two particles as a function of the x coordinate of particle 2 Vx(x).To find: What multiple of e gives charge q2 ?
We have the relation between electric potential and electric field as: E=−dVdxThe electric potential Vx(x) due to the two charges can be obtained using the principle of superposition of electric potentials, that is: Vx(x)=kq1dx−x2+d2+kq2x−d2where, k is Coulomb’s constant=9×109 Nm2/C2Let's differentiate the electric potential function Vx(x) with respect to x.
We get: dVxdx=−kq1(dxd2−x2+d2)−kq2x−d2(dxd2+x−d)dVxdx=−kq1(dxd2−x2+d2)−kq2x−d2(dxd2+x−d)To find charge q2, we need to know the value of dVxdx when x approaches infinity. Therefore, we take the limit of the above expression as x approaches infinity.dVxdx=−kq1d2x−d2+q2x−d2x2dVxdx=−kq1d2x−d2+q2x−d2x2
Taking limit on both sides: limx→∞dVxdx=limx→∞[−kq1d2x−d2+q2x−d2x2]limx→∞dVxdx=0As we have the following asymptote from the plot:Therefore, we get:dVxdx=0−kq1d2x−d2+q2x−d2x2=0⇒kq1d2=x−d2q2⇒q2=q1d24−xThe charge q2 is in terms of q1, d and x. Hence, we can express it in terms of the fundamental charge e. Let the charge q2 be n times the fundamental charge e, then we have:q2=ne Substituting q2=q1d24−x in the above equation:ne=q1d24−xn=eq1d24−xnTherefore, q2=n×e= q1d24−xn
The multiple of e gives charge q2 = q1d24−x where n= q1d24−x.
To know more about charge, visit:
https://brainly.com/question/31173598
#SPJ11
To determine the multiple of e that gives charge q2, you have to use the provided electric potential and the formula for electric potential due to a point charge. You then solve for q2, thinking about the physics of charge interaction.
Explanation:The question relates to the physics concept of electric potential due to charged particles. By definition, the electric potential V at a point is the work done in bringing a unit positive charge from infinity to that point. Since we are given the asymptotic value of electric potential as V=5.76×10−7V, we can use this to calculate the value of the charge q2. Given that e is the electric charge of a single electron (-1.6 x 10^-19 C), we're looking for a multiple of e that represents charge q2. The formula for the electric potential V due to a point charge q at a distance r is V = k*q/r, where k is Coulomb's constant (9 x 10^9 Nm2/C2).
Using this information and the value for the electric potential provided, you can solve for q2, assuming the charge is a multiple of e. Remember that the charge of an electron is negative, so if q2 is a multiple of e it will be a negative number if the charges repel, and positive if they attract.
Learn more about Electric Potential here:https://brainly.com/question/32897214
#SPJ11
A copper wire is 2.111 kilometer long and 1.0−mm in diameter. Using the resistivity of 1.68×10
−8
Ω⋅m, what is the current (Amperes) when the two ends of the wire is connected to an ideal battery with potential of 11.520 volts?
The current flowing through the copper wire is 2.56 A.
Given data:
Length of copper wire = 2.111 km
= 2111 m
Diameter of wire = 1.0 mm
= 0.001 m
Resistivity of copper = 1.68 x 10^-8 Ω⋅m
Battery potential difference = 11.520 V
Formula used:
Resistance of a wire (R) = Resistivity of the material × length of the wire / area of cross-section of the wire
Area of cross-section of the wire = π/4 × (Diameter of the wire)^2
[tex]= \pi/4 \times (0.001 m)^2[/tex]
[tex]= 7.85 \times 10^{-7} m^2[/tex]
Current flowing through the wire (I) = Battery potential difference (V) / Resistance of the wire (R)
Calculation:
Resistance of the wire (R) = Resistivity of copper × length of wire / Area of cross-section of the wire
[tex]= (1.68 \times 10^{-8}\ \Omega.m \times 2111 m) / (7.85 \times 10^{-7}\ m^2)[/tex]
≈ 4.50 Ω
Current flowing through the wire (I) = Battery potential difference (V) / Resistance of the wire (R)
= 11.520 V / 4.50 Ω
≈ 2.56 A
Therefore, the current flowing through the copper wire is 2.56 A.
To know more about current visit
https://brainly.com/question/31315986
#SPJ11
The position of an object of mass 5.0 kg is giving by r = (2m/s4)t4i + (3m/s3)t3j + (4m/s2)t2k. Find the force acting on the object at t = 2 sec.
The force acting on the object at t = 2 sec is F = 96i + 36j + 8k N. To find the force acting on the object at t = 2 sec, we use Newton's second law.
To find the force acting on the object at t = 2 sec, we need to calculate the derivative of the position vector with respect to time to obtain the velocity vector. Then, we can take the derivative of the velocity vector to find the acceleration vector. Finally, using Newton's second law (F = ma), we can calculate the force.
Given the position vector r = (2t^4)i + (3t^3)j + (4t^2)k, we differentiate it once to find the velocity vector v:
v = dr/dt = (d/dt)(2t^4)i + (d/dt)(3t^3)j + (d/dt)(4t^2)k = 8t^3i + 9t^2j + 8t*k.
Next, we differentiate the velocity vector v to find the acceleration vector a:
a = dv/dt = (d/dt)(8t^3)i + (d/dt)(9t^2)j + (d/dt)(8t)k = 24t^2i + 18tj + 8k.
At t = 2 sec, we substitute t = 2 into the acceleration vector to find the force acting on the object:
a(t=2) = 24(2^2)i + 18(2)j + 8k = 96i + 36j + 8k.
Therefore, the force acting on the object at t = 2 sec is F = 96i + 36j + 8k N.
To learn more about Newton's second law click here
https://brainly.com/question/27712854
#SPJ11
what is the volume (in cm3) of a piece of 63.0 g brass? 3 sig fig
The volume of the piece of brass is approximately 7.5 cm³. To determine the volume of a piece of brass, we need to know the density of brass.
To determine the volume of a piece of brass, we need to know the density of brass. The density of brass can vary depending on its composition, but a commonly used value is approximately 8.4 g/cm³. Using this value, we can calculate the volume.
Given:
Mass of brass = 63.0 g
Density of brass = 8.4 g/cm³
To find the volume, we can use the formula:
Volume = Mass / Density
Substituting the given values:
Volume = 63.0 g / 8.4 g/cm³
Calculating the volume:
Volume ≈ 7.5 cm³
Therefore, the volume of the piece of brass is approximately 7.5 cm³.
To learn more about density click here
https://brainly.com/question/29775886
#SPJ11
Pressure is defined as force/area, where the force is applied normal (perpendicular) to the area. When a force is applied tangentially (parallel) to the area, the quantity Force/Area, is called
When a force is applied tangentially (parallel) to the area, the quantity Force/Area is called shear stress.
Shear stress is a measure of the intensity of the internal forces within a material caused by an applied force that acts parallel to a given area. Unlike pressure, which is defined as the force per unit area acting perpendicular to the surface, shear stress occurs when the force is applied tangentially or parallel to the surface. It represents the resistance of a material to deformation under the applied shear force. Shear stress is commonly encountered in situations involving fluid flow, such as when fluids exert a frictional force on a solid surface or when two layers of fluid move at different velocities. In engineering and physics, shear stress plays a crucial role in analyzing the behavior of materials and designing structures to withstand shear forces.
Learn more about shear stress here:
https://brainly.com/question/13034525
#SPJ11
A piano wire has a linear mass denaity of μ=4.15×10
−2
kg/m. Under what terision (inN) must the string be kept to produce waves with a wave speed of 340.00 mist n A piano wire has a linear mass density of μ=4.85×10
−y
kg/m. Under what tension (in N) must the string be kept to produce waves with a wave speed of 5 to on mi/9? N
The tension in the piano wire must be approximately 1.28 N to produce waves with a wave speed of 5.29 m/s. We determine the tension required to produce waves with a given wave speed on a piano wire, we can use the formula for the wave speed on a string:
v = √(T/μ)
where v is the wave speed, T is the tension in the string, and μ is the linear mass density. We can rearrange the formula to solve for T:
T = μ * v^2
μ = 4.85 × 10^-2 kg/m (linear mass density)
v = 5.29 m/s (wave speed)
Substituting the values into the formula, we get:
T = (4.85 × 10^-2 kg/m) * (5.29 m/s)^2
Calculating T, we find:
T ≈1.28 N
To know more about linear mass density, click here:-
https://brainly.com/question/30930552
#SPJ11
(a) What is the speed of each seat (in m/s) ? m/s (b) Draw a diagram of forces acting on a 40.0−kg child riding in a seat. No file chosen This answer has not been graded yet. (c) Find the tension in the chain (in N). You do not need results from part (a) for this. Consider the vertical component of the net force on the child, N What If? The chains holding each seat can withstand a maximum total tenslon of 700 N. (d) What is the angle that the chains make with the vertical (in degrees) when they have this tension? x∘ (e) What is the maximum angular speed (in rad/s) with which the ride can rotate? ∝rad/s
Mass of the child m = 40.0 kg Total tension that can be applied by the chains
T = 700 N
The speed of each seat (in m/s) can be calculated using the formula:
v² = rω
where v is the speed of the seat,
r is the radius of the circular path and ω is the angular speed.
We know that the radius of the circular path is given by:
r = 5.00 m
So, the angular speed can be calculated as:
ω = v/r
Solving for v,
we get:
v = rω
Hence,
the speed of each seat (in m/s) is given by:
v = rω = 5.00 × 2.50 = 12.5 m/s(b)
The diagram of the forces acting on a 40.0 kg child riding in a seat is as follows:
In the diagram, the weight of the child is acting downwards and is equal to:
mg = 40.0 × 9.8 = 392 N
The tension in the chain is acting upwards and is equal to T.
The net force acting on the child is equal to the difference between the weight of the child and the tension in the chain, i.e.,
F net = T - mg equals to
F net = 700 - 392 = 308 N
So, the net force acting on the child is 308 N and is acting towards the center of the circular path.
The child is thus experiencing a centripetal force of 308 N.
We know that the net force acting on the child is given by:
F net = T - mg
At the bottommost point, the net force acting on the child is equal to the centripetal force acting on it.
So, the net force is equal to:
F net = mv²/r
where v is the speed of the child at the bottommost point and r is the radius of the circular path.
the given values,
we get:
mv²/r = T - mg
Substituting the values of m and g,
we get:
40.0v²/5.00 = T - 392
Simplifying,
we get:
T = 40.0v²/5.00 + 392
T = 8v²/1 + 392
Now, we know that the total tension that can be applied by the chains is equal to 700 N.
the maximum angular speed with which the ride can rotate is 1.58 rad/s.
To know more about tension visit:
https://brainly.com/question/10169286
#SPJ11
