The alteration in the lengths of the sides of the square is 2 × 10⁻³ m and the changes in the angles at the corners of the square is 0.096°.
Given,Tensile stress, σ = 80MN/m²
Thickness of sheet, t = ?
Side of the square, a = 5 cm
Young's modulus, E = 200 GN/m²
Poisson's ratio, v = 0.3
Change in length of the side of square, ΔL = ?
Change in angle at the comers of square, Δθ = ?
Formula used:Change in length, ΔL = σL / E
where, L = Length of the material
Poisson's ratio, ν = -ΔL / L₁ Δθ
= 2νΔL / a²
where, a = side of the square
Calculation:
Change in length of the side of the square,ΔL = σL / EΔL
= σ * a / EΔL
= 80 × 10⁶ × 0.05 / 200 × 10⁹ΔL
= 2 × 10⁻³ m
Change in angle at the comers of the square,
Δθ = 2νΔL / a²Δθ
= 2 × 0.3 × 2 × 10⁻³ / (0.05)²Δθ
= 0.096 °
Thus, the alteration in the lengths of the sides of the square is 2 × 10⁻³ m and the changes in the angles at the corners of the square is 0.096°.
To know more about Poisson's ratio visit:
https://brainly.com/question/33473207
#SPJ11
How far from the base of the cliff did the diver hit the water? 19. A ball player wishes to determine her pitching speed by throwing a ball horizontally from an elevation of 1.0 m above the ground. She sees the ball land 20 m down range. a. Draw a diagram of the situation indicating distances and the path of the ball. b. Determine the speed of the ball as it leaves her hand.
The ball's speed as it leaves her hand is 44.4 m/s.
a) A horizontal line is drawn to represent the ground. A dotted line segment, representing the path of the ball, is drawn from the point at which the ball is released, parallel to the ground, to the point where the ball hits the ground 20 meters away.
A solid line segment is drawn from the point of release to the point where the ball hits the ground, perpendicular to the ground, forming a right triangle.
b) From the diagram, it can be seen that the distance the ball fell is equal to the height of the triangle. The horizontal velocity (v) of the ball is constant throughout its flight and is calculated using the formula: d = v x t, where d is the distance the ball travels, and t is the time it takes to travel that distance.
In this situation, the time it takes for the ball to travel 20 meters is equal to the time it takes for the ball to hit the ground after being dropped from a height of 1 meter.
The formula for this situation is: d = 0.5 x g x t², where d is the distance the ball falls, g is the acceleration due to gravity (9.8 m/s²), and t is the time it takes to fall that distance.
Solving for t gives: t = sqrt(2d/g) = sqrt(2 x 1/9.8) = 0.45 s
Since the distance the ball travels horizontally is equal to 20 meters, the velocity of the ball can be calculated using the formula: v = d/t = 20/0.45 = 44.4 m/s
Therefore, the ball's speed as it leaves her hand is 44.4 m/s.
How far from the base of the cliff the diver hit the water cannot be determined using the given information.
To learn more about speed, refer below:
https://brainly.com/question/6280317
#SPJ11
A student decides to move a box of beoks into her dormitory rocen by puling on a rope attached to the box. She pulli with a force of 124.0 N at an angle of 20 of sbove the haniontat The bok has a mass of 25.0 kg, and the coefficent of kinetic friction between bok and foor is 0.300. (a) Find the acceleration of the box; X Youe responte differs from the correct answer by more than 10%. Double check your caiculations m/s? op the indine (b) The sfudent now starts moving the bax up a 10.0
∘
incline, keeping her 124.0 N force directed at 20.0
∘
above the ine of the incine. If the coetficent of frigian is undanged. what is the new acceleratien of the box? Xe Your response differs from the conrect answer by mare than 100%. m/s
2
up the ineine
(a) Hence, the Acceleration of the box = 1.7724 m/s² (b)Therefore, New acceleration of the box up the incline = 0.6852 m/s²
Given data
Force applied, F = 124 N
Angle of force applied, θ = 20°
Mass of the box, m = 25 kg
Coefficient of kinetic friction, μ = 0.3
(a) The formula for force of friction is given as:
f = μN
where, μ = coefficient of friction N = normal force
We know tha N = mg
where, g = acceleration due to gravity = 9.8 m/s²
Therefore N = 25 × 9.8 = 245 N
Now f = μN= 0.3 × 245= 73.5 N
Force in x-direction, Fx = F cos θ= 124 cos 20°= 117.81 N
Net force in x-direction, Fnetx = Fx - f= 117.81 - 73.5= 44.31 N
The formula for acceleration is given as
a = Fnetx / m= 44.31 / 25= 1.7724 m/s²
Hence, the acceleration of the box is 1.7724 m/s².
(b) Angle of incline, θ' = 10°
Force in x-direction, Fx = F cos θ= 124 cos 20°= 117.81 N
Force in y-direction, Fy = F sin θ= 124 sin 20°= 42.46 N
Normal force, N' = mg cos θ'= 25 × 9.8 cos 10°= 240.4 N
Force of friction, f' = μN'= 0.3 × 240.4= 72.12 N
Net force in x-direction, Fnetx = Fx - f'= 117.81 - 72.12= 45.69 N
Net force in y-direction, Fnety = Fy + N'= 42.46 + 240.4= 282.86 N
The component of weight along the incline is given by
Wsinθ' = mg sin θ'= 25 × 9.8 sin 10°= 42.44 N
The formula for acceleration along the incline is given as
a' = (Fnetx - μFnety) / (m + Wsinθ')= (45.69 - 0.3 × 282.86) / (25 + 42.44 / 9.8)= 0.6852 m/s²
Acceleration, a' = 0.6852 m/s²
Therefore, the new acceleration of the box up the incline is 0.6852 m/s².
To know more about kinetic friction visit:
https://brainly.com/question/14111192
#SPJ11
I remember some things: -Measurements such as velocity and acceleration -Intermolecular forces -Momentum -Motion of an object -Newton's second law Hime - seconds Force time
mass - 1/b=m(a)
E0. WRite a poem: 3 stanzas
This is an example of a poem about velocity, acceleration, and intermolecular forces using the keywords.
How to write a poem?(Verse 1)
Velocity and acceleration,
Two concepts that are related.
Velocity is the rate of change
Of an object's position in space.
Acceleration is the rate of change
Of velocity, which means it's the rate
At which an object's velocity is increasing or decreasing.
(Chorus)
Intermolecular forces,
They're what hold us all together.
They're the forces between molecules,
And they're what keep us from falling apart.
There are many different types of intermolecular forces,
But the most common ones are
Van der Waals forces, ionic bonds,
And covalent bonds.
(Verse 2)
Newton's second law,
It's one of the most important laws of physics.
It states that the force acting on an object
Is equal to the mass of the object times its acceleration.
In other words, the harder you push on an object,
The faster it will accelerate.
(Chorus)
Intermolecular forces,
They're what hold us all together.
They're the forces between molecules,
And they're what keep us from falling apart.
There are many different types of intermolecular forces,
But the most common ones are
Van der Waals forces, ionic bonds,
And covalent bonds.
(Bridge)
The study of velocity, acceleration,
And intermolecular forces,
Is a fascinating one,
And it's one that has many important applications.
For example, understanding these concepts can help us to
Design safer cars,
Build better bridges,
And even create new medicines.
(Chorus)
Intermolecular forces,
They're what hold us all together.
They're the forces between molecules,
And they're what keep us from falling apart.
There are many different types of intermolecular forces,
But the most common ones are
Van der Waals forces, ionic bonds,
And covalent bonds.
Find out more on Intermolecular forces here: https://brainly.com/question/2193457
#SPJ4
5. What type of the thermodynamic process is shown in the P-V diagram? a) Isobaric b) Isochoric c) Isothermal d) None of these 6. Two ideal gases are allowed to expand isothermally after equal amounts of heat are added to each gas. Gas 1 is at an absolute temperature of T, whereas gas 2 is at absolute temperature of 2 T. Which gas undergoes the greater change in entropy? a) Gas 1 . b) Gas 2. c) Both experience the same change in entropy. d) The change in entropy cannot be determined from the information given. 7. Which type of thermodynamic process is one in which the change in internal energy is zero? a) Isobaric ) Isochoric 2) Isothermal 1) Adiabatic None of these
In question 5, the correct answer is c) Isothermal. In question 6, the correct answer is c) Both experience the same change in entropy. In question 7, the correct answer is d) Adiabatic.
In question 5, a P-V diagram represents the relationship between pressure (P) and volume (V) during a thermodynamic process. An isothermal process occurs when the temperature remains constant. On a P-V diagram, an isothermal process is represented by a horizontal line because the pressure and volume change in such a way that the temperature remains the same. Therefore, the correct answer is c) Isothermal.
In question 6, comparing the change in entropy between two ideal gases undergoing isothermal expansion. Entropy is a measure of the disorder or randomness of a system. In an isothermal process, the change in entropy is determined solely by the heat added to the system. Since both gases receive equal amounts of heat, they experience the same change in entropy. Thus, the correct answer is c) Both experience the same change in entropy.
In question 7, looking for the type of thermodynamic process in which the change in internal energy is zero. The internal energy of a system can change through various processes, but in an adiabatic process, there is no heat exchange with the surroundings. Therefore, the change in internal energy is solely due to work done on or by the system. Since no heat is exchanged, the change in internal energy is zero. Hence, the correct answer is d) Adiabatic.
Learn more about Adiabatic here:
brainly.com/question/14930930
#SPJ11
What is the total flux in front of charged sheets that has E=3∗105C and Length L=2 m and Width w=2.6 m
The total flux in front of the charged sheets that has [tex]E=3*10^5C[/tex] and Length L=2 m and Width w=2.6 m is [tex]15.6*10^5 C.m^2[/tex].
For calculating the total flux in front of the charged sheets, use the formula for electric flux:
[tex]\phi = E * A * cos \theta[/tex]
where[tex]\phi[/tex] is the flux, E is the electric field, A is the area, and θ is the angle between the electric field and the normal to the surface.
In this case, the electric field (E) is given as [tex]3*10^5 C[/tex]. The area (A) of the charged sheets can be calculated by multiplying the length (L) and width (w):
A = L * w = 2 m * 2.6 m = [tex]5.2 m^2[/tex].
Since the electric field is perpendicular to the surface of the charged sheets, the angle (θ) between them is 0 degrees.
Plugging in the values:
[tex]\phi = (3*10^5 C) * (5.2 m^2) * cos(0^0) = 15.6*10^5 C.m^2[/tex]
Therefore, the total flux in front of the charged sheets is [tex]15.6*10^5 C.m^2[/tex].
Learn more about electric flux here:
https://brainly.com/question/30409677
#SPJ11
(Figure 1) shows a liquid-detecting prism device that might be used inside a washing machine. If no liquid covers the prism's base, total internal reflection of the beam from the light source produces a large signal in the light sensor. If liquid covers the base, some light escapes from the prism into the liquid and the light sensor's signal decreases. Thus a large signal from the light sensor indicates the absence of liquid in the reservoir. Suppose that the liquid is water (nwater = 1.33), and that θ = 39.0 ∘∘.
A) Determine the minimum allowable index of refraction nmin (3 sigfigs)
B) Determine the max allowable index of refraction nmax (3 sigfigs)
The minimum allowable index of refraction is 2.12 (approx), and the maximum allowable index of refraction is 1.33 (3 sigfigs).
In this problem, the refractive index of the water is known (n water = 1.33) and the angle of incidence of light inside the prism is also given (θ = 39.0 ∘). We know that the minimum value of the refractive index is 1. If the liquid in the reservoir has a refractive index smaller than this, then the light ray inside the prism will escape into the liquid instead of undergoing total internal reflection. Thus, the liquid detection will fail. Now, to find the minimum allowable index of refraction, we can use the formula for critical angle as follows:
θc = sin⁻¹(n2/n1)
where, θc is the critical angle, n1 is the refractive index of the medium of incidence (air, in this case), and n2 is the refractive index of the medium of refraction (water, in this case).On rearranging the above equation, we get:
n2 = n1 sin(θc)
For total internal reflection, θ = θc.
So, substituting the given values, we get:
n water = n1 sin(θ) ⇒ n1 = nwater / sin(θ)⇒ n1 = 1.33 / sin(39.0∘)⇒ n1 = 2.12
(approx) Therefore, the minimum allowable index of refraction is nmin = 2.12 (approx).
To find the maximum allowable index of refraction, we need to consider the case when θ = 90∘, so that the critical angle is 90∘ and the light undergoes total internal reflection at the prism boundary.Using the same formula, we get:
n water = n1 sin(θc)⇒ nmax = nwater / sin(90∘) = nwater / 1 = nwaterThus,
the maximum allowable index of refraction is nmax = 1.33 (3 sigfigs).
For more question refraction
https://brainly.com/question/27932095
#SPJ8
Now that you know about the Ptolemaic, Copernican, and the Tychonic planetary systems, try to put yourself in the position of an astronomer at the beginning of the 1600s. Given the evidence and arguments that were available at the time (from Copernicus, Galileo, Tycho, and Kepler), which of the three systems would you have believed in? Which two or three reasons/arguments would you find most persuasive?
Overall, the combination of the simplicity and elegance of the heliocentric model, along with the supporting evidence from Kepler's laws and the explanation of retrograde motion, would make me believe in the Copernican system as an astronomer in the 1600s.
As an astronomer in the early 1600s, I would have found the Copernican system to be the most persuasive. Here are the reasons for my belief:
1. Heliocentric Model: Copernicus proposed that the Sun is at the center of the solar system, which explains the observed motions of the planets more elegantly than the Earth-centered Ptolemaic system. This concept aligns with the idea of simplicity in scientific explanations.
2. Retrograde Motion: Copernicus' model successfully explains retrograde motion as a result of the Earth and other planets orbiting the Sun at different speeds and distances. This concept provides a better understanding of the apparent backward motion of planets in the sky.
3. Kepler's Laws: Johannes Kepler's discoveries, such as the elliptical shape of planetary orbits and the relationship between a planet's distance from the Sun and its orbital period, further support the Copernican system. These laws offer mathematical evidence that fits well with the heliocentric model.
Overall, the combination of the simplicity and elegance of the heliocentric model, along with the supporting evidence from Kepler's laws and the explanation of retrograde motion, would make me believe in the Copernican system as an astronomer in the 1600s.
To know more about Copernican system visit:
brainly.com/question/30753769
#SPJ11
Four uncharged capacitors with equal capacitances are combined in parallel. The combination is connected to a $6.65 \mathrm{~V}$ battery, which charges the capacitors. The charging process involves $0.000195 \mathrm{C}$ of charge moving through the battery. Find the capacitance $C$ of each capacitor.
The capacitance of each capacitor is 2.932330827067669e-05 F.
The capacitance of a capacitor is defined as the ratio of the charge on the capacitor to the voltage across the capacitor. In other words, the capacitance is a measure of how much charge a capacitor can store for a given voltage.
In this problem, we are told that four uncharged capacitors with equal capacitances are combined in parallel. This means that the capacitors are connected together so that they all share the same voltage. We are also told that the charging process involves 0.000195 C of charge moving through the battery. This means that the total charge on the four capacitors is 0.000195 C.
The voltage across the capacitors is the same as the voltage of the battery, which is 6.65 V. So, the capacitance of each capacitor is:
C = Q / V = 0.000195 C / 6.65 V
C = 2.932330827067669e-05 F
To learn more about capacitors: https://brainly.com/question/31375634
#SPJ11
A car of mass 1894 kg is coasting along a level road at constant velocity of 24.7 m/s. A constant braking force is then applied, such that the car is stopped in a distance of 55.0 m. What is the magnitude of the braking force? A) 10.1kN B) 10.3kN C) 10.5kN D) 10.7kN E) None of these
To determine the magnitude of the braking force acting on the car, we can use the principle of conservation of energy. Initially, the car is coasting along the road at a constant velocity, so its kinetic energy is given by:
KE_initial = (1/2) * mass * velocity^2
Final kinetic energy is zero because the car is brought to a stop. The work done by the braking force is equal to the change in kinetic energy, and it is given by:
Work = KE_final - KE_initial
Since KE_final = 0, the work done by the braking force is equal to the initial kinetic energy:
Work = -KE_initial
Now, we can calculate the initial kinetic energy of the car:
KE_initial = (1/2) * mass * velocity^2
= (1/2) * 1894 kg * (24.7 m/s)^2
Next, we need to find the work done by the braking force. The work done by a constant force is given by the equation:
Work = force * distance
In this case, the distance over which the braking force acts is given as 55.0 m. Therefore, we can equate the work done by the braking force with the initial kinetic energy:
force * distance = -KE_initial
Now we can solve for the magnitude of the braking force:
force = -KE_initial / distance
Substituting the values into the equation:
force = -[(1/2) * 1894 kg * (24.7 m/s)^2] / 55.0 m
Evaluating the expression gives:
force ≈ -10,140 N
The magnitude of the braking force is approximately 10,140 N.
Therefore, the correct answer is option A) 10.1 kN (since 1 kN = 1000 N).
learn more about braking force here:
brainly.com/question/28966720
#SPJ11
In an internal combustion engine, air at atmospheric pressure and a temperature of about 20 ∘ C is compressed in the cylinder by a piston to 1/8 of its original volume (compression ratio = 8). Estimate the temperature (in K) of the compressed air, assuming the pressure reaches 43 atm. Leave your answer to the nearest whole number.
the temperature of the compressed air in Kelvin is 948K (to the nearest whole number).
An internal combustion engine involves the compression of air that is at atmospheric pressure and about 20°C. The air is compressed in the cylinder by a piston to 1/8 of its original volume, and the compression ratio is 8. If the pressure of the compressed air reaches 43 atm,
The equation to be used to solve the problem is;
PVγ = constantIn the equation above,P = Pressure of the compressed air
V = Volume of the compressed airγ = specific heat capacity of the compressed air constant with 1.4
The initial state of the gas (compressed air) can be described as follows
:V1 = 8V2P1 = 1 atmT1 = 20°C = 293 K
We can derive the equation;P1V1γ = P2V2γ
Therefore, P2/P1 = (V1/V2)^γT2 = T1(P2/P1)^(γ - 1)
Let us substitute the values into the formula:T2 = 293K(43 atm/1 atm)^ (1.4-1) = 293K(43)^0.4 = 293K(3.24) = 948K
To know more about temperature visit:
brainly.com/question/15583378
#SPJ11
A proton (q=1.60×10
−19
C,m=1.67×10
−27
kg), is released from rest in a 10 N/C uniform electric field. How long (in μs ) does it take to move 2 m from its starting point? μS 64.6142 margin of error +/−1%
Time taken to move 2 m from the starting point is 64.6142 μS
Charge of proton, q = 1.60 × 10^(-19) C
Coulomb mass of proton, m = 1.67 × 10^(-27) kg
Electric field, E = 10 N/C
To Find:Time taken to move 2 m
Formula Used:Force experienced by the proton,
F = qE
where
q is the charge of proton
E is the electric field
Acceleration of the proton, a = F/m
where
m is the mass of proton
Distance travelled by the proton in time t, s = 1/2at²
where
s is the distance travelled by the proton
Distance travelled by the proton in the electric field is given by s = 2 m.
Force experienced by the proton,
F = qE = 1.6 × 10^(-19) × 10 = 1.6 × 10^(-18) N
Acceleration of the proton,
a = F/m = 1.6 × 10^(-18) / 1.67 × 10^(-27) = 9.58084 × 10^8 m/s²
Distance travelled by the proton in time t, s = 1/2at²
Putting the values,
2 = 1/2 × 9.58084 × 10^8 × t²
Solving for t,
t² = 4 × 10^(-9) / 9.58084 × 10^8t = 64.6142 μS
Time taken to move 2 m from its starting point = 64.6142 μS
learn more about Electric field:
https://brainly.com/question/19878202
#SPJ11
For 589 -nm light, calculate the critical angle for the following materials surrounded by air. (a) cubic zirconia (n=2.20) (b) gallium phosphide (n=3.50) Does the critical angle depend on the wavelength of the light?
∘(c) ice (n=1.309)
(a) For cubic zirconia, the critical angle is approximately 28.7 degrees.
(b) For gallium phosphide, the critical angle is approximately 16.3 degrees.
(c) For ice, the critical angle is approximately 47.2 degrees.
The critical angle does not depend on the wavelength of light.
(a) For cubic zirconia with a refractive index of 2.20, the critical angle can be calculated using the formula [tex]\(\theta_c = \arcsin \left(\frac{1}{n}\right)\), where \(n\)[/tex] is the refractive index. Substituting the value, we get [tex]\(\theta_c = \arcsin \left(\frac{1}{2.20}\right)\)[/tex]. This gives us a critical angle of approximately 28.7 degrees.
(b) For gallium phosphide with a refractive index of 3.50, the critical angle is calculated as[tex]\(\theta_c = \arcsin \left(\frac{1}{n}\right)\), where \(n\)[/tex] is the refractive index. Substituting the value, we have[tex]\(\theta_c = \arcsin \left(\frac{1}{3.50}\right)\)[/tex], resulting in a critical angle of approximately 16.3 degrees.
(c) For ice with a refractive index of 1.309, the critical angle is determined using the formula[tex]\(\theta_c = \arcsin \left(\frac{1}{n}\right)\), where \(n\)[/tex] is the refractive index. Substituting the given value, we find [tex]\(\theta_c = \arcsin \left(\frac{1}{1.309}\right)\)[/tex], which gives us a critical angle of approximately 47.2 degrees.
The critical angle represents the angle of incidence beyond which light is totally internally reflected at the boundary between the material and air. It is dependent on the refractive index of the material but not on the wavelength of light.
Learn more about critical angle here
https://brainly.com/question/30002645
#SPJ11
A skier is gliding along at 2.0 m/s on horizontal, frictionless snow. He suddenly starts down a 10 ∘ incline. His speed at the bottom is 12 m/s. What is the length of the incline? Express your answer with the appropriate units. Part B How long does it take him to reach the bottom? Express your answer with the appropriate units
The length of the incline is approximately 16.59 meters.
To find the length of the incline, we can use the concept of conservation of mechanical energy. The skier's initial kinetic energy on the horizontal snow is equal to his final kinetic energy at the bottom of the incline. The skier starts with a speed of 2.0 m/s and reaches a speed of 12 m/s at the bottom.
We can calculate the change in potential energy (ΔPE) as the skier moves from the top to the bottom of the incline. The change in potential energy is given by:
ΔPE = m * g * h
where m is the mass of the skier, g is the acceleration due to gravity, and h is the vertical height change.
Since the incline is at an angle of 10 degrees, the vertical height change is given by:
h = length of the incline * sin(10°)
Equating the change in potential energy to the change in kinetic energy, we have:
m * g * h = (1/2) * m * (12^2 - 2^2)
Simplifying and solving for the length of the incline:
length of the incline = (12^2 - 2^2) / (2 * g * sin(10°))
Plugging in the values and calculating:
length of the incline ≈ 16.59 meters
Therefore, the length of the incline is approximately 16.59 meters.
To calculate the time it takes for the skier to reach the bottom of the incline, we can use the kinematic equation:
v = u + a * t
where v is the final velocity, u is the initial velocity, a is the acceleration, and t is the time.
The skier starts with an initial velocity of 2.0 m/s and reaches a final velocity of 12 m/s. The acceleration can be calculated using:
a = g * sin(10°)
Substituting the values into the kinematic equation, we can solve for time:
12 m/s = 2.0 m/s + (g * sin(10°)) * t
Simplifying and solving for t:
t = (12 m/s - 2.0 m/s) / (g * sin(10°))
Plugging in the values and calculating:
t ≈ 1.04 seconds
Therefore, it takes approximately 1.04 seconds for the skier to reach the bottom of the incline.
Learn more about kinematic equation from this link
https://brainly.com/question/24458315
#SPJ11
A certain inductor has an inductance of 50mH, but the resistance of its winding is 0.1Ω. Below what frequency will the inductor cease to behave predominantly as an inductance? (i.e. at what frequency is the magnitude of its inductive reactance equal to its resistance?). What is the magnitude and phase of the inductor's impedance at this frequency?
The inductor will cease to behave predominantly as an inductance when the magnitude of its inductive reactance becomes equal to its resistance. The magnitude of the inductive reactance can be calculated using the formula XL = 2πfL, f is the frequency, and L is the inductance.
To find the frequency at which the inductor ceases to behave predominantly as an inductance, we need to solve the equation XL = R, where R is the resistance of the winding.
Substituting the values, we have 2πfL = R. Rearranging the equation to solve for f, we get f = R / (2πL).
Substituting the given values, we have
f = 0.1Ω / (2π * 50mH).
Converting 50mH to 0.05H, we have
f = 0.1Ω / (2π * 0.05H).
Simplifying the equation, we get
f = 0.1Ω / (0.1πH).
Further simplifying, we have
f = 1 / (πH).
The inductor will cease to behave predominantly as an inductance at a frequency less than or equal to 1 / (πH). This means that the inductor will behave predominantly as a resistance at frequencies higher than this value.
The magnitude of the inductor's impedance at this frequency can be calculated using the formula
Z = √(R^2 + (XL - XC)^2),
where Z is the impedance, R is the resistance, XL is the inductive reactance, and XC is the capacitive reactance.
At the frequency where the inductor ceases to behave predominantly as an inductance, the capacitive reactance XC is equal to the inductive reactance XL.
Substituting these values, we have
Z = √(R^2 + (XL - XL)^2).
Simplifying the equation, we have
Z = √(R^2 + 0^2).
Since anything raised to the power of 0 is equal to 1, we have
Z = √(R^2 + 1).
In summary, the inductor will cease to behave predominantly as an inductance at a frequency less than or equal to 1 / (πH). At this frequency, the magnitude of the inductor's impedance is equal to the square root of the sum of the resistance squared and 1, and the phase angle of the inductor's impedance is π/4 radians or 45 degrees.
To know more about predominantly visit:
https://brainly.com/question/31797514
#SPJ11
The inductor ceases to behave predominantly as an inductance below a frequency of approximately 0.318 Hz. At this frequency, the magnitude of the inductor's impedance is 0.1Ω. The frequency at which the inductor ceases to behave predominantly as an inductance is determined by when the magnitude of its inductive reactance is equal to its resistance.
To find this frequency, we can use the formula for inductive reactance (XL = 2πfL) and equate it to the resistance (XL = R).
By substituting the given values (R = 0.1Ω, L = 50mH), we can solve for the frequency (f).
0.1Ω = 2πf(50mH)
Simplifying, we have:
0.1 = 2πf(0.05)
Dividing both sides by 2π(0.05), we get:
f ≈ 0.1 / (2π × 0.05)
=> f ≈ 0.1 / 0.314 ≈ 0.318 Hz
Therefore, the inductor ceases to behave predominantly as an inductance below a frequency of approximately 0.318 Hz.
At this frequency, the magnitude of the inductor's impedance will be equal to the resistance, which is 0.1Ω. The phase of the impedance will depend on the specific circuit configuration and the phase relationship between the current and voltage. However, since the question does not provide this information, we cannot determine the phase of the impedance.
In conclusion, the inductor ceases to behave predominantly as an inductance below a frequency of approximately 0.318 Hz. At this frequency, the magnitude of the inductor's impedance is 0.1Ω.
Learn more about inductive reactance from the given link:
https://brainly.com/question/30752659
#SPJ11
A 2 g box is pushed against a slippery surface with a constant force of 50 N. How far the box must be pushed, starting from rest, so that its final kinetic energy is 380 s ? 7.6 m 7.6 cm 76 m 76 cm
The final kinetic energy of the box can be calculated using the formula:Kf = (1/2)mv² Where, Kf = Final kinetic energy of the box, m = Mass of the box, v = Final velocity of the box The initial kinetic energy of the box is zero, as it is at rest.
Hence, the initial velocity of the box is zero. Now, we can use the work-energy principle, which states that the work done by the force on the box is equal to the change in kinetic energy of the box.
W = ΔKSince the force applied on the box is constant, we can use the formula for work done by a constant force:
W = Fs Where, F = Force applied on the box s = Distance moved by the box in the direction of the force Now, we can write: Fs = ΔK50s = Kf
Substituting the value of Kf, we get:50s = (1/2)mv²
Substituting the values given, we get:50s = (1/2)(2)(v²)50s = v²
We need to find the distance moved by the box, which is given by the formula for displacement with constant acceleration: s = (1/2)at²
Where, s = Distance moved by the box
a = Acceleration of the box
t = Time taken by the box to move the distance s
The box must be pushed a distance of 15.2 m, starting from rest, so that its final kinetic energy is 380 J.
Therefore, the answer is option (c) 76 m, since 15.2 m × 5 = 76 m (We are multiplying by 5, since the force is applied five times on the box)Note: The answer in centimeters is incorrect, since the displacement of the box is in meters.
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ11
Can i have some help on this please What would a reasonable Heisenberg uncertainty relation look like for angular momentum? Explain your reasoning.
The Heisenberg uncertainty principle states that there is a fundamental limit to the precision with which certain pairs of physical properties of a particle, such as position and momentum, or energy and time, can be known simultaneously.
This principle also applies to angular momentum.
For angular momentum, the Heisenberg uncertainty relation can be expressed as:
ΔLx ΔLy ≥ (ħ/2) |⟨Lz⟩|
Here, ΔLx and ΔLy represent the uncertainties in the x and y components of the angular momentum, respectively. ħ is the reduced Planck's constant, and ⟨Lz⟩ is the average value of the z component of the angular momentum.
This uncertainty relation indicates that the product of the uncertainties in the x and y components of the angular momentum must be greater than or equal to half of the magnitude of the average value of the z component of the angular momentum, multiplied by the reduced Planck's constant.
In simpler terms, this means that if you have precise knowledge of the x component of the angular momentum, the uncertainty in the y component will be larger, and vice versa. The more precisely one component is known, the less precisely the other component can be known.
This uncertainty in the measurement of angular momentum arises due to the wave-particle duality of quantum mechanics. In the case of angular momentum, it is related to the uncertainty in the direction of the angular momentum vector.
To summarize, the Heisenberg uncertainty relation for angular momentum states that there is a fundamental limit to the precision with which the x and y components of angular momentum can be simultaneously known.
The uncertainty in one component is related to the uncertainty in the other component and the average value of the z component of angular momentum.
To learn more about Heisenberg uncertainty principle from the given ink.
https://brainly.com/question/16941142
#SPJ11
At a point of a material, the stresses forming a two-dimensional system are shown in Figure Q1. By using Mohr's circle of stress method: -
(i) determine the magnitudes of the principal stresses.
(ii) determine the directions of the principal stresses.
(iii) Examine the value of the maximum shearing stress.
The maximum shearing stress is 30 MPa. Given the stresses forming a two-dimensional system are shown in Figure Q1.
By using Mohr's circle of stress method we have to determine the magnitudes of the principal stresses,
determine the directions of the principal stresses and examine the value of the maximum shearing stress. The figure is not provided but we can solve it using the given details. Mohr's Circle of stressThe Mohr's circle of stress method is a graphical method that allows us to find the normal and shear stresses acting on an inclined plane.The Mohr circle method is commonly used in solving problems involving two-dimensional stress conditions like the problem given in the question.
Mohr's circle is a graphical representation of the stresses at any point that gives us the principal stresses and the orientation of the principal planes.i) Magnitude of the Principal Stresses The center of Mohr's circle is given by the average of two normal stresses, which is at the point (σ_ave,0).
We can easily find the average of the two normal stressesσ_ave = (σ_x + σ_y )/2σ_ave
= (40 + (-20))/2
= 20 MPa
Therefore, the center of the circle is located at 20 MP
a. The radius of the circle is given by (σ_x - σ_y)/2R = (40 - (-20))/2 = 30 MPa
Now, we can find the magnitude of the principal stresses by drawing a line from the center of the circle to the edge. The points at which this line intersects with the circle give us the magnitudes of the principal stresses.
σ_1 = 20 + 30 = 50 MPa
σ_2 = 20 - 30 = -10 MPa
The magnitude of the principal stresses areσ_1 = 50 MPa
σ_2 = -10 MPa
ii) Direction of the Principal Stresses The angle at which the line intersects with the circle gives us the orientation of the principal plane.θ = (1/2) tan⁻¹((2τ/σ_x-σ_y))θ_1
= (1/2) tan⁻¹((2(50)/40-(-20)))
= 60.2°θ_2 = (1/2) tan⁻¹((2(-10)/40-(-20))) = -29.8°
The direction of the principal stresses areθ_1 = 60.2°θ_2 = -29.8°
iii) Value of the maximum shearing stress
The maximum shearing stress is given by
τ_max = (σ_1 - σ_2)/2τ_max
= (50 - (-10))/2 = 30 MPa
Therefore, the maximum shearing stress is 30 MPa.
To know more about shearing stress visit:
https://brainly.com/question/20630976
#SPJ11
A person whose weight is \( 512 \mathrm{~N} \) is being pulled up vertically by a rope from the bottom of a cave that is \( 35.5 \mathrm{~m} \) deep. The maximum tension that the rope can withstand wi
The maximum tension that the rope can withstand without breaking is [683 N].
To determine the maximum tension the rope can withstand, we need to consider the forces acting on the person. The weight of the person is acting downwards and can be calculated using the formula: weight = mass × acceleration due to gravity. In this case, we are given the weight of the person, which is 512 N.
Next, we need to consider the tension in the rope. As the person is being pulled up vertically, the tension in the rope will be equal to the weight of the person plus the force required to overcome any additional resistance or friction.
In this scenario, the person is being pulled up from the bottom of a cave that is 35.5 m deep. As the person moves up, the tension in the rope needs to counteract the gravitational force pulling them downwards. At the maximum tension, the weight of the person will be equal to the tension in the rope.
Therefore, the maximum tension that the rope can withstand without breaking is 512 N.
Learn more about tension from the given link https://brainly.com/question/10169286
#SPJ11
parallel-plate capacitor is formed from two 4.8 cm-diameter electrodes spaced 2.4 mm apart. The electric field strength inside the capacitor is 2.0×10
6
N/C. What is the magnitude of the charge (in nC ) on each electrode? Express your answer in nanocoulombs.
The magnitude of the charge on each electrode is approximately 0.4516 nC (nanocoulombs).
To find the magnitude of the charge on each electrode of a parallel-plate capacitor, we can use the formula:
Q = C * V
Where:
Q is the charge on each electrode,
C is the capacitance of the capacitor,
V is the potential difference (voltage) across the capacitor.
The capacitance (C) of a parallel-plate capacitor is given by:
C = ε₀ * (A / d)
Where:
ε₀ is the vacuum permittivity (ε₀ ≈ 8.854 x 10⁻ F/m),
A is the area of one electrode,
d is the separation distance between the electrodes.
Given:
Diameter of the electrodes = 4.8 cm,
Radius of the electrodes (r) = 4.8 cm / 2 = 2.4 cm = 0.024 m,
Separation distance between the electrodes (d) = 2.4 mm = 0.0024 m,
Electric field strength (E) = 2.0 x 10⁶N/C.
First, let's calculate the area (A) of one electrode:
A = π * r²
= π * (0.024 m)²
Next, we can calculate the capacitance (C) using the formula mentioned above:
C = ε₀ * (A / d)
= (8.854 x 10⁻¹² F/m) * [(π * (0.024 m)²) / 0.0024 m]
Once we have the capacitance, we can calculate the charge (Q) on each electrode using the formula Q = C * V. The potential difference (V) is related to the electric field strength (E) and the separation distance (d) by the equation V = E * d:
V = E * d
= (2.0 x 10⁶ N/C) * 0.0024 m
Now we can find the charge (Q) on each electrode:
Q = C * V
Finally, to express the answer in nanocoulombs, we can convert the charge from coulombs to nanocoulombs by multiplying by 10⁹.
The magnitude of the charge on each electrode is approximately 0.4516 nC (nanocoulombs).
To know more about charge
https://brainly.com/question/18102056
#SPJ4
At t
1
=4.00 s, the acceleration of a particle moving at constant speed in counterclockwise circular motion is
a
1
=(10.0 m/s
2
)
i
^
+(8.00 m/s
2
)
j
^
At t
2
=7.00 s (less than one period later), the acceleration is
a
2
=(8.00 m/s
2
)
i
^
−(10.0 m/s
2
)
j
^
The period is more than 3.00 s. What is the radius of the circle?
The radius of the circle is determined as 54.3 m.
What is the radius of the circle?The radius of the circle is calculated as follows;
a = v²/r
where;
v is the linear speed of the particlea is the centripetal acceleration of the particler is the radius of the circleThe centripetal acceleration is calculated as;
a = Δv/Δt
a = (10 - 8, 8 - - 10) m/s / (7 s - 4 s)
a = (2, -18) / 3
a = (0.67, -6) m/s²
|a| = √ (0.67² + 6²)
|a| = 6.04 m/s²
The linear velocity;
v = (10 - 8, 8 - - 10) m/s
v = (2, -18) m/s
|v| = √(2² + 18²)
|v| = 18.1 m/s
The radius of the circle;
r = v²/a
r = (18.1² ) / (6.04)
r = 54.3 m
Learn more about circular motion here: https://brainly.com/question/30215891
#SPJ4
A 12.0 kg box is being pulled by two ropes as shown below. The magnitude of the tension in the right rope is 460 N. The tension magnitude in the left rope is 400 N. What is the box’s acceleration? [Let the positive direction be toward the right, and negative direction leftward]
To find the box's acceleration, we can apply Newton's second law of motion, which states that the net force acting on an object is equal to the mass of the object multiplied by its acceleration.
In this case, the net force acting on the box is the difference between the tension in the right rope and the tension in the left rope. Since the right rope is pulling to the right and the left rope is pulling to the left (opposite directions), we can write the net force equation as:
Net force = Tension in the right rope - Tension in the left rope
Net force = 460 N - 400 N
Net force = 60 N
Now we can use Newton's second law to find the acceleration:
Net force = mass × acceleration
60 N = 12.0 kg × acceleration
acceleration = 60 N / 12.0 kg
acceleration = 5.0 m/s²
Therefore, the box's acceleration is 5.0 m/s² to the right.
Learn more about acceleration here : brainly.com/question/12550364
#SPJ11
The heating coils in a hair dryer are 0.900 cm in diameter, have a combined length of 2.00 m, and a total of 750 turns. What current should flow through the coils if 975 μJ of energy is to be stored in them?
The heating coils in a hair dryer are 0.900 cm in diameter, have a combined length of 2.00 m, and a total of 750 turns. What current should flow through the coils if 975 μJ of energy is to be stored in them?
The first step to solving this problem is to use the formula for the energy stored in an inductor, which is:
E=1/2(LI^2) Where E is the energy in joules, L is the inductance in henries, and I is the current in amperes. We can rearrange this formula to solve for I as follows: I=sqrt(2E/L) We are given the diameter of the coils, which allows us to calculate the radius:
r=0.900/2
=0.450 cm
=0.00450 mL=μr^2N^2/10^6L
Where L is in henries, μ is the permeability of free space (4π x 10^-7), r is the radius of the coils, N is the number of turns, and the division by 10^6 is to convert the units from cm to meters.
Substituting the given values, we get: L=4π x 10^-7 x (0.00450 m)^2 x (750)^2 / 10^6
=0.063 Ω
We are also given the energy that is to be stored in the coils: 975 μJ.
Converting this to joules, we get: E=975 x 10^-6 J
Substituting the given values into the equation for current, we get: I=sqrt(2 x 975 x 10^-6 J / 0.063 Ω)
=0.0900 A or 90.0 mA
Therefore, a current of 90.0 mA should flow through the coils if 975 μJ of energy is to be stored in them.
To know more about heating visit:
https://brainly.com/question/13860901
#SPJ11
A train starts from rest and accelerates uniformly until it has traveled 5.6 km and acquired a velocity of 42 m/s. Then, the train moves at a constant velocity of 42 m/s for 420 s. The train then slows down uniformly at 0.065 m/s
2
until it is brought to a halt. The average acceleration of the train for the total travel is 0.39 m/s
2
0.19 m/s
2
0.13 m/s
2
0.65 m/s
2
Given data:Distance, d = 5.6 km = 5600 m Final velocity, v = 42 m/s Time taken, t = 420 s Acceleration, a = 0.065 m/s²
First, we need to find the acceleration of the train during the first part of the journey using the following formula:
v = u + at
Here,u = initial velocity
= 0
v = final velocity
= 42 m/s
t = time taken
a = acceleration of the train.Using the above formula, we get:
42 = 0 + a × tt = 42 / a
The distance traveled during this period is:
d = ut + 1/2 at²= 1/2 at²
Substituting the value of t in this equation, we get:
d = 1/2 × a × (42/a)²= 882 m
Therefore, we have the initial distance, final distance, initial velocity, and final velocity. We can use the following formula to find the average acceleration of the train during the entire journey:
v² - u² = 2as
Here,u = initial vel
= 0
v = final velocity
= 0
s = distance traveled
We need to find the value of a. The total distance traveled by the train is ocitythe sum of the distance traveled during the three periods.
Therefore, s = d₁ + d₂ + d₃ = 5600 + 882 + 0 = 6482 m
Substituting the given values, we get: 42² - 0² = 2a × 5600a = 0.39 m/s²
Therefore, the average acceleration of the train for the total travel is 0.39 m/s². Hence, option (a) is the correct answer.
To know more about Distance visit:
https://brainly.com/question/13034462
#SPJ11
Four long parallel wires carry equal currents of I=5.2 A. The figure is an end view of the conductors. The current direction is into the page at points A and B. and out of the page at points C and D. Calculate the magnitude of the magnetic field (in microTesla) at point P, located at the center of the square of edge length 0.2 m. Enter a number with 1 digit behind the decimal point.
The magnitude of the magnetic field at point P is 0.13 µT.
Current, I = 5.2 A
Length of the square = 0.2 m
We have to find out the magnetic field at point P.
We can calculate magnetic field using the below formula:
magnetic field at the center of the square = [μ₀/4π] (2I/d)
where
d is the length of the side of the square.
μ₀ = 4π×10⁻⁷ TmA⁻¹
Applying the formula:
μ₀ = 4π×10⁻⁷ TmA⁻¹I = 5.2 A
d = 0.2 m
So, magnetic field at point,
P = [4π×10⁻⁷×2×5.2]/[0.2×10⁻²]µT= 0.131×10⁻⁶ µT= 0.13 µT
Therefore, the magnitude of the magnetic field (in microTesla) at point P is 0.13 µT.
Learn more about magnetic field:
https://brainly.com/question/13160823
#SPJ11
Find the height of the tabletop above the floor. Express your answer in meters. A physics book slides off a horizontal tabletop with a speed of 2.00 m/s. It strikes the floor in 0.450 s. Ignore air resistance. For related problem-solving tips and strategies, you may want to view a Video Tutor Solution of Paintball gun. X Incorrect; Try Again; 3 attempts remaining Part B Find the horizontal distance from the edge of the table to the point where the book strikes the floor. Express your answer in meters. Part C Find the horizontal component of the book's velocity, just before the book reaches the floor. Express your answer in meters per second. Part D Find the vertical component of the book's velocity just before the book reaches the floor. Express your answer in meters per second.
Equation of motion is used to calculate the answers
To find the height of the tabletop above the floor, we can use the equation of motion for vertical motion:
h = 0.5 * g * t^2
where h is the height, g is the acceleration due to gravity (approximately 9.8 m/s^2), and t is the time of flight.
Given:
Initial velocity (u) = 0 (since the book starts from rest on the tabletop)
Final velocity (v) = ? (to be determined)
Time (t) = 0.450 s
Using the equation of motion:
v = u + g * t
v = 0 + 9.8 * 0.450
v = 4.41 m/s
Now, we can use the equation of motion for vertical motion again:
v^2 = u^2 + 2 * g * h
Plugging in the values:
(4.41)^2 = 0 + 2 * 9.8 * h
19.48 = 19.6 * h
h = 19.48 / 19.6
h = 0.9947 meters
Therefore, the height of the tabletop above the floor is approximately 0.9947 meters.
Now let's move on to Part B:
To find the horizontal distance from the edge of the table to the point where the book strikes the floor, we can use the equation of motion for horizontal motion:
d = v * t
where d is the horizontal distance, v is the horizontal component of velocity, and t is the time of flight.
Given:
Horizontal component of velocity (v) = 2.00 m/s
Time (t) = 0.450 s
Plugging in the values:
d = 2.00 * 0.450
d = 0.90 meters
Therefore, the horizontal distance from the edge of the table to the point where the book strikes the floor is 0.90 meters.
Moving on to Part C:
The horizontal component of the book's velocity remains constant throughout the motion since there is no horizontal acceleration. Therefore, just before the book reaches the floor, the horizontal component of its velocity is still 2.00 m/s.
Therefore, the horizontal component of the book's velocity just before it reaches the floor is 2.00 m/s.
Finally, for Part D:
The vertical component of the book's velocity just before it reaches the floor can be found using the equation of motion for vertical motion:
v = u + g * t
Given:
Initial velocity (u) = 0 (since the book starts from rest on the tabletop)
Time (t) = 0.450 s
Plugging in the values:
v = 0 + 9.8 * 0.450
v = 4.41 m/s
Therefore, the vertical component of the book's velocity just before it reaches the floor is 4.41 m/s.
To know more about equation of motion visit:
https://brainly.com/question/29278163
#SPJ11
An electron has an initial speed of 5.48×10
6
m/s in a uniform 4.64×10
5
N/C-strength electric fieid. The field accelierates the electron in the direction opposite to its initial velocity. (a) What is the direction of the electric field? opposite direction to the electroc's initial velocity same direction as the electron's initial velocity not enough intormation to decide (b) How far does the electron travel before coming to rest? (c) How. long does it take the electron to come to rest? (d) What is the electron's speed when it returns to its starting point? m/s
(a) The direction of the electric field is opposite to the electron's initial velocity.
(b) The electron travels approximately 6.30 meters before coming to rest.
(c) It takes approximately 11.79 seconds for the electron to come to rest.
(d) The electron's speed when it returns to its starting point is 5.48 × 10^6 m/s.
(a) The direction of the electric field is opposite to the electron's initial velocity.
(b) To determine the distance traveled by the electron before coming to rest, we can use the equation of motion for uniformly accelerated motion:
v² = u² + 2as
where:
v is the final velocity (0 m/s since the electron comes to rest),
u is the initial velocity of the electron (5.48 × 10⁶ m/s),
a is the acceleration of the electron (caused by the electric field), and
s is the distance traveled by the electron.
Rearranging the equation, we have:
s = (v² - u²) / (2a)
Substituting the given values:
v = 0 m/s
u = 5.48 × 10⁶ m/s
a = -4.64 × 10^5 N/C (negative because the acceleration is opposite to the initial velocity)
s = (0² - (5.48 × 10⁶)²) / (2 × -4.64 × 10^5)
s ≈ 6.30 m
Therefore, the electron travels approximately 6.30 meters before coming to rest.
(c) To find the time it takes for the electron to come to rest, we can use the equation of motion:
v = u + at
where:
v is the final velocity (0 m/s),
u is the initial velocity of the electron (5.48 × 10⁶ m/s),
a is the acceleration of the electron (caused by the electric field), and
t is the time.
Rearranging the equation, we have:
t = (v - u) / a
Substituting the given values:
v = 0 m/s
u = 5.48 × 10⁶ m/s
a = -4.64 × 10⁵ N/C (negative because the acceleration is opposite to the initial velocity)
t = (0 - (5.48 × 10⁶)) / (-4.64 × 10⁵)
t ≈ 11.79 s
Therefore, it takes approximately 11.79 seconds for the electron to come to rest.
(d) The speed of the electron when it returns to its starting point is equal to its initial speed, which is 5.48 × 10⁶ m/s.
Therefore, the electron's speed when it returns to its starting point is 5.48 × 10⁶ m/s.
Read more about electric field here: https://brainly.com/question/19878202
#SPJ11
A positively charged particle is held at the center of a spherical shell. The figure gives the magnitude E of the electric field versus radial distance r. The scale of the vertical axis is set by E5=14.0×107 N/C. Approximately, what is the net charge on the shell? Assume r5=4 cm.
The net charge on the shell is approximately 0.017 C.
The magnitude E of the electric field versus radial distance r graph indicates that the electric field is the strongest when the distance is at r1, which is approximately 7 cm.
Hence, if we approximate the shell's distance to be 7 cm, we can approximate the shell as a point charge at the center of the shell since the electric field's behavior within the shell does not matter.
Assuming that the shell has a net charge of Q, we can calculate the electric field's magnitude with Coulomb's Law by substituting the value of Q into the equation.
From the graph, the electric field's magnitude is E = 3.0 × 107 N/C when r = 2 cm.
E5=14.0×107 N/C is the scale of the vertical axis.
Since E5=14.0×107 N/C and E = 3.0 × 107 N/C, we can calculate that E/E5 = 3/14 = 0.2142 at r = 2 cm. Q will be equal to Q = E4πr2/ k where k is the Coulomb's constant.
Substituting the values of E, r, and k into the equation, Q can be calculated as follows:
Q = E4πr2/ k = 3.0 × 107 × 4π × (0.02)2/9.0 × 109 = 0.017 C.
This implies that the net charge on the shell is approximately 0.017 C.
For more such questions on charge, click on:
https://brainly.com/question/18102056
#SPJ8
A base ball has mass of 0.145 kg . if the pitcher threw the ball with a velocity of 37.2 m/s and the catcher’s gloves stopped the ball in 10cm . how much does force does the catcher exert on the ball ?
The formula for calculating force is Force = mass x acceleration. In this problem, we will first calculate the acceleration of the ball using the initial velocity and stopping distance.
Then we can use the calculated acceleration and the mass of the ball to find the force exerted by the catcher on the ball. Given the mass of the baseball = 0.145 kg. The velocity of the baseball = 37.2 m/s Stopping distance = 10 cm = 0.1 m Initial velocity (u) of the ball is given as 37.2 m/s.The final velocity (v) of the ball is 0 m/s since it comes to a stop. So, acceleration (a) of the ball can be calculated using the formula:v² = u² + 2aswhere v=0, u=37.2 m/s, s=0.1 ma = (v² - u²)/2sa = (0 - (37.2)²)/2 × (0.1)a = -1377.36 m/s² (The negative sign indicates that the ball is decelerating)Now, we can calculate the force exerted by the catcher using the formula: Force = mass x accelerationForce = 0.145 kg × (-1377.36 m/s²)Force = -199.42 NThe force exerted by the catcher is -199.42 N (negative sign indicates that the force is in the opposite direction to the initial motion of the ball).
Learn more about the Stopping distance:
https://brainly.com/question/24020960
#SPJ11
The somed intensity lecel is $0 dB a1 4 m away from a source. Defermune the sound intonsity level (in atB) at 12 m inkay from the sonrec.
The sound intensity level at a distance of 12 m away from the source, given that it is 0 dB at 4 m, can be determined using the inverse square law. The sound intensity level at 12 m will be -12 dB.
The sound intensity level is commonly measured in decibels (dB) and is related to the distance from the source. According to the inverse square law, the sound intensity decreases as the distance from the source increases. The inverse square law states that the sound intensity is inversely proportional to the square of the distance.
To determine the sound intensity level at 12 m, we can use the formula:
IL2 - IL1 = 10 * log10(I2 / I1)
where IL1 is the initial sound intensity level, IL2 is the final sound intensity level, I1 is the initial sound intensity, and I2 is the final sound intensity.
Given that the initial sound intensity level (IL1) is 0 dB at 4 m, we can set IL1 = 0 dB and d1 = 4 m. The final distance (d2) is given as 12 m.
Using the inverse square law, we can write:
I2 / I1 = (d1 / d2)^2
Plugging in the values, we have:
I2 / I1 = (4 m / 12 m)^2
Simplifying this, we get:
I2 / I1 = 1/9
Substituting this back into the formula for the sound intensity level, we have:
IL2 - 0 = 10 * log10(1/9)
Solving for IL2, we find IL2 ≈ -12 dB.
Therefore, the sound intensity level at a distance of 12 m away from the source, given that it is 0 dB at 4 m, is approximately -12 dB.
learn more about sound intensity here:
https://brainly.com/question/32194259
#SPJ11
A steam catapult launches a jet aircraft from the aircraft carrier John C. Stennis, giving it a speed of 185mi/h in 2.60 s : (a) Find the average acceleration of the plane. mn
2
(b) Assuming the acceleration is constant, find the distance the plane moves. m
The average acceleration of the plane is approximately 79.52 m/s².
The distance the plane moves, assuming constant acceleration, is approximately 270.30 meters.
(a) To find the average acceleration of the plane, we use the formula:
Average acceleration = Change in velocity / Time
Given that the initial velocity (u) is 0 mph (since the plane starts from rest), the final velocity (v) is 185 mph, and the time (t) is 2.60 seconds, we can calculate the average acceleration:
Average acceleration = (v - u) / t
Average acceleration = (185 mph - 0 mph) / 2.60 s
Converting mph to m/s (1 mph = 0.44704 m/s):
Average acceleration = (185 mph * 0.44704 m/s - 0 mph) / 2.60 s
Average acceleration ≈ 79.52 m/s²
Therefore, the average acceleration of the plane is approximately 79.52 m/s².
(b) Assuming the acceleration is constant, we can use the kinematic equation:
Distance = Initial velocity * Time + (1/2) * Acceleration * Time²
Given that the initial velocity (u) is 0 mph, the time (t) is 2.60 seconds, and the average acceleration is 79.52 m/s², we can calculate the distance:
Distance = 0 mph * 2.60 s + (1/2) * 79.52 m/s² * (2.60 s)²
Converting mph to m/s:
Distance = 0 m/s * 2.60 s + (1/2) * 79.52 m/s² * (2.60 s)²
Distance ≈ 270.30 meters
Therefore, the distance the plane moves, assuming constant acceleration, is approximately 270.30 meters.
To know more about Distance, visit:
https://brainly.com/question/33573730
#SPJ11
