Answer:
1.74×10⁻³ m
Explanation:
Applying,
ε = Stress/strain............. Equation 1
Where ε = Young's modulus
But,
Stress = F/A.............. Equation 2
Where F = Force, A = Area
Strain = e/L.............. Equation 3
e = extension, L = Length.
Substitute equation 2 and 3 into equation 1
ε = (F/A)/(e/L) = FL/eA............. Equation 4
From the question,
Given: F = 285 N, L = 29 cm = 0.29 m, ε = 5.00×10⁹ N/m²,
A = πd²/4 = 3.14(0.0011²)/4 = 9.4985×10⁻⁶ m²
Substitute these values into equation 4
5.00×10⁹ = (285×0.29)/(9.4985×10⁻⁶×e)
Solve for e
e = (285×0.29)/(5.00×10⁹×9.4985×10⁻⁶)
e = 82.65/4.74925×10⁴
e = 1.74×10⁻³ m
A space ship has four thrusters positioned on the top and bottom, and left and right as shown below. The thrusters can be operated independently or together to help the ship navigate in all directions.
Initially, the Space Probe is floating towards the East, as shown below, with a velocity, v. The pilot then turns on thruster #2.
Select one:
a.
Space ship will have a velocity to the West and will be speeding up.
b.
Space ship will have a velocity to the East and will be speeding up.
c.
Space ship will have a velocity to the East and will be slowing down.
d.
Space ship will have a velocity to the West and will be slowing down.
e.
Ship experiences no change in motion.
Answer:
The correct answer is - c. Spaceship will have a velocity to the East and will be slowing down.
Explanation:
In this case, if turned on thruster #2 then it will exert force on the west side as thruster 2 is on the east side and it can be understood by Newton's third law that says each action has the same but opposite reaction.
As the spaceship engine applies force on the east side then according to the law the exhauster gas applies on towards west direction. It will try to decrease the velocity of the spaceship however, the direction of floating still be east side initally.
A block of mass 0.260 kg is placed on top of a light, vertical spring of force constant 5 200 N/m and pushed downward so that the spring is compressed by 0.090 m. After the block is released from rest, it travels upward and then leaves the spring. To what maximum height above the point of release does it rise
After being released, the restoring force exerted by the spring performs
1/2 (5200 N/m) (0.090 m)² = 12.06 J
of work on the block. At the same time, the block's weight performs
- (0.260 kg) g (0.090 m) ≈ -0.229 J
of work. Then the total work done on the block is about
W ≈ 11.83 J
The block accelerates to a speed v such that, by the work-energy theorem,
W = ∆K ==> 11.83 J = 1/2 (0.260 kg) v ² ==> v ≈ 9.54 m/s
Past the equilibrium point, the spring no longer exerts a force on the block, and the only force acting on it is due to its weight, hence it has a downward acceleration of magnitude g. At its highest point, the block has zero velocity, so that
0² - v ² = -2gy
where y is the maximum height. Solving for y gives
y = v ²/(2g) ≈ 4.64 m
Determine the acceleration of a pendulum bob as it passes through an angle of 15 degrees to the right of the equilibrium point.
Answer:
Explanation:
Since energy is conserved:
2
mu
2
=
2
mv
2
+mgh
⇒u
2
=v
2
+2gh
⇒(3)
2
=v
2
+2(9.8)(0.5−0.5cos60)
⇒v=2m/s
Acceleration of the simple pendulum is 2.62 m/s².
What is meant by a simple pendulum ?When a point mass is suspended from a fixed support by a light, non-extensible string, the instrument is said to be a simple pendulum.
Here,
Let the mass of the bob be m. The simple pendulum is attached to the fixed support with a string having length l. The pendulum makes an angle of 15° with the vertical from the equilibrium point.
Let T be the tension acting on the string.
As, the bob passes through the angle,
The weight of the bob becomes equal to the vertical component of the tension.
mg = T cos15°
Also, the horizontal component of the tension,
T sin15° = ma
By solving these two equations, we get that,
Acceleration of the simple pendulum,
a = g tan15°
a = 9.8 x 0.267
a = 2.62 m/s²
Hence,
Acceleration of the simple pendulum is 2.62 m/s².
To learn more about simple pendulum, click:
https://brainly.com/question/31816771
#SPJ3
A physical pendulum in the form of a planar object moves in simple harmonic motion with a frequency of 0.680 Hz. The pendulum has a mass of 2.00 kg, and the pivot is located 0.340 m from the center of mass. Determine the moment of inertia of the pendulum about the pivot point.
Answer:
Therefore, the moment of inertia is:
[tex]I=0.37 \: kgm^{2} [/tex]
Explanation:
The period of an oscillation equation of a solid pendulum is given by:
[tex]T=2\pi \sqrt{\frac{I}{Mgd}}[/tex] (1)
Where:
I is the moment of inertiaM is the mass of the pendulumd is the distance from the center of mass to the pivotg is the gravityLet's solve the equation (1) for I
[tex]T=2\pi \sqrt{\frac{I}{Mgd}}[/tex]
[tex]I=Mgd(\frac{T}{2\pi})^{2}[/tex]
Before find I, we need to remember that
[tex]T = \frac{1}{f}=\frac{1}{0.680}=1.47\: s[/tex]
Now, the moment of inertia will be:
[tex]I=2*9.81*0.340(\frac{1.47}{2\pi})^{2}[/tex]
Therefore, the moment of inertia is:
[tex]I=0.37 \: kgm^{2} [/tex]
I hope it helps you!
The current in resistor Y is..?
(A)
Explanation:
We can see that the resistors are connected in parallel so all of them have the same voltage of 100 V. We also know that
[tex]P = VI[/tex]
Since resistor Y dissipates 100 W of power, we can solve for the current as
[tex]I = \dfrac{P}{V} = \dfrac{100\:\text{W}}{100\:\text{V}} = 1.0\:\text{A}[/tex]
The current in resistor Y is
a)1.0 ADifference between uniform motion and non uniform motion
Answer:
When an object covers equal distance in an equal interval of time, it is uniform motion but when an object covers unequal distance in an equal interval of time, it is called non uniform motion.
A visible violet light emits light with a wavelength of 4.00 × 10-7 m.
Calculate the frequency of the violet light.
A)6.30 × 10 -1 Hz
B)7.50 × 10 14 Hz
C)6.30 × 10 24 Hz
D)7.50 × 10 1 Hz
Answer:
The correct option is B. 7.5 * 10¹⁴ Hz
Explanation:
Frequency = (speed) / (wavelength)
= (3 x 10⁸ m/s) / (4 x 10⁻⁷ m)
= (3/4 x 10¹⁵) ( m / m - s )
= (0.75 x 10¹⁵) /sec
= 7.5 x 10¹⁴ Hz
= 750,000 GHz
Answer:
Mark Brainliest please
answer is
Explanation:
For any wave,
Frequency = (speed) / (wavelength)
= (3 x 10⁸ m/s) / (4 x 10⁻⁷ m)
= (3/4 x 10¹⁵) ( m / m - s )
= (0.75 x 10¹⁵) /sec
= 7.5 x 10¹⁴ Hz
= 750,000 GH
Determine the density in kg \cm of solid whose Made is 1080 and whose dimension in cm are length=3 ,width=4,and height=3
Answer:
d = 30kg/cm³
Explanation:
d = m/v
d = 1080kg/(3cm*4cm*3cm)
d = 30kg/cm³
Cho hệ thống thùng lắc có mô hình tại vị trí đang xét như hình vẽ
Answer:
I can't understand this language!!!Answer:
vdhdbdnnsnsbdhhshzbhshsbbsbd is not ask you to be able and r in the exam qq and
Consider two closely spaced and oppositely charged parallel metal plates. The plates are square with sides of length L and carry charges Q and -Q on their facing surfaces. What is the magnitude of the electric field in the region between the plates
Answer:
E_ {total} = [tex]\frac{Q }{L^2 \epsilon_o}[/tex]
Explanation:
In this exercise you are asked to calculate the electric field between two plates, the electric field is a vector
E_ {total} = E₁ + E₂
E_ {total} = 2 E
where E₁ and E₂ are the fields of each plate, we have used that for the positively charged plate the field is outgoing and for the negatively charged plate the field is incoming, therefore in the space between the plates for a test charge the two fields point in the same direction
to calculate the field created by a plate let's use Gauss's law
Ф = ∫ E . dA = q_{int} /ε₀
As a Gaussian surface we use a cylinder with the base parallel to the plate, therefore the direction of the electric field and the normal to the surface are parallel, therefore the scalar product is reduced to the algebraic product.
E 2A = q_{int} / ε₀
where the 2 is due to the surface has two faces
indicate that the surface has a uniform charge for which we can define a surface density
σ = q_{int} / A
q_{int} = σ A
we substitute
E 2A = σ A /ε₀
E = σ / 2ε₀
therefore the total field is
E_ {total} = σ /ε₀
let's substitute the density for the charge of the whole plate
σ= Q / L²
E_ {total} = [tex]\frac{Q }{L^2 \epsilon_o}[/tex]
Is it true that as we gain mass the force of gravity on us decreases
Answer:
No. As we gain mass the force of gravity on us does not decrease
Choose one. 5 points
Use the equation from week 3:
frequency =
wavespeed
wavelength
and the wavelength you found in #3 to calculate the frequency of this photon (remember the speed of
light is 3E8 m/s);
7.6E14 Hz
6.0E14 Hz
4,6E14 Hz
The frequency is 4,6E14 Hz.
What is the frequency?
Frequency is the fee at which modern changes direction in step with 2nd. it's far measured in hertz (Hz), a worldwide unit of degree wherein 1 hertz is identical to 1 cycle in line with 2d. Hertz (Hz) = One hertz is the same as 1 cycle in step with the second. Cycle = One entire wave of alternating present-day voltage.
Frequency describes the number of waves that pass a hard and fast place in a given quantity of time. So if the time it takes for a wave to skip is half of 2d, the frequency is 2 per 2nd. If it takes 1/one hundred of an hour, the frequency is a hundred in step with hour.
Learn more about frequency here:-https://brainly.com/question/254161
#SPJ2
Where is the center of mass of homogeneous body which has a regular
Following the definition of the center of mass, "In physics, the center of mass of a distribution of mass in space is the unique point where the weighted relative position of the distributed mass sums to zero."
(see explanation below)
calculate the length of wire.
Answer:
L = 169.5 m
Explanation:
Using Ohm's Law:
V = IR
where,
V = Voltage = 1.5 V
I = Current = 10 mA = 0.01 A
R = Resistance = ?
Therefore,
1.5 V = (0.01 A)R
R = 150 Ω
But the resistance of a wire is given by the following formula:
[tex]R = \frac{\rho L}{A}[/tex]
where,
ρ = resistivity = 1 x 10⁻⁶ Ω.m
L = length of wire = ?
A = cross-sectional area of wire = πr² = π(0.6 mm)² = π(0.6 x 10⁻³ m)²
A = 1.13 x 10⁻⁶ m²
Therefore,
[tex]150\ \Omega = \frac{(1\ x\ 10^{-6}\ \Omega .m)L}{1.13\ x\ 10^{-6}\ m^2}\\\\L = \frac{150\ \Omega(1.13\ x\ 10^{-6}\ m^2)}{1\ x\ 10^{-6}\ \Omega .m}\\\\[/tex]
L = 169.5 m
Which of the following is a form of mechanical energy?
A. Chemical energy
B. Gravitational potential energy
C. Thermal energy
D. Nuclear energy
Answer:
B
Explanation:
no reason for this answer
Is there any absolute rest or motion? Describe the types of motion with one example of each type
Michelson and Morley concluded from the results of their experiment that Group of answer choices the experiment was successful in not detecting a shift in the interference pattern. the experiment was a failure since they detected a shift in the interference pattern. the experiment was a failure since there was no detectable shift in the interference pattern. the experiment was successful in detecting a shift in the interference pattern.
Answer:
The results of the experiment indicated a shift consistent with zero, and certainly less than a twentieth of the shift expected if the Earth's velocity in orbit around the sun was the same as its velocity through the ether.
Explanation:
It was recorded that the temperature of a body was 320 degree F determine the value of the temperature in kelvin
Answer:
433.15K
Explanation:
(320°F − 32) × 5/9 + 273.15 = 433.15K
Partial tides _______. Question 7 options: represent various components of local tides that are resolved mathematically are predicted individually are added together to predict the height and timing of astronomical tides All of the above are correct. Only a and c are correct.
Complete Question
Partial tides __________.
Question 7 options:
a. represent various components of local tides that are resolved mathematically
b. are added together to predict the height and timing of astronomical tides
c. consist of 4 components due to the influence of celestial bodies
d. consist of up to 60 components due to astronomical and non-astronomical factors
e. All of the above except c are correct.
Answer:
Option E
Explanation:
Generally
Partial tides represent various components of local tides that are resolved mathematically
Partial tides are added together to predict the height and timing of astronomical tides
Partial tides consist of up to 60 components due to astronomical and non-astronomical factors
But Partial tides do not consist of 4 components due to the influence of celestial bodies
Therefore
All of the above except c are correct.
Option E
A smokestack of height H = 50 m emits a pollutant in a 3 m/s wind. The plume is carried downwind by advection (wind speed U = 3 m/s) and is simultaneously dispersing vertically with a turbulent diffusion coefficient D. The vertical diffusion causes the plume to widen vertically over time, with halfâwidth (distance from centerline to edge) increasing as:
half width = 2 â2Dt
The plume reaches the ground some distance L downwind of the base of the smokestack (see sketch in book on page 203)
a. If L = 2 km, estimate the value of the turbulent diffusion coefficient D.
b. Under the same wind speed and turbulence conditions, what would be the value of L if the smokestack were twice as high?
Answer:
a) 0.46875
b) 8 km
Explanation:
Smokestack height ( H ) = 50 m
speed of pollutant / wind speed = 3 m/s
Half width = 2 [tex]\sqrt{2Dt }[/tex] = 50 m ---- ( 1 )
a) If L = 2 km
value of turbulent diffusion coefficient D
back to equation 1
50 = 2 √ 2 * D * ( 2000/3 )
2500 = 4 * 2 * D * ( 2000/3 )
D = 2500 / ( 8 * ( 2000/3 ) )
= 0.46875
where : time to travel ( t ) = Distance / speed = 2000 / 3
b) when the smoke stack = 50 * 2 = 100 m
L = 800 m = 8 km
attached below is the detailed solution
A 2kg ball is rolled along the floor for 0.8 m at a constant speed of 6 m/s. What is the work done by gravity?
A, 0
B, 16 J
C, 72 J
D, 450 J
E, 90 J
=F×s×cosa=2×g×0,8×cos90°= 0
The work done by gravity on a ball of 2 kg which is moving with a constant speed of 6 meter per second is zero. Thus, the correct option is A.
What is Work?Work is the energy transfer to or from an object through the application of force along with the displacement. For a constant force aligned with the direction of motion, the work done is equal to the product of the force strength which is applied and the distance traveled by the object.
Work = Force × Displacement
Force = Mass × Acceleration
Acceleration of the ball is zero as it is moving with a constant speed. Therefore, the work done by the gravity is zero.
Therefore, the correct option is A.
Learn more about Work done here:
https://brainly.com/question/13662169
#SPJ2
11. From this lab we can conclude that a) the heat transferred when objects are rubbed together creates an energy that can cause objects to move towards or away from each other. b) objects such as balloons and sweaters have a natural affinity towards each other. They will attract each other whether they are rubbed together or not. c) charges exert forces on other charges. do) charges do not exert forces on other charges.
Answer:
c) charges exert forces on other charges.
Explanation:
When two different materials are rubbed together, there is a transfer of electrons from one material to the other material so this causes one object to become positively charged and the other object is negatively charged so they will attract each other not repel each other. Charges exert forces on other charges i.e. opposite charges attract each other whereas similar charges repel each other so in both cases force are exerted on one another.
A person runs up the stairs elevating his 102 kg body a vertical distance of 2.29 meters in a time of 1.32 seconds at a constant speed.
Determine the work done by the person climbing the stair case.
Answer:
Work done = 2289.084 Joules
Explanation:
Given the following data;
Mass = 102 Kg
Height = 2.29
Time = 1.32 seconds
We know that acceleration due to gravity, g = 9.8 m/s²
a. To find the work done by the person;
Here, work would be done in the form of gravitational potential energy.
Gravitational potential energy (GPE) is an energy possessed by an object or body due to its position above the earth.
Mathematically, gravitational potential energy is given by the formula;
G.P.E = mgh
Where;
G.P.E represents potential energy measured in Joules.
m represents the mass of an object.
g represents acceleration due to gravity measured in meters per seconds square.
h represents the height measured in meters.
Substituting into the formula, we have;
Work done = 102 * 2.29 * 9.8
Work done = 2289.084 Joules
Total Internal Reflection: A ray of light in glass strikes a water-glass interface at an angle of incidence equal to one-half the critical angle for that interface. The index of refraction for water is 1.33, and for the glass it is 1.43. What angle does the refracted ray in the water make with the normal
Answer:
θ₄ = 37.2º
Explanation:
For this exercise it must be solved in two parts, the first part we look for the critical angle, for this we use the law of refraction with the angle in the middle of transmission of tea = 90º
n₁ sin θ₁= n₂ sin 90
θ₁ = sin⁻¹ [tex]\frac{n_2}{n_1}[/tex]
θ₁ = sin⁻¹ (1.33 / 1.43)
θ₁ = 68.4º
They indicate that the angle of incidence is half of the critical angle
θ₃ = 68.4 / 2 = 34.2º
Let's use the law of refraction again
n₁ sin θ₃ = n₂ sin θ₄
sin θ₄ = [tex]\frac{n_1}{n_2}[/tex] sin θ₃
sin θ₄ = [tex]\frac{1.43}{1.33}[/tex] sin 34.2
θ₄ = sin⁻¹ 0.604345
θ₄ = 37.2º
Two divers, G and H, are at depths 20 m and 40 m respectively
below the water surface in lake. The pressure on G is P, while
the pressure on H is P2 if the atmospheric pressure is equivalent
to 10 m of water, then the value of P2/P1 is.
A. 1.67.
B. 2.00.
C. 0.50.
D. 0.60.
Answer:
B
Explanation:
P1/P1 = 40/20
=2
A friend lends you the eyepiece of his microscope to use on your own microscope. He claims that since his eyepiece has the same diameter as yours but twice the focal length, the resolving power of your microscope will be doubled. Is his claim valid? Explain.
Answer:
The resolving power remains same.
Explanation:
The resolving power of the lens is directly proportional to the diameter of the lens not on the focal length.
As the diameter is same but the focal length is doubled so the resolving power remains same.
1 A thing ring has a mass of 6kg and a radius of 20cm. calculate the rotational inertia.
Answer:
2400kgm²
Explanation:
Rotational inertia=mass x radius²
Which of the following is not true about Triton, the large moon of Neptune? It is more reflective than Earth's Moon. It is larger than Earth's Moon. It is in a retrograde orbit. It has a thin atmosphere. It has nitrogen geysers.
Answer:
Triton is the largest of Neptune's 13 moons. It is unusual because it is the only large moon in our solar system that orbits in the opposite direction of its planet's rotation―a retrograde orbit. ... Like our own moon, Triton is locked in synchronous rotation with Neptune―one side faces the planet at all times.
5. A bicyclist is finishing her repair of a flat tire when a friend rides by at a constant velocity of
3.5 m/s. Three seconds later, the bicyclist hops on her bike and accelerates at 3.6 m/s² until she
catches her friend.
a. How much time does it take until she catches her friend?
b. How far has she traveled in this time?
c. What is her speed when she catches up?
Answer:
a) t = 3.6 s
b) d = 23 m
c) v = 13 m/s
Explanation:
Let t be the time the accelerating rider rides
the distance she travels is
d = ½3.6t²
the distance for the other cyclist is
d =3.5(t + 3)
½3.6t² = 3.5(t + 3)
1.8t² - 3.5t - 10.5 = 0
quadratic formula, positive answer
t = (3.5 + √(3.5² - 4(1.8)(-10.5))) / (2(1.8))
t = 3.575786...
d = ½(3.6)(3.575786²) = 23.015...
v = 3.6(3.575786) = 12.8728...
Explain how newton's first law of motion follows from second law?
Answer:
Newton's First Law of Motion states that a body will stay at rest or continue its path with constant velocity unless an external force acts upon it. Newton's Second Law of Motion states that the net force that acts upon a body is equal to the mass of the body multiplied by the acceleration due to the net force.
