[tex]\\ \rm\longmapsto a=\dfrac{v-u}{t}[/tex]
[tex]\\ \rm\longmapsto a=\dfrac{12.6-9.5}{12}[/tex]
[tex]\\ \rm\longmapsto a=\dfrac{3.1}{12}[/tex]
[tex]\\ \rm\longmapsto \overrightarrow{a}=0.25m/s^2[/tex]
A sports car accelerates uniformly from rest to 24 m/s in 6 seconds. Calculate the acceleration of the car
Answer:
a = 4m/s^2
Explanation:
Velocity(V) = uniform = 24m/s
time(t) = 6sec
Acceleration(a) = V/t
= 24/6
= 4m/s^2
When a sports car accelerates uniformly from rest to 24 m/s in 6 seconds,then acceleration of the car would be 4 m/s²
What are the three equations of motion?There are three equations of motion given by Newton
The first equation is given as follows
v = u + at
the second equation is given as follows
S = ut + 1/2×a×t²
the third equation is given as follows
v² - u² = 2×a×s
Note that these equations are only valid for a uniform acceleration.
As given problem sport car accelerates uniformly from rest to 24 m/s in 6 seconds then the acceleration of the car can be calculated by using the first equation of motion
v = u + at
As given the initial velocity u= 0
The final velocity v = 24 m/s
The time taken is t= 6 seconds
By substituting the respective values of velocity and time
24 = 0+ a*6
a = 24/6
a = 4 m/s²
Thus, when a sports car accelerates uniformly from rest to 24 m/s in 6 seconds,then acceleration of the car comes out to be 4 m/s²
Learn more about equations of motion from here
brainly.com/question/5955789
#SPJ2
Polarized sunglasses:
a. block most sunlight because sunlight is polarized
b. are better but work the same way as non-polarized sunglasses
c. are polarized to filter out certain wavelengths of light
d. block reflected light because reflected light is partially polarized.
Polarized sunglasses creates filter of vertical openings for light. The light rays will reach the eyes of human vertically only.
The sun rays will not reach human eye directly which will create a shield for sun light burden on human eye.
Polarized sunglasses are best used for blocking and eliminating certain wavelengths of light.
Therefore the correct answer is option C. Polarizes Sunglasses are polarized and it filter out certain wavelengths of light.
Learn more at https://brainly.com/question/24372632
Which of the following accurately describes circuits?
options:
A)
In a parallel circuit, there's only one path for the current to travel.
B)
In a series circuit, the amount of current passing through each part of the circuit may vary.
C)
In a series circuit, the current can flow through only one path from start to finish.
D)
In a parallel circuit, the same amount of current flows through each part of the circuit.
' C ' is the only correct statement.
what is the value of Pi
Answer:
the value of pi is approximately 3.14
Explanation:
or pi = approx 3.14159265358979324...
Transistor circuits are sometimes referred to as switching circuits - Why is this?
Explanation:
One of the most common uses for transistors in an electronic circuit is as simple switches. In short, a transistor conducts current across the collector-emitter path only when a voltage is applied to the base. When no base voltage is present, the switch is off. When base voltage is present, the switch is on.
Fish is cold blooded animal
Solar System - Scaling. When you look at Neptune in a telescope, you are actually looking into the past as the light has to travel from Neptune to your eyes. If the speed of light is ~300,000 km/s, how far back into the past are you looking (or put another way, how long does it take light to travel from Neptune to your eyes on Earth)
Answer:
Distance from sun to Neptune = 4.495E9 km
Time for light to travel = 4.495E9 / 3E5 sec = 14,980 sec
That is from sun to Neptune time fof light = 250 min
Time for light to travel from sun to earth is about 8 min
So the time from Neptune would be 242 to 258 min depending on position of Neptune - Note that Neptune is about 30X as far from the sun as earth and
250 min / 8 min is roughly 30
The uniform motion of kinematics allows us to find the time it takes for light to arrive from Neptune to Earth, which varies between:
t₁ = 1.45 10⁴ s and t₂₂= 1.55 10⁴ s
depending on the relative distance of the two planets
given parameters
The speed of light c = 300,000 km / s = 3 10⁸ m / s The distance from Neptune to Sum
to find
The time when light arrives from Neptune to Earth
They velocit of an electromagnetic wave is constant, so we can use the uniform motion relationships
v = d / t
t = d / v
where v is the speed of light, d the distance and y time, in this case the speed of the wave is the speed of light (v = c)
We look in the tables for the distances and the rotation periods around the sun
distance ( m) period (s)
Sun Neptunium 4.50 10¹² 5.2 10⁹
Sun - Earth 1.5 10¹¹ 3.2 10⁷
With the data of the period it is observed that the rotation of Neptune is much greater than that of Eart rotation around the sun, for which we will assume that Neptunium is fixed in space and the Earth may be in its aphelion or perihelion, maximum approach o away distance from the sun, consequently we calculate the time for the two cases:
Maximum approach
positions relative distance from the dos Plantetas is
Δd = [tex]x_{Neptuno - Sum} - x_{Earth - Sum}[/tex]d
Δd = 4.50 10¹² - 1.5 10¹¹
Δd = 43.5 10¹¹ m
the time it takes for Neptune's light to reach Earth is
Δt = [tex]\frac{ 43.5 \ 10^{11} }{3 \ 10^8}[/tex]
Δt = 14.5 10³ s
Δt = 1.45 10⁴ s
We reduce to hours
Δt = 1.45 10⁴ s (1 h / 3600 s) = 4.03 h
Maximum away
Δd = [tex]x_{Neptune - Sum} + x_{Neptune-Sum}[/tex]
Δd = 4.50 10¹² + 1.5 10¹¹
Δd = 46.5 10¹¹
The time is
Δt = [tex]\frac{46.5 \ 10^{11}}{ 3 \ 10^8}[/tex]
Δt = 15.5 10³
Δt = 1.55 10⁴ s
We reduce to hours
Δt = 1.55 10⁴ s (1 h / 3600 s) = 4.31 h
In conclusion, the time it takes for light to arrive from Neptune to Earth varies between:
t₁ = 1.45 10⁴ s and t₂ = 1.55 10⁴ s
depending on the relative distance of the two plants
learn more about the speed of light here: https://brainly.com/question/14355103
You are outdoors when you hear the constant chirp of a still cricket. You start walking toward the cricket and at some point you are able to detect that the intensity of the chirp of the cricket has increased by a factor of 4. What of the following statements is true at your new position with respect to the cricket?
a. The power delivered by the sound wave you hear has doubled.
b. The speed of the sound wave emitted by the cricket has decreased by a factor of 4.
c. The distance between you and the cricket has decreased by a factor of 2
Answer:
C
Explanation:
intensity = Power delivered by the sound (Watt)/ Surounding Area (m²)
I = P/A
A = πr²
r = is the distance between you and the cricket.
so in other form we can get
I = P/πr²
let take I(1) as first intensitilynyou heard and I(2) as the increased intensity.
I(1) / I(2) = r(2)² / r(1)²
1/4 = r(2)²/r(1)²
1/2 = r(2) / r(1)
r(2) = ½ r(1)
or r(2) is decreaases by a factor of 2.
Define wave length as applied to wave motion
Answer: Wavelength can be defined as the distance between two successive crests or troughs of a wave. It is measured in the direction of the wave.
Explanation:
Wavelength refers to the length or distance between two identical points of neighboring cycles of a wave signal traveling in space or in any physical medium. ... The wavelength of a signal is inversely proportional to its frequency, that is, the higher the frequency, the shorter the wavelength.
two thin lenses with the focal length of magnitude 15.0 cm . the first is diverging and second is converging lens are located 11.3 cm apart. an object 1.60 mm tall is placed 25 cm to the left of the first diverging lens. how far the first lens is the final image is formed?
is the final image is real or virtual?
what is the height of image?
Answer:
grandson annual Iranian Jamal Jamal Hannah travel
A mass is hanging from the end of a horizontal bar that pivots around an axis through its center, but it is being held stationary. The bar is then released and begins to rotate. As the bar rotates from horizontal to vertical, the magnitude of the torque on the bar: ________
Answer:
The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.
The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.
What is the difference between atomic number and atomic mass ?Atomic number of an element is defined as total number of protons present in the nucleus, neutrons carry no net electrical charge, so it is the charge number of the nucleus.
atomic mass of an element can be defined as the atomic weight is measured total mass of an element’s atom, the total number of neutrons and protons in the nucleus of an atom.
Both Atomic mass and an atomic number of elements are closely related if atomic number is high, then the atomic mass is also said to be high.
For more details regarding fire mass , visit
brainly.com/question/16858932
#SPJ2
Calcular la longitud del faldón de una Rampa de Acceso , que en planta tiene una longitud de 20 m y la pendiente es 27%.
La longitud del faldón de la rampa es de 5.4 m.
La pendiente expresada en porcentaje sigue la siguiente ecuación:
[tex]m=\frac{y}{x}*100[/tex] (1)
Donde:
y es la elevacion de la rampa (faldón)x es la longitud de la ramapa (20 m)Sabemos que la pendiente es de 27%. Por lo tanto, usando la ecuación 1, despejamos y.
[tex]27=\frac{y}{20}*100[/tex]
[tex]y=\frac{27*20}{100}[/tex]
[tex]y=5.4\: m[/tex]
La longitud del faldón es 5.4 m
Pudes ver más sobre el tema aquí:
https://brainly.com/question/8906330
Light of a given wavelength is used to illuminate the surface of a metal, however, no photoelectrons are emitted. In order to cause electrons to be ejected from the surface of this metal you should: ___________
a. use light of the same wavelength but increase its intensity.
b. use light of a shorter wavelength.
c. use light of the same wavelength but decrease its intensity.
d. use light of a longer wavelength.
Answer:
use light of the same wavelength but decrease it's intensity
Can someone please help!!!
Answer:
W = F • ∆x
so for work to be done, a force and displacement has to be in the same direction. (Ex: a box is being pushed forward and it's also moving forward.)
A projectile is launched with speed of 128 m/s, at an angle of 60° with the horizontal. After 2.0 s, what is the vertical component of the projectile's velocity?
After 2.0s, what is the speed of the projectile?
Answer:
a) 91 m/s
b) 111 m/s
Explanation:
v = u + at
v = 128sin60 + (-9.8)(2.0) = 91.25125... m/s
v = √(vx² + vy²) = √((128cos60)² + 91.25125²) = 111.4575... m/s
Two different galvanometers G1 and G2, have internal resistances r1and r2. The galvanometers G1 and G2 require the same current IC1=IC2 for a full-scale deflection of their pointers. These galvanometers G1 and G2 are used to build lab-made ammeters A1 and A2 . Both ammeters A1 and A2 have the same maximum scale reading Imax1=Imax2=Imax. To build A1 ,shunt resistor of resistance Rsh1is used and to build A2 , shunt resistor of resistance Rsh2 is used. The value of these shunt resistor resistances are such that: Rsh1=3Rsh2. What is the ratio oftheir internal resistances: r1:r2?
Answer:
there are 3 photos attached. so check
Explanation:
M
A boy of mass 60 kg and a girl of mass 40 kg are
together and at rest on a frozen pond and push
each other apart. The girl moves in a negative
direction with a speed of 3 m/s. What must be the
total final momentum of the boy AND girl
combined?
A. -120 kgm/s
B. 0 kgm/s
C. -100 kgm/s
D. 120 kgm/s
Answer:
option D thinking so
Explanation:
okay na your whish
An object starts from rest with constant acceleration of 8m/s2
along a straight line. Find The distance travelled during the 5th second.
Using second equation of kinematics
[tex]\boxed{\sf s=ut+\dfrac{1}{2}at^2}[/tex]
[tex]\\ \qquad\quad\sf{:}\dashrightarrow s=0(5)+\dfrac{1}{2}(8)(5)^2[/tex]
[tex]\\ \qquad\quad\sf{:}\dashrightarrow s=4(25)[/tex]
[tex]\\ \qquad\quad\sf{:}\dashrightarrow s=100m[/tex]
You spaceship has a snazzy lounge called Ten-Forward that needs a new spacecouch. Sadly the couch you bought is too long and won't fit into your car when it is stationary. The couch has a length Lc = 14.0 m and mass m = 49 kg, and your shuttlecraft has a length of L = 9.0 m How fast would you need to run, in terms of the speed of light c, in order to get the couch to fit inside the length of the shuttlecraft?
Answer:
v = speed
c = speed of light
using the equation
L = Lc Sqrt( 1 - (v/c)2)
9 = 14 Sqrt( 1 - (v/c)2)
v/c = 0.765
v = 0.765 c
Infrared and ultraviolet waves have different frequencies.
Both types of wave can have harmful effects on human beings.
Describe the harmful effects of infrared and ultraviolet waves, relating them to the frequencies of the waves.
Answer:
For infrared and ultraviolet waves have different frequencies. Both types of wave can have harmful effects on human beings. Describe the harmful effects of infrared and ultraviolet waves, relating them to the frequencies of the waves. Medical studies indicate that prolonged IR exposure can lead to lens, cornea and retina damage, including cataracts, corneal ulcers and retinal burns, respectively. To help protect against long-term IR exposure, workers can wear products with IR filters or reflective coatings.When you look at the EM spectrum, UV waves are quite a bit smaller in wavelength than infrared, and x-rays/gamma rays are even smaller. Therefore, UV waves are probably causing more harm than infrared waves, and x-rays/gamma rays are probably doing even more damage.
Thank You
Please mark me Brainliest
Infrared and ultraviolet waves have different frequencies. Infrared waves have lower frequencies and longer wavelengths, while ultraviolet waves have higher frequencies and shorter wavelengths.
Harmful effects of Infrared waves:
Infrared waves have lower frequencies and are often associated with heat radiation. Prolonged exposure to intense infrared radiation can lead to thermal burns and damage to the skin and eyes. Infrared radiation can also cause dehydration and overheating of the body, especially in hot environments. While infrared radiation is not as harmful as ultraviolet radiation, excessive exposure can still lead to health issues.
Harmful effects of Ultraviolet waves:
Ultraviolet waves have higher frequencies and shorter wavelengths, making them more energetic than infrared waves. UV radiation from the sun is a well-known harmful agent. Short-term exposure to intense UV radiation can cause sunburn, skin redness, and eye irritation. Long-term exposure to UV radiation can lead to more serious health problems such as skin aging, cataracts, and an increased risk of skin cancer. UV radiation can also damage DNA in skin cells, leading to mutations and potential carcinogenesis.
It is essential to protect ourselves from both infrared and ultraviolet waves to prevent harmful effects. Using sunscreen and wearing protective clothing can help shield the skin from UV radiation. Limiting exposure to intense sources of infrared radiation, such as hot objects or infrared heaters, can help reduce the risk of thermal burns and overheating. Understanding the differences in the frequencies of these waves allows us to implement appropriate safety measures and protect our health.
To learn more about Infrared and ultraviolet waves, here
https://brainly.com/question/3091095
#SPJ2
Which of the following choices is not an example of climate?
0000
San Diego has mild, warm temperatures and sea breezes year-round.
Anchorage has short, cool summers and long, snowy winters.
It will be 78° on Friday in Clovis.
Florida is tropical, with a significant rainy season.
Answer:
Florida is tropical, with a significant rainy seson
Why are scientific models important?
Answer:
Scientific models are representations of objects, systems or events and are used as tools for understanding the natural world. Models use familiar objects to represent unfamiliar things. Models can help scientists communicate their ideas, understand processes, and make predictions.
the specific heat capacity of a substance is 500J/kg/oC. Find the heat required to rise the temperature of 10 quintial of the substance by 3 degree celcius
[tex]\boxed{\sf Q=mc\Delta T}[/tex]
[tex]\\ \sf\longmapsto Q=1000(5000)(3)[/tex]
[tex]\\ \sf\longmapsto Q=15000000J[/tex]
[tex]\\ \sf\longmapsto Q=1.5\times 10^7J[/tex]
Proper physical exercise makes bones _[blank 1]_.
People with stronger muscles and bones have better _[blank 2]_.
Which option shows the words that correctly fill in blank 1 and blank 2, in that order?
longer, flexibilitylonger, flexibility , ,
stronger, posturestronger, posture , ,
longer, posturelonger, posture , ,
stronger, flexibility
stronger, posturestronger, posture
hope that helped
Use the values from PRACTICE IT to help you work this exercise. If the current in each wire is doubled, how far apart should the wires be placed if the magnitudes of the gravitational and magnetic forces on the upper wire are to be equal
A body is supported by a helical spring and causes an extension of 1.5 cm in the spring. If the mass is set into vertical oscillation, calculate the period of the oscillation.
Answer:
please follow Me
Explanation:
if the answer is right then like me otherwise you can share the right answer
What is the magnitude of the force between a 25μC charge exerts on a -10μC charge 8.5cm away?
Answer:
Force,
[tex]F = \frac{kQ_{1} Q_{2} }{ {r}^{2} } \\ F = \frac{(9 \times {10}^{9}) \times (25 \times {10}^{ - 6}) \times (10 \times {10}^{ - 6} ) }{ {(0.85)}^{2} } \\ \\ F = 3.114 \: newtons[/tex]
The magnitude of the force between a 25μC charge exerts on a -10μC charge 8.5cm away would be 311.4 N.
What is Coulomb's Law?Coulomb's law can be stated as the product of the charges and the square of the distance between them determine the force of attraction or repulsion acting in a straight line between two electric charges.
The math mathematical expression for the coulomb's law given as
F= k Q₁Q₂/r²
where F is the force between two charges
k is the electrostatic constant which is also known as the coulomb constant,it has a value of 9×10⁹
Q₁ and Q₂ are the electric charges
r is the distance between the charges
As given in the problem two charges a 25μC charge exerts on a -10μC charge 8.5cm away
By substituting the respective values in the above formula of Coulomb law
F =9×10⁹×(25×10⁻⁶)×(-10×10⁻⁶)/(8.5×10⁻²)²
F= -311.4 N
A negative sign represents that the force is attractive in nature
Thus, the magnitude of the force is 311.4 N.
Learn more about Coulomb's law from here
https://brainly.com/question/506926
#SPJ2
Snell's Law: Light goes from material having a refractive index of n 1 into a material with refractive index n 2. If the refracted light is bent away from the normal, what can you conclude about the indices of refraction
Answer:
a) the light is close to normal therefore the reference incidence of medium 1 is less than medium n2 where the ray is transmitted.
b) The ray is far from normal in this case the refractive index of medium 1 is greater than index of medium 2
Explanation:
The expression for the angle of refraction is
n₁ sin θ₁ = n₂ sin θ₂
refractive index n₁ is for incident light and n₂ is for transmitted light.
We have two cases
a) the light is close to normal therefore the reference incidence of medium 1 is less than medium n2 where the ray is transmitted.
b) The ray is far from normal in this case the refractive index of medium 1 is greater than index of medium 2
Parallel Wires: Two long, parallel wires carry currents of different magnitudes. If the current in one of the wires is doubled and the current in the other wire is halved, what happens to the magnitude of the magnetic force that each wire exerts on the other?
Answer:
Explanation:
Given force between 2 currents carrying
wires = F₀
Magnetic force between the2 wires =F₀= (μ₀/4π) x ( 2 (μ₀/4π) x ( 2I₁I₂ / μ) x L
where I₁=Current in wire 1
I₂= Current in wire 2
L= Length of the wire
when one current is doubled and the other is halved
I₁= 2 I₁
I₂= I₂/2
F₀ = (μ₀/4π) x ( 2× (2I₁) (I₂/2) / μ) x L
Q)what are convex mirrors?
Answer:
A curved mirror is a mirror with a curved reflecting surface. The surface may be either convex or concave. Most curved mirrors have surfaces that are shaped like part of a sphere, but other shapes are sometimes used in optical devices.
A convex mirror (or lens) is one constructed so that it is thicker in the middle than it is at the edge.
