Answer:
Displacement current flows in the dielectric material(insulated region)
Explanation:
Firstly a capacitor stores charge when a capacitor is charging (or discharging), current flows in the circuit. Also, there is no charge transfer in the dielectric material in the capacitor which is contradictory to the flow of current. Hence, displacement current is the current in the insulated region due to the changing electric flux.
(a) Calculate the force needed to bring a 800 kg car to rest from a speed of 85.0 km/h in a distance of 115 m (a fairly typical distance for a nonpanic stop).
N
(b) Suppose instead the car hits a concrete abutment at full speed and is brought to a stop in 2.00 m. Calculate the force exerted on the car and compare it with the force found in part (a), i.e. find the ratio of the force in part(b) to the force in part(a).
(force in part (b) / force in part (a))
Answer:
2Al + 2H2O + 2NaOH ⟶ 3H2 + 2NaAlO2
Chất rắn màu xám bạc của nhôm (Al) tan dần trong dung dịch, sủi bọt khí là hidro (H2).
Explanation:
A ring with an 18mm diameter falls off a scientist's finger into the solenoid in the lab. The solenoid is 25 cm long, 5.0 cm in diameter and has 1500 turns. When turned on, the current in the solenoid is increases linearly to 20 A in 1 second. What is the induced emf in the ring?
a) 2.0 x 10-5 v
b) 3.8 x 10-5 v
c) 1.2 x 10-3 v
d) 1.9 x 10-4 v
Answer:
the answer should be b) 3.8 x 10-5 v
A 30-cm-diameter, 90-cm-high vertical cylindrical container is partially filled with 60-cm-high water. Now the cylinder is rotated at a constant angular speed of 180 rpm. Determine how much the liquid level at the center of the cylinder will drop as a result of this rotational motion.
Answer:
[tex]\triangle h_c =0.204m[/tex]
Explanation:
Diameter [tex]d=30cm[/tex]
Height [tex]h=90cm[/tex]
Fill height [tex]h_f=60cm[/tex]
Angular speed [tex]N=180rpm[/tex]
Generally the equation for Angular velocity is mathematically given by
[tex]\omega=\frac{2 \pi*N}{60}[/tex]
[tex]\omega=\frac{2 \pi*180}{60}[/tex]
[tex]\omega=18.85rads/s[/tex]
Generally the equation for Liquid surface is mathematically given by
[tex]\mu_s=h*\frac{\omega^2*0.15^2}{4*9.81}[/tex]
[tex]\mu_s=0.396m[/tex]
Therefore the liquid drop at center due to rotation is
[tex]\triangle h_c =h-\mu_s[/tex]
[tex]\triangle h_c =0.60-0.396[/tex]
[tex]\triangle h_c =0.204m[/tex]
Consider two points in an electric field. The potential at point 1, V1, is 33 V. The potential at point 2, V2, is 175 V. An electron at rest at point 1 is accelerated by the electric field to point 2.
Required:
Write an equation for the change of electric potential energy ΔU of the electron in terms of the symbols given.
Answer:
ΔU = e(V₂ - V₁) and its value ΔU = -2.275 × 10⁻²¹ J
Explanation:
Since the electric potential at point 1 is V₁ = 33 V and the electric potential at point 2 is V₂ = 175 V, when the electron is accelerated from point 1 to point 2, there is a change in electric potential ΔV which is given by ΔV = V₂ - V₁.
Substituting the values of the variables into the equation, we have
ΔV = V₂ - V₁.
ΔV = 175 V - 33 V.
ΔV = 142 V
The change in electric potential energy ΔU = eΔV = e(V₂ - V₁) where e = electron charge = -1.602 × 10⁻¹⁹ C and ΔV = electric potential change from point 1 to point 2 = 142 V.
So, substituting the values of the variables into the equation, we have
ΔU = eΔV
ΔU = eΔV
ΔU = -1.602 × 10⁻¹⁹ C × 142 V
ΔU = -227.484 × 10⁻¹⁹ J
ΔU = -2.27484 × 10⁻²¹ J
ΔU ≅ -2.275 × 10⁻²¹ J
So, the required equation for the electric potential energy change is
ΔU = e(V₂ - V₁) and its value ΔU = -2.275 × 10⁻²¹ J
A rectangular loop of wire with sides 0.129 and 0.402 m lies in a plane perpendicular to a constant magnetic field (see part a of the drawing). The magnetic field has a magnitude of 0.888 T and is directed parallel to the normal of the loop's surface. In a time of 0.172 s, one-half of the loop is then folded back onto the other half, as indicated in part b of the drawing. Determine the magnitude of the average emf induced in the loop.
Answer:
[tex]0.2677\ \text{V/m}[/tex]
Explanation:
A = Area of loop = [tex]0.129\times0.402[/tex]
B = Magnetic field = [tex]0.888\ \text{T}[/tex]
t = Time taken = [tex]0.172\ \text{s}[/tex]
Electric field is given by
[tex]E=B\dfrac{dA}{dt}\\\Rightarrow E=0.888\times\dfrac{0.129\times 0.402}{0.172}\\\Rightarrow E=0.2677\ \text{V/m}[/tex]
The emf induced is [tex]0.2677\ \text{V/m}[/tex].
I NEEED HELP IN PHYSICS PLEASE!
Answer:
in which topic you need help
An airplane which intends to fly due south at 250 km/hr experiences a wind blowing westward at 40 km/hr. What is the actual speed of the airplane relative to the ground?
Answer:
simple is rumple a daily ok I'll be
Physics question plz help ASAP
Answer:
Option D.
Explanation:
From the question given above, the following data were obtained:
Force applied (F) = 5 N
Extention (e) = 0.075 m
Spring constant (K) =?
The spring constant for the spring can be obtained as follow:
F = Ke
5 = K × 0.075
Divide both side by 0.075
K = 5 / 0.075
K = 67 N/m
Thus, the spring constant for the spring is 67 N/m
Hai quả cầu kim loại nhỏ giống nhau, mang điện tích q1 = 2.10-8 C; q2 = 6.10-8 C, đặt cách
nhau một đoạn r trong không khí thì chúng đẩy nhau bằng một lực là 18.10-5 N. Cho hai quả cầu
tiếp xúc nhau rồi đưa về khoảng cách cũ thì lực tương tác giữa hai quả cầu là:
Answer:
fgggggffgggcffghhhjjkuuu of to ok with queen size of your yyyygtyttttttyyyhgggghhhhfrghjjkkkExplanation:
jjjgggyuuuuiiii hhjiiihuyyuuugggyujjhhhhggghhhjjhhhhjhhui
A force of 200 N, acting at 60° to the horizontal, accelerates a block of mass 50 kg along a horizontal plane. Calculate the component of the 200N force that accelerates the block horizontally
Answer:
Explanation:
a) Fx = F cos (θ)
= (200) cos(60)
= 100 N
b) FR = ma
Fx + Ff = ma
100 + Ff = (50)(1,5)
Ff = 75 - 100
= -25 N
c) Fy = F sin θ
= (200) sin(60)
= 173,2 N
define nortons theorem
Answer:
In direct-current circuit theory, Norton's theorem is a simplification that can be applied to networks made of linear time-invariant resistances, voltage sources, and current sources. At a pair of terminals of the network, it can be replaced by a current source and a single resistor in parallel.
A rock is suspended by a light string. When the rock is in air, the tension in the string is 37.8 N. When the rock is totally immersed in water, the tension is 32.0 N. When the rock is totally immersed in an unknown liquid, the tension is 20.2 N. What is the Density of the unknown liquid?
When the rock is suspended in the air, the net force on it is
∑ F₁ = T₁ - m₁g = 0
where T₁ is the magnitude of tension in the string and m₁g is the rock's weight. So
T₁ = m₁g = 37.8 N
When immersed in water, the tension reduces to T₂ = 32.0 N. The net force on the rock is then
∑ F₂ = T₂ + B₂ - m₁g = 0
where B₂ is the magnitude of the buoyant force. Then
B₂ = m₁g - T₂ = 37.8 N - 32.0 N = 5.8 N
B₂ is also the weight of the water that was displaced by submerging the rock. Let m₂ be the mass of the displaced water; then
5.8 N = m₂g ==> m₂ ≈ 0.592 kg
If one takes the density of water to be 1.00 g/cm³ = 1.00 × 10³ kg/m³, then the volume of water V that was displaced was
1.00 × 10³ kg/m³ = m₂/V ==> V ≈ 0.000592 m³ = 592 cm³
and this is also the volume of the rock.
When immersed in the unknown liquid, the tension reduces further to T₃ = 20.2 N, and so the net force on the rock is
∑ F₃ = T₃ + B₃ - m₁g = 0
which means the buoyant force is
B₃ = m₁g - T₃ = 37.8 N - 20.2 N = 17.6 N
The mass m₃ of the liquid displaced is then
17.6 N = m₃g ==> m₃ ≈ 1.80 kg
Then the density ρ of the unknown liquid is
ρ = m₃/V ≈ (1.80 kg)/(0.000592 m³) ≈ 3040 kg/m³ = 3.04 g/cm³
What distance do I cover if I travel at 10 m/s E for 10s?
Answer:
100m
Explanation:
i think this is the answer because the formula for distance is
d=speed×time in this case the speed is 10m/s and the time is 10s therefore the distance will be
10m/s×10s
=100m
I hope this helps
Answer:
100 m
Explanation: this is when you need to find velocity and the formula for velocity is displacement by time taken.
An auto mechanic needs to determine the emf and internal resistance of an old battery. He performs two measurements: in the first, he applies a voltmeter to the battery's terminals and reads 11.9 V;11.9 V; in the second, he applies an ammeter to the terminals and reads 16.1 A.16.1 A.
What are the battery's emf E and internal resistance r?
Answer:
Hence the battery's emf E is ε = 11.9 V.
The internal resistance is r = 0.739 ohms.
Explanation:
Now we know that
Voltage V = 11.9 V.
Current I = 16.1 A.
Hence this is an ideal voltmeter there are no current flows when the Voltmeter is applied.
ε = V + I r
∵ I = 0
ε = V
ε = 11.9 V
Then the ammeter is applied.
Let's take ( r ) to be the total resistance which is equal to internal resistance.
V = I r
r = [tex]\frac{V}{I}[/tex]
[tex]= \frac{11.9}{16.1}[/tex]
r = 0.739 ohms
The battery's emf (E) and internal resistance (r) are 11.9 Volts and 0.739 Ampere respectively.
Given the following data:
Voltage = 11.9 Volts.Current = 16.1 Amperes.To determine the battery's emf (E) and internal resistance (r):
How to calculate emf (E).For an ideal voltmeter, there isn't a flow of current and as such the current is equal to 0.
Mathematically, emf (E) is given by this formula:
[tex]E = V + IR[/tex]
Substituting the given parameters into the formula, we have;
[tex]E = 11.9 + 0R\\\\E = 11.9 + 0[/tex]
E = 11.9 Volts.
For the internal resistance (r):
Note: The total resistance is equal to internal resistance.
Applying Ohm's law, we have:
[tex]R = \frac{V}{I} \\\\R = \frac{11.9}{16.1}[/tex]
R = r = 0.739 Ampere.
Read more current here: https://brainly.com/question/25813707
Simple Pendulum: A 34-kg child on an 18-kg swing set swings back and forth through small angles. If the length of the very light supporting cables for the swing is 4.9 m, how long does it take for each complete back-and-forth swing
Answer:
The correct answer is "4.443 sec".
Explanation:
Given:
Mass of child,
= 34 kg
Mass of swing,
= 18 kg
Length,
= 4.9 m
The time period of pendulum will be:
T = [tex]2 \pi \sqrt{4g}[/tex]
= [tex]2 \pi \sqrt{\frac{4.9}{9.8} }[/tex]
= [tex]4.443 \ sec[/tex]
Answer:
The time taken to back and forth is 4.4 s .
Explanation:
Length, L = 4.9 m
let the time period is T.
Acceleration due to gravity, g = 9.8 m/s^2
Use the formula of time period
[tex]T = 2 \pi\sqrt{L}{g}\\\\T = 2 \times 3.14\sqrt{4.9}{9.8}\\\\T = 4.4 s[/tex]
Explain why the motor turns. Consider the Lorentz (magnetic) force we have discussed in class, and how this would apply here. Why did you have to remove only half the insulation on the ends of the wire
Solution :
Owing to the continuous attraction and repulsion force caused by the magnet or the electromagnet around the core of the motor produces a unidirectional torque whose direction is given by the Lorentz force, [tex]$F=q(\vec v \times \vec B)$[/tex], and thus the torque causes the rotation of the electric motor.
Removing half the insulation from the coil makes it to rotate just half a turn. When the half insulation is removed, the coil turns half and the rest of the time the connection terminates. The rest half turn will be provided by the angular momentum. Now after this half turn by the angular momentum, the connections will again be connected and again the torque will work on it to rotate the half turn. This continues and the motor rotates.
What are the examples of pulley? Plz tell the answer as fast as possible plz.
Answer:
elevators
Theatre system
construction pulley
lifts
Answer:
elevator,cargo lift system
What is the largest known star?
Answer:
UY Scuti is slightly larger than VY Canis Majoris
Explanation:
These stars are millions of miles away and cannot be seen by the naked eye.
Beetlejuice is another large star that can be seen by the eye.
Air enters a nozzle steadily at 2.21 kg/m3 and 20 m/s and leaves at 0.762 kg/m3 and 150 m/s. If the inlet area of the nozzle is 60 cm2, determine (a) the mass flow rate through the nozzle, and (b) the exit area of the nozzle
a) The mass flow rate through the nozzle is 0.27 kg/s.
b) The exit area of the nozzle is 23.6 cm².
a) The mass flow rate through the nozzle can be calculated with the following equation:
[tex] \dot{m_{i}} = \rho_{i} v_{i}A_{i} [/tex]
Where:
[tex]v_{i}[/tex]: is the initial velocity = 20 m/s
[tex]A_{i}[/tex]: is the inlet area of the nozzle = 60 cm²
[tex]\rho_{i}[/tex]: is the density of entrance = 2.21 kg/m³
[tex] \dot{m} = \rho_{i} v_{i}A_{i} = 2.21 \frac{kg}{m^{3}}*20 \frac{m}{s}*60 cm^{2}*\frac{1 m^{2}}{(100 cm)^{2}} = 0.27 kg/s [/tex]
Hence, the mass flow rate through the nozzle is 0.27 kg/s.
b) The exit area of the nozzle can be found with the Continuity equation:
[tex] \rho_{i} v_{i}A_{i} = \rho_{f} v_{f}A_{f} [/tex]
[tex] 0.27 kg/s = 0.762 kg/m^{3}*150 m/s*A_{f} [/tex]
[tex] A_{f} = \frac{0.27 kg/s}{0.762 kg/m^{3}*150 m/s} = 0.00236 m^{2}*\frac{(100 cm)^{2}}{1 m^{2}} = 23.6 cm^{2} [/tex]
Therefore, the exit area of the nozzle is 23.6 cm².
You can find another example of mass flow rate here: https://brainly.com/question/13346498?referrer=searchResults
I hope it helps you!
a) Mass flow rate through the nozzle: 0.265 kilograms per second, b) Exit area of the nozzle: 23.202 square centimeters.
We determine the Mass Flow Rate through the nozzle and the Exit Area of the nozzle by means of the Principle of Mass Conservation. A nozzle is a device that works at Steady State, so that Mass Balance can be reduced into this form:
[tex]\dot m_{in} = \dot m_{out}[/tex] (1)
Where:
[tex]\dot m_{in}[/tex] - Inlet mass flow, in kilograms per second.
[tex]\dot m_{out}[/tex] - Outlet mass flow, in kilograms per second.
Given that air flows at constant rate, we expand (1) by dimensional analysis:
[tex]\rho_{in} \cdot A_{in}\cdot v_{in} = \rho_{out}\cdot A_{out}\cdot v_{out}[/tex] (2)
Where:
[tex]\rho_{in}, \rho_{out}[/tex] - Air density at inlet and outlet, in kilograms per cubic meter.
[tex]A_{in}, A_{out}[/tex] - Inlet and outlet area, in square meters.
[tex]v_{in}, v_{out}[/tex] - Inlet and outlet velocity, in meters per second.
a) If we know that [tex]\rho_{in} = 2.21\,\frac{kg}{m^{3}}[/tex], [tex]A_{in} = 60\times 10^{-4}\,m^{2}[/tex] and [tex]v_{in} = 20\,\frac{m}{s}[/tex], then the mass flow rate through the nozzle is:
[tex]\dot m = \rho_{in}\cdot A_{in}\cdot v_{in}[/tex]
[tex]\dot m = \left(2.21\,\frac{kg}{m^{3}} \right)\cdot (60\times 10^{-4}\,m^{2})\cdot \left(20\,\frac{m}{s} \right)[/tex]
[tex]\dot m = 0.265\,\frac{kg}{s}[/tex]
The mass flow rate through the nozzle is 0.265 kilograms per second.
b) If we know that [tex]\rho_{in} = 2.21\,\frac{kg}{m^{3}}[/tex], [tex]A_{in} = 60\times 10^{-4}\,m^{2}[/tex], [tex]v_{in} = 20\,\frac{m}{s}[/tex], [tex]\rho_{out} = 0.762\,\frac{kg}{m^{3}}[/tex] and [tex]v_{out} = 150\,\frac{m}{s}[/tex], then the exit area of the nozzle is:
[tex]\rho_{in} \cdot A_{in}\cdot v_{in} = \rho_{out}\cdot A_{out}\cdot v_{out}[/tex]
[tex]A_{out} = \frac{\rho_{in}\cdot A_{in}\cdot v_{in}}{\rho_{out}\cdot v_{out}}[/tex]
[tex]A_{out} = \frac{\left(2.21\,\frac{kg}{m^{3}} \right)\cdot (60\times 10^{-4}\,m^{2})\cdot \left(20\,\frac{m}{s} \right)}{\left(0.762\,\frac{kg}{m^{3}} \right)\cdot \left(150\,\frac{m}{s} \right)}[/tex]
[tex]A_{out} = 2.320\times 10^{-3}\,m^{2}[/tex]
[tex]A_{out} = 23.202\,cm^{2}[/tex]
The exit area of the nozzle is 23.202 square centimeters.
What is the maximum speed at which a car can round a curve of 25-m radius on a level road if the coefficient of static friction between the tires and road is 0.80?
I assume the curve is flat and not banked. A car making a turn on the curve has 3 forces acting on it:
• its weight, mg, pulling it downward
• the normal force from contact with the road, n, pushing upward
• static friction, f = µn, directed toward the center of the curve (where µ is the coefficient of static friction)
By Newton's second law, the net forces on the car in either the vertical or horizontal directions are
∑ F (vertical) = n - mg = 0
∑ F (horizontal) = f = ma
where a is the car's centripetal acceleration, given by
a = v ²/r
and where v is the maximum speed you want to find and r = 25 m.
From the first equation, we have n = mg, and so f = µmg. Then in the second equation, we have
µmg = mv ²/r ==> v ² = µgr ==> v = √(µgr )
So the maximum speed at which the car can make the turn without sliding off the road is
v = √(0.80 (9.80 m/s²) (25 m)) = 14 m/s
The voltage in an EBW operation is 45 kV. The beam current is 50 milliamp. The electron beam is focused on a circular area that is 0.50 mm in diameter. The heat transfer factor is 0.87. Calculate the average power density in the area in watt/mm2.
Answer:
[tex]P_d=6203.223062W/mm^2[/tex]
Explanation:
From the question we are told that:
Voltage [tex]V=45kV[/tex]
Current [tex]I=50mAmp[/tex]
Diameter [tex]d=0.50mm[/tex]
Heat transfer factor [tex]\mu= 0.87.[/tex]
Generally the equation for Power developed is mathematically given by
[tex]P=VI\\\\P=45*10^3*50*10^{-3}[/tex]
[tex]P=2.250[/tex]
Therefore
Power in area
[tex]P_a=1400*0.87[/tex]
[tex]P_a=1218watt[/tex]
Power Density
[tex]P_d=\frac{P_a}{Area}[/tex]
[tex]P_d=\frac{1218}{\pi(0.5^2/4)}[/tex]
[tex]P_d=6203.223062W/mm^2[/tex]
A gymnast weighs 450 N. She stands on a balance beam of uniform construction which weighs 250 N. The balance beam is 3.0 m long and is supported at each end. If the support force at the right end is four times the force at the left end, how far from the right end is the gymnast
Answer:
x = 9.32 cm
Explanation:
For this exercise we have an applied torque and the bar is in equilibrium, which is why we use the endowment equilibrium equation
Suppose the counterclockwise turn is positive, let's set our reference frame at the left end of the bar
- W l / 2 - W_{child} x + N₂ l = 0
x = [tex]\frac{-W l/2 + n_2 l}{W_{child}}[/tex] 1)
now let's use the expression for translational equilibrium
N₁ - W - W_(child) + N₂ = 0
indicate that N₂ = 4 N₁
we substitute
N₁ - W - W_child + 4 N₁ = 0
5 N₁ -W - W_{child} = 0
N₁ = ( W + W_{child}) / 5
we calculate
N₁ = (450 + 250) / 5
N₁ = 140 N
we calculate with equation 1
x = -250 1.50 + 4 140 3) / 140
x = 9.32 cm
A refrigerator has a coefficient of performance equal to 4.00. The refrigerator takes in 110 J of energy from a cold reservoir in each cycle. (a) Find the work required in each cycle. J (b) Find the energy expelled to the hot reservoir. J
Answer:
The correct answer is:
(a) 27.5 Joules
(b) 141.5 Joules
Explanation:
Given:
Energy,
[tex]Q_c = 110 \ J[/tex]
Coefficient of performance refrigerator,
[tex]Cop(refrig)=4[/tex]
(a)
As we know,
⇒ [tex]Cop(refrig) = \frac{Q_c}{Work}[/tex]
or,
⇒ [tex]Work=\frac{Q_c}{Cop(refrig)}[/tex]
[tex]=\frac{110}{4}[/tex]
[tex]=27.5 \ Joules[/tex]
(b)
⇒ [tex]Heat \ expelled = Heat \ removed +Work \ done[/tex]
or,
⇒ [tex]Q_h = Q_c+Work[/tex]
[tex]=114+27.5[/tex]
[tex]=141.5 \ Joules[/tex]
In a photoelectric effect experiment, it is observed that violet light does not eject electrons from a particular metal. Next, red light with the same intensity is incident on the same metal. Which result is possible
Answer:
No ejection of photo electron takes place.
Explanation:
When a photon of suitable energy falls on cathode, then the photoelectrons is emitted from the cathode. This phenomenon is called photo electric effect.
The minimum energy required to just eject an electron is called work function.
The photo electric equation is
E = W + KE
where, E is the incident energy, W is the work function and KE is the kinetic energy.
W = h f
where. h is the Plank's constant and f is the threshold frequency.
Now, when the violet light is falling, no electrons is ejected. When the red light is falling, whose frequency is less than the violet light, then again no photo electron is ejected from the metal surface.
A scientist who studies the tiny microorganisms of the environment .
geologist
meteorologist
microbiologist
entomologist
Question:- A scientist who studies the tiny microorganisms of the environment
Answer:- MicrobiologistExplanation:-
Microbiologist means a person who studies micro sized living organisms
Microbiologist word is combination of two words Micro and biologist
Micro stands for objects which cannot be seen with the naked eyes and are very small in sizeBiologist a person who studies living forms.Answer:
microbiologist i think
hope it helps
please mark Brainliest if you think the answer is correct
What is the incorrect statement regarding the isotopes of the same element?
1) Electronic configuration is equal
2) Mass number is equal
3) Number of protons are equal
4) Number of electrons are equal
Answer:
1231
Explanation:
A silicon solar cell behaves like a battery with a 0.46 V terminal voltage. Suppose that 1.0 W of light of wavelength 620 nm falls on a solar cell and that 50%% of the photons give their energy to charge carriers, creating a current. What is the solar cell's efficiency that is, what percentage of the energy incident on the cell is converted to electric energy?
We have that the percentage of the energy incident on the cell that is converted to electric energy is
[tex]n=11\%[/tex]
From the question we are told that:
Voltage [tex]V=0.46V[/tex]
Power of light [tex]P=1.0W[/tex]
Wavelength [tex]w=620nm[/tex]
50 \% of the photons give their energy to charge carriers,
Generally, the equation for number of Protons is mathematically given by
[tex]N_p=\frac{P}{E}[/tex]
[tex]N_p=\frac{P \lambda}{hc}[/tex]
[tex]N_p=\frac{1}{(6.62*10^(-34)}*\frac{3*10^8}{(570*10^{-9}))}[/tex]
[tex]N_p=2.87*10^{18}[/tex]
Generally, the equation for Number of electron is mathematically given by
[tex]N_e=50 \% *n_3[/tex]
[tex]N_e=0.5*2.87*10^{18}[/tex]
[tex]N_e=1.43*10^{18}[/tex]
Therefore
Total current
[tex]I= e*N_e[/tex]
Where
e=electron Charge
Therefore
[tex]I=1.43*10^{18}*1.6*10^-{19}[/tex]
[tex]I=0.230A[/tex]
Generally, the equation for Power is mathematically given by
[tex]P=VI[/tex]
[tex]P=0.46*0.230[/tex]
[tex]P=0.1058W[/tex]
Therefore
Efficiency
[tex]n=\frac{0.1058}{1}[/tex]
[tex]n=0.1058[/tex]
[tex]n=11\%[/tex]
In conclusion
The percentage of the energy incident on the cell that is converted to electric energy is
[tex]n=11\%[/tex]
For more information on this visit
https://brainly.com/question/1252435
a. Do the waves made by the two faucets travel faster than the waves made by just one faucet?
b. How do you know this? Describe how the two-faucet wave pattern compares with the one-faucet pattern.
c. Describe what happens to the two-faucet wave pattern as the separation of the faucets is increased.
Answer:
asdasd dsa dasdasd sadas dasd asdasd asd asd dsa asdd 223 aasd ada dasd sa dasd dsaa sd adsd asasd
Explanation:
if 6000j of energy is supplid to a machine to lift a load of 300N through a vvertical height of 1M calculatework out put
Answer:
300J
Explanation:
Work done = Force x the distance travelled in the direction of the force
=300 x 1
=300J
A T-shirt is launched at an angle of 30° with an initial velocity of 25 m/s how long does it take to reach the peak? How long is it in the air for totally?
Answer:
The launched angle θ = 30 degrees, the initial velocity Vo = 20 m/s, the initial horizontal velocity Vox= ?, the initial vertical velocity Voy = ?, the time of flight t = ? the maximum height h = ?
Vox = Vo * (cos of 30 degrees)
Voy = Vo * (sin of 30 degrees)
t = 2 * (Voy / g)
h = Voy * 0.5 t - 1/2 g * (0.5t)^2
I have given the equations for you to use, just plug – in the values and then solve in a step by step manner.
Answer:
approximately 15.68 meters.
Explanation:
Here is how;
First, let's calculate the time of flight for the t-shirt. We can use the vertical motion equation:
y = y0 + v0y * t - 0.5 * g * t^2
where:
y is the vertical displacement (27.7 m)
y0 is the initial vertical position (0 m)
v0y is the vertical component of the initial velocity (v0 * sin(theta))
g is the acceleration due to gravity (9.8 m/s^2)
t is the time of flight
Plugging in the values:
27.7 = 0 + (25.8 * sin(63.6°)) * t - 0.5 * 9.8 * t^2
Simplifying the equation, we get a quadratic equation:
4.9t^2 - (25.8 * sin(63.6°))t + 27.7 = 0
Solving this quadratic equation will give us the time of flight, t. Using the quadratic formula, we find that:
t ≈ 1.23 s
Now, let's find the horizontal displacement of the t-shirt using the horizontal motion equation:
x = x0 + v0x * t
where:
x is the horizontal displacement
x0 is the initial horizontal position (0 m)
v0x is the horizontal component of the initial velocity (v0 * cos(theta))
t is the time of flight
Plugging in the values:
x = 0 + (25.8 * cos(63.6°)) * 1.23
Calculating this:
x ≈ 14.92 m
The t-shirt falls short of reaching the person by the horizontal distance of:
Shortfall = 30.6 m - 14.92 m
Calculating this:
Shortfall ≈ 15.68 m
Therefore, the t-shirt will be approximately 15.68 meters short of reaching the person.
